Passtech AP300 Bedienungsanleitung
Passtech Co., Ltd.
Copyright ⓒ2017 Passtech Inc. All rights reserved. You are strictly prohibited to copy, disclose, distribute,
or use this document in part or as a whole for any purposes other than those for which this document is
disclosed. This document is copyrighted and contains confidential information and other intellectual property
rights of Passtech Inc. Any unauthorized use, copy, disclosure or distribution constitutes infringement of
Passtech’s intellectual property rights.
USER GUIDE
ACCESS POINT
(AP300_Ethernet Setting)
AP300 (ACCESS POINT) User Manual
Version: 1.0 2 http://www.esmartlock.com
Passtech Inc. reserves the right to make changes to its applications or services or to discontinue any
application or service at any time without notice. Passtech provides customer assistance in various technical
areas, but does not have full access to data concerning the use and applications of customer's products.
Therefore, Passtech assumes no liability and is not responsible for customer applications or software design
or performance relating to systems or applications incorporating Passtech products. In addition, Passtech
assumes no liability and is not responsible for infringement of patents and/or any other intellectual or
industrial property rights of third parties, which may result from assistance provided by Passtech.
Composition of the information in this manual has been done to the best of our knowledge. Passtech does
not guarantee the correctness and completeness of the details given in this manual and may not be held
liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may
not be completely avoided, we are always grateful for your useful tips.
We have our development center in South Korea to provide technical support. For any technical assistance
can contact our technical support team as below;
E-mail: passtech@esmartlock.com
AP300 (ACCESS POINT) User Manual
Version: 1.0 3 http://www.esmartlock.com
Table of Contents
1. Components Preparation ..........................................................4
1.1 SETUP Components...................................................................... 4
1.2 Setting Diagram ............................................................................. 4
2. AP Setting .....................................................................................5
2.1 SERVER & AP300 Communication Diagram................................. 5
2.2 AP Setting...................................................................................... 5
3. Server Setting.............................................................................11
3.1 Server pre-setting (DB Connection)..............................................11
3.2 Server Connection ....................................................................... 13
3.3 Server Startup and Shutdown...................................................... 17
6. Specification ...........................................................................18
7 Regulatory Statement .............................................................19
AP300 (ACCESS POINT) User Manual
Version: 1.0 5 http://www.esmartlock.com
2. AP Setting
2.1 SERVER & AP300 Communication Diagram
2.2 AP Setting
Before creating AP account, please check PC IP and TCP/IP first by running ‘Command Prompt’ and
inputting ‘ipconfig’ command as below.
①Open ‘AP300(2Bytes Floor)’.
Internet
AP300 (ACCESS POINT) User Manual
Version: 1.0 7 http://www.esmartlock.com
③Select an AP which you want to configure from the AP list, and input values in ‘Ethernet Setting’
referring to the description below.
Item
Description
Local IP
AP IP
Make sure this IP is only assigned to this AP
Local Port
Assign the port number on your own (Default: 5000)
Subnet
Input the value (Subnet Mask) checked in Command Prompt
Gateway
Input the value (Default Gateway) checked in Command Prompt
Server IP
Input the value (IPv4 Address) checked in Command Prompt
Server Port
Input the port number as set in Server program (Default 2274)
④Click ‘Setting’button to save the information to the selected AP, and check the message
‘Setting OK’from the message box below.
AP300 (ACCESS POINT) User Manual
Version: 1.0 8 http://www.esmartlock.com
⑤Select RF Channel and then click ‘Conn’button and check the message ‘Connected OK’from
the message box.
If it is connected well, ‘WRITE’and ‘READ’buttons will be activated.
⑥Click ‘READ’button to check current saved information.
AP300 (ACCESS POINT) User Manual
Version: 1.0 9 http://www.esmartlock.com
⑦Input values in ‘AP Setting’referring to the description below.
Item
Description
AP Name
AP name that will be inputted into AP Account in Client program
Assign AP ID on your own, but do not duplicate
Only English alphabet and number are available
(Any space or special characters cannot be contained)
RF Channel
RF Channels you would like to connect (11~25)
BUILD
Building number (1~50)
FLOOR
Floor number (1~99)
ROOMS
Room numbers (1~999)
⑧Click ‘WRITE’button to save the information of the selected AP, and check the message
‘Configuration writing OK’from message box.
⑨Click ‘READ’button again to check if the setting values are properly saved.
⑩If you want to set another AP, follow the steps from ②.
⑪After setting is completed, click ‘EXIT’to close the window.
⑫Click ‘New’ button from AP account window to enter new information.
⑬Input the following items and click ‘Save’button to save the entered information.
AP300 (ACCESS POINT) User Manual
Version: 1.0 10 http://www.esmartlock.com
Item
Description
AP Name
Input AP Name which you set in AP Settings
Server IP Update Flag
Check to update the information into Server program automatically
AP IP
Input AP IP address which you set in AP Settings
Server IP
Input IP address of a PC which Server is installed in
Server Port
Input server port (Default: 2274)
Channel
Input RF Channel which you set in AP Settings
Building No.
Select Building number which you set in AP Settings
Group ID
Input Group number which you set in AP Settings
Lock Start
Input Starting Room number of the lock which you set in AP Settings
Lock End
Input Ending Room number of the lock which you set in AP Settings
AP Status
Waiting / Connect OK / Connect Error
AP Layout ID
Select AP Layout ID same as you set in Custom Layout
⑭If you want to update the information, select the AP account from the list and click ‘Update’
button to activate the input boxes. Input the updated information and click ‘Save’button to
update.
⑮If you want to delete the information, select the AP account from the list and click ‘Delete’
button to delete.
Inhaltsverzeichnis
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
EnGenius
EnGenius EnStationACv2 Bedienungsanleitung
D-Link
D-Link DAP-3662 Bedienungsanleitung
xG Technology
xG Technology xMax CN1300 Bedienungsanleitung
Widelink
Widelink ezWave WAP-1100 Series Bedienungsanleitung
Edimax
Edimax CAP1200 Bedienungsanleitung
