Pass Laboratories X250.5 Bedienungsanleitung

X250.5 Owners Manual

passTM

X250.5 Owner’s Manual

May 17, 2006

X250.5 Owners Manual

The Pass Laboratories ™ X250.5 stereo amplifier embodies the de-

sign technolog y and refinements of the “X” series amplifiers includ-

ing extensions of the patented Supersymmetry™ circuit. Additionally

selected refinements of the XA series amplifiers have been incorpo-

rated into the X250.5 to significantly improve this products sonic

perfor mance in comparison to it’s immediate predecessor, the Pass

Laboratories™ X250.

The Supersymmetr y™ circuit topolog y was g ranted a U.S. patent in

1994, and was the result of 19 years of effor t by legendar y analog

designer and company founder Nelson Pass. T he amplifier uses

highly matched components in a classically simple single ended Class

A circuit. T he amplifier contains only two simple stages: the first is a

balanced Class A g ain stag e. Its output drives a bank of high power

devices operated as followers.

These are inherently low distor tion types of circuits, but their perfor-

mance is significantly improved when operated as balanced devices.

Distortion and noise identical to both halves of a balanced circuit can

be made to disappear at the output, and in a well-matched symmetric

circuit, most of the distortion and noise is identical.

Pass Laboratories Supersymmetr y™ enhances this effect by provid-

ing a connection between the two halves of the balanced circuit that

further perfects the match of common mode artifacts. Any distor-

tion and noise not already identical to the two halves is made more

identical by a factor of about 10. T he result of this perfected match

is improved noise cancellation at the output of the amplifier. From a

listeners standpoint this results in a more accurate presentation of the

soundstage and better resolution of low level detail.

Unlike feedback techniques where the g oal is to cor rect for the distor-

tion by feeding a gain stage an inversely distorted signal, Supersymme-

tr y™ seeks merely to create perfect matching between the two halves

of an otherwise well matched circuit.

Matched balanced power circuitr y typically sees a distortion and noise

reduction of about 90% (20 dB) through a balanced connection

without any additional effort. T he Supersymmetr y™ circuit delivers

another 90% reduction, so that the X series has about 1/100 of the

distortion of a conventionally simple and otherwise identical ampli-

fier. Distortion and noise can still be seen at the output of one half of

the circuit, but since it is virtually identical on the other half, these un-

desirable ar tifacts larg ely g o away at the speaker ter minals. T his gives

g ood measured perfor mance, and because a simple circuit produces it,

also sounds quiet excellent.

Introduction

X250.5 Owners Manual

Previously these kinds of simple Class A circuits have been popular

for their sound quality in low power amplifiers, but have not found

application at high power levels due to excessive distortion and low

efficiency. Supersymmetr y™ overcomes this bar rier, delivering the

sweetness, staging, and detail of very simple circuitr y up to kilowatt

power levels and beyond.

The X.5 Series amplifiers have the tremendous dynamic rang e (>140

dB) to do justice to the high-resolution digital recordings of the 21st

Centur y and the eleg ance to retrieve the micro dynamics offered by

the most sensitive loudspeakers. The simple but powerful circuitr y

moves easily from total silence to explosive transient and back to

silence without a trace and without infor mation loss. Ver y unlike

conventional high power amplifiers, they provide this level of power

with a subtlety befitting some of the better tube amplifiers. This per-

for mance is consistence across the audio spectr um and the amplifiers

are unconditionally stable into all speaker loads.

So relax and enjoy your amplifier. Call us if you ever have a problem

or question. You are welcome to ask questions or offer comments.

Thank you for buying our product.

X250.5 Owners Manual

You can position this amplifier most anywhere you wish, but it re-

quires adequate ventilation. We do not recommend placing it in

enclosed cabinets or small closets without means for air to circulate

freely. Stacking these power amplifiers directly upon each other is not

recommended for the same reason. T his amplifier typically idles at

slightly less than 350 watts, most of which dissipates as heat across

the heatsinks. As a point of reference, these heatsinks should never

become too hot to touch for several seconds.

Let’s talk about AC power requirements. This amplifier draws about

3 amps (continuous r ms) at 120 volts out of the wall during nor mal

operation, and this power draw ref lects mostly the idle cur rent that

we r un through the output stag e. If you are driving a low impedance

load, you will draw more power than this, but this will not be typical.

The amplifier’s voltage and cur rent rating are indicated on the rear

panel. It will be 240 volts, 220 volts, 120 volts or 100 volts, all with

an appropriate rear mounted resetable circuit breaker. T he frequency

rating of the AC line source in all instances will be 50 to 60 Hz. Please

verify that the amplifiers indicated voltage requirements are consistent

with the line voltag e supplied at your location.

The Pass Laboratories™ X250.5 is provided with a conventional IEC

detachable AC line cord, which is rated at 15 amps. The safety ground

is attached to the chassis in the conventional approved manner. T he

AC power input to the amplifier r uns through a RF filter, which re-

moves high frequency noise coming into and g oing out of the ampli-

fier power supply.

Under no circumstances should you defeat the g round connection of

the power cord. For your safety, the chassis of the amplifier should be

earth g rounded. Signal g round is isolated from chassis, safety ground,

to reduce the incidence of g round loop noise. T he presence of a

safety g round will not deg rade the audio signal chain.

You may substitute an after market detachable IEC 320 style power cord

of your choosing; provided it is rated for at least 15 amps and it meets all

leg al requirements and has been approved by the local testing authority

for such things.

Looking at the rear panel you will see the IEC 320 AC power cord

receptacle, a ther mal magnetic breaker switch, two pairs of output con-

nectors, a pair of binding post connectors for remote turn-on, one RCA

input connector and one XLR balanced input connector.

Make sure that the breaker switch is off (down). Plug the AC cord into

Setup

X250.5 Owners Manual

the back of the amplifier, and then into the wall. Then turn the breaker

switch on (up). The lights in your house will blink when the power sup-

ply charges the capacitors; this is nor mal. This magnetic breaker switch

is not to be used as a safety disconnect during ser vicing and is not a

substitute for unplugging the power cord.

On the front panel, the “Standby” LED indicator should be glowing

blue, indicating that the power is on. The “Power” LED should not be

on. If the “Power” LED is on, don’t g et excited, just use the front panel

stand-by button to go into stand-by mode, with the “Standby” LED on

and the “Power “ LED off.

OK, so the amplifier is sitting there in stand-by mode with just the single

blue LED lit. No speaker connected, as yet. You can go ahead and con-

nect the source and speakers. Some speaker cables are ver y difficult to

work with due to physical size and construction, make sure the speaker

connections do not short together. It is recommended that you connect

the speaker ends of these cables first.

Some powered subwoofers require an audio signal ground reference and

their makers may sug gest that a black speaker ter minal is where this volt-

age reference might be found. On complementar y designs, which would

be typical of all power amps produced by Pass Laboratories™, this is

an incorrect and unsafe assumption. On all Pass Laboratories™ power

amplifiers a reference of 0 volts will be found only at pin 1 of the XLR

input or at the shell of the RCA input.

Reference connections for these devices require special consideration

when used with our product. If you have such a device, and wish to

use it with our product, please contact our Foresthill, California fac-

tor y for specific instr uctions.... you have been warned.

The amplifier can be driven single-end or balanced, if driving the am-

plifier single-ended, leave the supplied jumper in place (between pins

1 & 3 on the XLR). Your amplifier will operate without the jumper

in place, but perfor mance will be significantly diminished. You must

choose either XLR or RCA inputs it is not advised to try and r un both

concur rently.

Now that the source component is connected, make sure there is no

signal coming from it, probably by turning the volume all the way

down.

With the speakers connected, push the front panel button to activate

the amplifier. The “Power” LED will come on.

X250.5 Owners Manual

Do ever ybody a favor and try not to have shorted output cables. It

happens accidentally all the time, and the amplifier is designed to sur-

vive, mostly.

Of course it’s always possible that something could g o wrong. If so,

don’t g et excited, just relax. It’s really ag g ravating when something like

this doesn’t work, we understand, but it will g et fixed. We g o to a lot

of trouble to make products reliable, and the failure rate of our ampli-

fiers is very low. This is small comfor t to the few, but take it easy and

give us a call if you have problems.

People are often interested in how long it takes for these amplifiers

to break in. Perhaps a more salient question is how long does it take

them to reach their sonic best after tur n on. It takes about an hour for

them to fully war m up, and this is where we adjust them first. T hen

we adjust them ag ain and again over a couple of days, keeping the bias

and offset in the sweet spot. Our environment is about 23 degrees

Centig rade and the heat sinks will rise approximately 25 deg rees C.

above that, for an average on heat sink temperature of 48 deg rees C.

Sonically they are at their best when the heatsinks are approximately

50 deg rees C.

In your setup the temperature may var y a bit due to line voltage varia-

tions and ventilation, but this is not a big deal. You should be able to

put your hands on the heat sinks without discomfor t for 10 seconds

or so. It is nor mal for the heasink temperature to var y side-to-side and

front to back.

The amplifier has a ther mal cutout that will disconnect AC power if

the temperature exceeds 75 deg rees Centig rade. This should never

occur in real life.

More things to know

You can remotely operate the stand-by mode by applying 12 volts DC

to the single pair of binding post connectors on the rear of the ampli-

fier. The positive of the 12 volts DC goes to the red connector. This

connection has an actual operating range of about 9 volts to 15 volts

at a cur rent draw of approximately 5.0mA. T his switching will over-

ride the front panel button, so if you want the front panel button to

operate, leave the rear connection open.

So much for the most essential information.

You are ready to play music

X250.5 Owners Manual

The Pass Laboratories™ X250.5 is optimized for loads nominally rated

at 4 ohms and above. You can r un the amplifiers into a lower nominal

impedance without difficulty, and we are not aware of a speaker on the

market that presents unusual difficulty with these amplifiers.

The X.5 series amplifiers do not care par ticularly about the reactivity

of the load. Reactive loads typically will have slightly less distor tion

at a given voltage/cur rent level than resistive loads, but will make the

amplifier r un a little hotter. T he X.5 circuit was designed to be quite

happy driving electrostatic and other difficult speakers.

When driving transfor mer-coupled loads directly, as in some elec-

trostatic and ribbon designs, some attention must be paid to the DC

character of the situation. If the transfor mer primar y is being driven

raw with no protection from DC and your source has DC voltage, or

in cases where the small offset of the power amplifier is still too much,

you may create distor tion in the transfor mer and get less than optimal

perfor mance from it. Generally this is not the case with transfor mer-

coupled loudspeakers, but it does occasionally surface. In these cases,

take special care that the source does not contain a differential DC

component, and confir m the differential DC offset of the pre-ampli-

fier is sufficiently low. T his differential voltage is easily adjusted by a

qualified technician ar med with the appropriate ser vice documents.

We have a general recommendation about interconnects, which is that

they should cost less than the amplifier, and be f lexible enough to work

with. We have tried a lot of products and most of them work well, but

as a practical matter we cannot make blanket recommendations.

The amplifier is not sensitive to source interconnects or g round loops.

It is also not sensitive to radio frequency pickup, which allows some

flexibility in choosing source interconnects without shields, though

shields are always in g ood taste.

We prefer speaker cables that are thick and shor t. Silver and copper

are the prefer red metals. If you find any cable made of g old, please

gift us a couple hundred meters.

Fortunately the amplifier is not sensitive to the capacitive/inductive

character of some of the specialty speaker cables, so feel free to ex-

periment.

We have found that about 90 per cent of bad sounding cables are in

reality bad sounding connections, and we recommend that special at-

Speaker Interface

Interconnects and Speaker

Cables

X250.5 Owners Manual

tention be paid to cleanliness of contact surfaces and proper fit.

Speaker cables should be fir mly tightened down at the speaker output

ter minals, but do not use a wrench. T hese connectors will not with-

stand unrealistic foot-lbs of torque. Hand tightening without exces-

sive force is plenty.

Hardware Facts

So how long will this hardware last? It is our experience that, bar ring

abuse or the odd failure of a component, the first things to go will be

the power supply capacitors, and from experience, they will last 15 to

20 years before needing replacement. For tunately these components

die g racefully; typically with years of warning and are easily re placed.

After that, the long evity will de pend on the number of operating ther-

mal cycles, but we can attest to having had amplifiers operating in the

field in excess of 20 years with no par ticular mor tality except capaci-

tors. We don’t have g ood infor mation beyond that. More to the point,

we would sug gest that you not worr y about it. T his is a conser vatively

built industrial design, not a tweaky tube circuit r un on the brink of

failure. If it breaks, we will simply get it fixed, so sleep well.

X250.5 Owners Manual

All figures obtained after a 1 hour war mup, with regulated 120 VAC

power line. See manual notes about AC power line regulation.

Gain 30 dB

Freq. Response -3 dB at 1Hz, -3 dB at 100 kHz

Power Output 250 watts @ 1% THD, 1 kHz, 8 ohms

Maximum Output Voltag e plus, minus 60 volts

Maximum Output Current plus, minus 20 amps

Input Impedance 22 kohm balanced,

12 kohm single-ended

Damping factor 250 ref 8 ohms nominal

Slew rate plus, minus 50 V/uS

Output Noise 400 uV unweighted 20-20 kHz

Balanced CMRR -60 dB @ 1 kHz (input common

mode rejection ratio)

DC offset < 100 mV differential

Power Consumption 350 watts idle, 1000 watts max.

Temperature 25 degrees C. above ambient at idle.

Dimensions 19”W x 22”D x 9.5”H

Weight 110 Lbs.

For more infor mation please contact:

Pass Laboratories Inc.

P.O. Box 219,

24449 Foresthill Rd.,

Foresthill, CA 95631

Tel: 530.367.3690

Fax: 530.369.2193

www.passlabs.com

X250.5 Specifications

“Pass”, “pass”, “Pass Labs”, “Pass Laboratories”, Supersymmeter y”,

“Ale ph”, and “Zen” and are all registered trademarks of Pass

Laboratories, Inc., and all rights thereto are protected by law.

X250.5 Owners Manual

Please check with the factory-authorized distributor in the country you are

purchasing this product for specific war ranty infor mation.

All Pass Laboratories products purchased from an authorized Pass Labora-

tories dealer in Nor th America are covered by a transferable, limited 3-year

warranty. This war rantee includes all parts and labor charges incur red at the

repair facility in addition to return shipping to the domestic customer, exclu-

sive of subsequent damag es. Damage due to physical abuse is specifically

not covered under this warranty.

For this war ranty to apply the customer is responsible for retur ning the

product unmodified to the factor y within the warranty period. T he customer

assumes all responsibility for shipping and insurance to the factor y or a fac-

tor y specified repair facility. T he conditions and stipulations of this Pass

Laboratories warranty only applies to units sold new in Nor th America.

Non-North America customers should consult with their original Pass Labs

dealer or distributor for war rantee repair instr uction prior to contacting the

factor y or shipping product for repair.

Non-North American product must be returned to the country of origin for

warrantee service. Foreign distributors are only required to offer war ranty

ser vice on Pass Laboratories product that they have imported.

Please note: Conditions of war ranty ser vice and customer rights for product

purchased outside the United States may var y depending upon the distribu-

tor and local laws. Please check with your local distributor for specific rights

and details.

Any modifications to Pass Laboratories products that have not received

written factor y approval nullify all claims and void the warrantee. Should a

modified product be retur ned to the factor y for repair the owner will be re-

quired to pay all necessary charges for the re pair in addition to those charg es

required to return the product to it’s original configuration.

In the case of safety issues, no product shall be retur ned to the customer

without those safety issues being cor rected to the most recent accepted

standards.

Removal or alteration of original Pass Labs serial numbers voids the factory

warranty. Product with altered or missing serial numbers will be suspected

as counterfeit product.

Pass Laboratories will not repair or in any way indemnify any counterfeit or

cloned product.

Pass Laboratories does not offer products in voltages intended for inter-

national markets either to authorized Pass Labs dealers or to third par ties

located in the United States or Canada.

Warranty Information

Inhaltsverzeichnis

Andere Pass Laboratories Verstärker Handbücher

Pass Laboratories

Pass Laboratories XA60 Bedienungsanleitung

Pass Laboratories

Pass Laboratories X1000 Bedienungsanleitung

Pass Laboratories

Pass Laboratories XP-30 Bedienungsanleitung

Pass Laboratories

Pass Laboratories Aleph P Bedienungsanleitung

Pass Laboratories

Pass Laboratories Pass X5 Bedienungsanleitung

Pass Laboratories

Pass Laboratories XA200.5 Bedienungsanleitung

Pass Laboratories

Pass Laboratories XP-10 Bedienungsanleitung

Pass Laboratories

Pass Laboratories XP-25 Bedienungsanleitung

Pass Laboratories

Pass Laboratories INT-150 Bedienungsanleitung

Pass Laboratories

Pass Laboratories Aleph 1 Bedienungsanleitung

Pass Laboratories

Pass Laboratories pre-amplifier Bedienungsanleitung

Pass Laboratories

Pass Laboratories Volksamp Aleph 30 Bedienungsanleitung

Pass Laboratories

Pass Laboratories Aleph 1.2 Bedienungsanleitung

Pass Laboratories

Pass Laboratories XP-10 Bedienungsanleitung

Pass Laboratories

Pass Laboratories XP-12 Bedienungsanleitung

Pass Laboratories

Pass Laboratories Pass Aleph 60 Bedienungsanleitung

Pass Laboratories

Pass Laboratories X2.5 Bedienungsanleitung

Pass Laboratories

Pass Laboratories XP-10 Bedienungsanleitung

Pass Laboratories

Pass Laboratories Pass X250 Bedienungsanleitung

Pass Laboratories

Pass Laboratories INT-25 Bedienungsanleitung

Pass Laboratories

Pass Laboratories Aleph L Bedienungsanleitung

Pass Laboratories

Pass Laboratories XP-20 Bedienungsanleitung

Pass Laboratories

Pass Laboratories XA100.5 Bedienungsanleitung

Pass Laboratories

Pass Laboratories X2.2 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung