Patton electronics 1205P Bedienungsanleitung

MODEM ELIMINATOR, V.35

1205P

(CTS ME-V.35)

INSTALLATION AND OPERATIONS MANUAL

Doc #: 113001UA

Part #: 07M1205P-A

An ISO-9001

CertifiedCompany

113001UA

PATTONELECTRONICSCO. ME-V.35 INSTALLATION AND OPERATIONS MANUAL

COPYRIGHTNOTICE

PROPRIETARY NOTICE

TheinformationcontainedhereinisproprietaryandconfidentialtoPattonElectronicsCo. Any

reproductionorredistributionofthispublication,inwholeorinpart,isexpresslyprohibited

unlesswrittenauthorizationisgivenbyPattonElectronicsCo.

WARRANTY NOTICE

WARRANTIES: PattonElectronicsCo.(hereafterreferredtoasPatton)warrantsthatits

equipmentisfreefromanydefectsinmaterialsandworkmanship. Thewarrantyperiodshall

betwo yearsfromthe date ofshipmentof equipment. Patton’s soleobligationunder its

warrantyis limited totherepair or replacementofthe defective equipment,providedit is

returnedtoPatton,transportationprepaid,withinareasonableperiod. Thiswarrantywillnot

extendtoequipmentsubjectedtoaccident,misuse,alterationsorrepairnotmadebyPattonor

authorizedbyPattoninwriting.

PUBLICATION NOTICE

Thismanualhasbeencompiledandcheckedforaccuracy. Theinformationinthismanual

doesnotconstituteawarrantyofperformance. Pattonreservestherighttorevisethis

publicationandmakechangesfromtimetotimeinthecontentthereof. Pattonassumesno

liabilityforlossesincurredasaresultofout-of-dateorincorrectinformationcontainedinthis

manual.

(1205P)

113001UA

PATTONELECTRONICSCO. 1205P INSTALLATION AND OPERATIONS MANUAL

EMISSION REQUIREMENTS

FCC CLASS A

Warning:Changesormodificationstothisunitnotexpresslyapprovedbytheparty

responsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment.

NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassA

digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide

reasonableprotectionagainstharmfulinterferencewhentheequipmentisoperatedina

commercialenvironment.Thisequipmentgenerates,uses,andcanradiateradiofrequency

energyand,ifnotinstalledandusedin accordancewiththeinstructionmanual,maycause

harmfulinterferencetoradiocommunications.Operationofthisequipmentinaresidential

areaislikelytocauseharmfulinterferenceinwhichcasethe userwillberequiredtocorrectthe

interferenceathisownexpence.

CANADIAN EMISSIONS

This digital apparatus does not exceed the Class A limits for noise emmissions from a digital

apparatussetoutintheRadioInterferenceRegulationsoftheCanadianDepartmentof

Communications.

Lepresent appareil numerique n’emet pas debruits redioelectriques depassant les limites

applicablesauxappareils numeriques de la Class A prescites dansleReglement sur le

brouillage redioelectrique edicte par le ministere des Communications du Canada.

113001UA

iii

PATTONELECTRONICSCO. ME-V.35 INSTALLATION AND OPERATIONS MANUAL

iii

TABLE OF CONTENTS

CHAPTER 1 - OPERATION

Clocking ............................................................................................................................ 1-1

Delaying CTS .................................................................................................................... 1-1

Controlling Carrier Detect................................................................................................. 1-1

Controlling DSR ................................................................................................................ 1-2

Power ................................................................................................................................ 1-2

Approvals .......................................................................................................................... 1-2

Available Options .............................................................................................................. 1-2

CHAPTER 2 - SETUP AND INSTALLATION

Power Connection ............................................................................................................. 2-1

Factory Configuration Switch Settings .............................................................................. 2-1

Disassembly...................................................................................................................... 2-2

Installation ......................................................................................................................... 2-2

Equipment Grounding (JP4).............................................................................................. 2-2

CTS Delay, Port 1 (SW2-1,2) ............................................................................................ 2-2

CTS Delay, Port 2 (SW2-4,5) ............................................................................................ 2-3

DSR Control, Port 1 (SW1-6) ............................................................................................ 2-3

DSR Control, Port 2 (SW1-5) ............................................................................................ 2-3

DCD Control, Port 1 (SW2-6) ............................................................................................ 2-3

DCD Control, Port 2 (SW2-3) ............................................................................................ 2-3

Clock Source, Port 1 (JP6)................................................................................................ 2-3

Clock Source, Port 2 (JP5)................................................................................................ 2-4

Internal Baud Rate Selection (SW1-1,2,3,4) ..................................................................... 2-4

High Speed Option Rates (JP7,JP8,JP9,JP10) ................................................................ 2-5

Factory Test Jumpers (JP1,JP2,JP3)................................................................................ 2-5

APPENDIX

Connector Pins Used ........................................................................................................A-1

Signal Flow Diagram .........................................................................................................A-1

Strapping Guide ................................................................................................................A-2

113001UA

1-1 OPERATION

PATTONELECTRONICSCO. 1205P INSTALLATION AND OPERATIONS MANUAL

CHAPTER 1 - OPERATION

The1205P(CTSME-V.35)isa costeffective solutionforinterconnectionofV.35terminal

deviceslocated in proximity of each other. The use of two modems is eliminated with a

resultingcostsavingsto theuser. The1205P(CTSME-V.35) complieswiththe CCITTV.35

balancedinterfacespecification. Two34 pin V.35 (MR-34) connectors are provided to

interfacetotheV.35terminals.

Clocking

TheModemEliminatorcanbeeitherinternallyorexternallyclockedindependentlyoneach

Port. Ratesupto2.048Mbps areprovided bytheinternal baudrate generator. Thegenerator

willprovideclocksforbothterminalandinsurethedataissynchronizedwiththeRXClockin

bothdirections.

Delaying CTS

Request to Send (RTS) is looped back to Clear to Send (CTS) on each Port. To allow

terminalsrequiringCTSdelaystofunctionproperly,selectabledelaysofConstant,0mS,8mS

and50mS of RTS to CTSdelay is provided. Each Port ins individuallyconfigured for CTS

delay.

Controlling Carrier Detect

RTS on each port is also routed to Data Carrier Detect (DCD) on the other port. When DCD

is set to follow RTS, the same delay that is added to CTS is added to DCD. DCD can be

alsobeforcedtoconstantactivebyconfigurationswitches.

INTERNATIONAL

SERIES

1205P

PWR TD RD RTS CTS CD TXC RXC

113001UA

1-2

OPERATION

PATTONELECTRONICSCO. 1205P INSTALLATION AND OPERATIONS MANUAL

Controlling DSR

DataTerminal Ready (DTR) on each port is routed to the DataSetReady(DSR)pinof the

otherport. DSRcanbeconfigured to follow the DTR or can be forced to be activeall thetime.

Power

110or220 Volt operation is provided by a convenient switch locatedon therearpanelof the

1205P (CTS ME-V.35). Simply install the proper fuses (110VAC - .16ASB, 250V or 220VAC

-.8ASB,250V)and powerplug forthecountryofuse andselect theproperline voltageand

theunitisreadyforoperation.

Approvals

Safetyapprovals for UL & CSA havebeen granted allowing the ModemEliminator. FCC Part

15classAemissionsapprovalsinsuretheModemEliminatorwillnotinterferewithanyofthe

otherequipmentinyourdatacenter.TheModel1205PSerieshasbeentestedandfound to

complywith the limits for a Class A computing device in accordance with the specifications in

Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection from

suchinterferenceinacommercialinstallation.

CENOTICE: The CE symbol on your Patton Electronics equipment indicates that it is in

compliancewiththeElectromagneticCompatibility(EMC)directiveandtheLowVoltage

Directive (LVD) of the Union European (EU). A Certificate of Compliance is available by

contactingTechnical Support.

AvailableOptions

1205Pisavailableinbothstand-alonesubsetorrack-mountableversions(1205PRC).

Variousconfigurationsoftheinterfacearealsoavailablefromthefactory. The1205PRC fits

into the Model 1010R16 16 Card Rack Assembly.

113001UA

2-1 SETUP & INSTALLATION

PATTONELECTRONICSCO. 1205P INSTALLATION AND OPERATIONS MANUAL

Caution, Disconnect the POWER Before Removing The Cover

Vorsicht, Befor Deckung Abnehmen Mach Strom Zu.

Power Connection

Before connecting the 1205P (CTS ME-V.35) to a AC power source the top cover must be

installedand securedwiththe supplied #8-32screws. Theunit issuppliedwith a 110/

220VACvoltageswitch,turntheswitchwitha

coinor screw driver to the appropriate voltage

foryourcountry. EXAMPLE:IntheUnited

States of America; set to 110VAC. The unit is

suppliedwithaIECpowerconnectornexttothe

voltageselectswitch,plugthepowercordinto

theconnectoruntilitisfirmlyseated. Youmay

nowconnectthepowercordintoyourACoutlet.

Factory Configuration Switch Settings

The1205P (CTS ME-V.35)isconfiguredprior to shipmentwiththeswitches set tothe

followingdefaultpositions:

Switch 1 - 2 and 3 to OFF, 1, 4, 5 and 6 to ON.

Baud Rate = 64Kbps

Port 1 DSR Follows Port 2 DTR

Port 2 DSR Follows Port 1 DTR

Switch 2 - 1 and 4 to OFF, 2, 3, 5 and 6 to ON.

Port 1 CTS Delay = 0

Port 2 CTS Delay = 0

Port 1 DCD Follows Port 2 RTS

Port 2 DCD Follows Port 1 RTS

JP1 - JP3 always connected

JP4 - Open

JP5 - INTernal Clock

JP6 - INTernal Clock

HSOption

JP7 - Open

JP8 - Open

JP9 - Open

JP10 - Open

CHAPTER 2 - SETUP AND INSTALLATION

110 / 220VA Switch

Fuse Drawer

PORT 1

IEC Power Connector

110

220

100-120V

0.16ASB,250V

TO.16A,250V

200-240V

0.08ASB,250V

TO 0.08A,250V

CAUTION: FOR CONTINUED PROTECTION AGAINST RISK

FIRE, REPLACE ONLY

WITH SAME TYPE

AND RATING FUSE. ZDD JJ

BB FF LL

CC HH MM

EE KKM

B F L R V

D J N T

A E P

C H S W AA

U Y

* Switch Fuse for 100-120V (.16ASB, 250) or 200-

240V (.8ASB, 250) as noted on rear of unit.

113001UA

SETUP & INSTALLATION 2-2

PATTONELECTRONICSCO. 1205P INSTALLATION AND OPERATIONS MANUAL

Ifthe systemapplication requires oneof moreofthe default settingstobe changed,itwill be

necessarytoremovethetopcoveroftheenclosuretoaccessandchangetheDIPswitchesor

Jumperslocatedontheprintedcircuitboard.

Disassembly

Removethetopcoverbyunscrewingthephillipsheadscrewslocatedontheleftandright

sidesof the 1205P (CTS ME-V.35). The configuration switches and Jumpers are located on

thePCB as indicated on the strapping guideintheAppendixof this manual. After the switch

selectionactivityis completed,

re-install the top cover BEFORE connecting to an AC

powersource.

Installation

Selectanappropriate location accessible to and within six feetofan AC power outlet. The

outletmusthaveagroundpinreceptacleforproductwarranty.

“StraightThrough”

shielded

cables,terminatedinmaleV.35(MR-34)connectorsshouldbeusedtoconnectthetwo

terminalsto the1205P(CTS ME-V.35). Settheswitches andJumpersto matchtherequired

configurationusingthedescriptionsinthischapterandthestrappingguideintheappendix.

Equipment Grounding (JP4)

JP4providesforgroundinginterconnectioninthosesystemsrequiringaconnectionbetween

(FrameGround) and (Signal Ground).

ConnectONLYifrequired.

CTS Delay, Port 1 (SW2-1,2)

SW2position1and 2 selects RTS to CTS delay for the terminal connectedtoPORT1. RTS

(pin4) fromPORT1is loopedbacktoCTS (pin5)throughthe delaycircuitry.

SW2-1 SW2-2 DELAY

ON ON Const

OFF ON 0mS

ON OFF 8mS

OFF OFF 50mS

113001UA

2-3 SETUP & INSTALLATION

PATTONELECTRONICSCO. 1205P INSTALLATION AND OPERATIONS MANUAL

CTS Delay, Port 2 (SW2-4,5)

SW2position4and 5 selects RTS to CTS delay for the terminal connectedtoPORT2. RTS

(pin4) fromPORT2is loopedbacktoCTS (pin5)throughthe delaycircuitry.

SW2-4 SW2-5 DELAY

ON ON Const

OFF ON 0mS

ON OFF 8mS

OFF OFF 50mS

DSR Control, Port 1 (SW1-6)

SW1 position 6 selects DSR control for the terminal connected to Port 2. Set SW1 position 6

to ON to select DSR on Port 2 switching in response to DTR from Port 1 switching. Set SW1

position 6 to OFF to set DSR on Port 2 to be forced ON.

DSR Control, Port 2 (SW1-5)

SW1 position 5 selects DSR control for the terminal connected to Port 1. Set SW1 position 5

to ON to select DSR on Port 1 switching in response to DTR from Port 2 switching. Set SW1

position 5 to OFF to set DSR on Port 2 to be forced ON.

DCD Control, Port 1 (SW2-6)

SW2 position 6 selects DCD control for the terminal connected to Port 2. Set SW2 position 6

to ON to select DCD on Port 2 switching in response to RTS from Port 1 switching. Set SW2

position 6 to OFF to set DCD on Port 2 to be forced ON.

DCD Control, Port 2 (SW2-3)

SW2 position 3 selects DCD control for the terminal connected to Port 1. Set SW2 position 3

to ON to select DCD on Port 1 switching in response to RTS from Port 2 switching. Set SW2

position 3 to OFF to set DCD on Port 1 to be forced ON.

Clock Source, Port 1 (JP6)

Port 1 clock selection is accomplished via JP6. To select the internal baud rate generator as

theclocksourceinstallthejumperonthesidemarkedINT. Touseanexternalsource

provided on Port 2 Pins W & U, install the Jumper on the side marked EXT.

113001UA

SETUP & INSTALLATION 2-4

PATTONELECTRONICSCO. 1205P INSTALLATION AND OPERATIONS MANUAL

Clock Source, Port 2 (JP5)

Port 1 clock selection is accomplished via JP5. To select the internal baud rate generator as

theclocksourceinstallthejumperonthesidemarkedINT.Touseanexternalsourceprovided

on Port 1 Pins W & U, install the Jumper on the side marked EXT.

Internal Baud Rate Selection (SW1-1,2,3,4)

Selectionofinternalratesisprovidedbyconfigurationof SW1 positions 1 through 4 and JP7

throughJP10iftheHighSpeedOptionhasbeeninstalledbythefactory. Thefollowingtable

showtheratesavailable:

SW1-1 SW1-2 SW1-3 SW1-4 RATE

ON ON ON ON HS Mode

OFF ON ON ON 768K

ON OFF ON ON 384K

OFF OFF ON ON 192K

ON ON OFF ON 128K

OFF ON OFF ON 72K

ON OFF OFF ON 64K*

OFF OFF OFF ON 57.6K

ON ON ON OFF 56K

OFF ON ON OFF 48K

ON OFF ON OFF 38.4K

OFF OFF ON OFF 28.8K

ON ON OFF OFF 19.2K

OFF ON OFF OFF 14.4K

ON OFF OFF OFF 9.6K

OFF OFF OFF OFF 4.8K

* Indicates Default

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Patton electronics Modem Handbücher

Patton electronics

Patton electronics 1000P Bedienungsanleitung

Patton electronics

Patton electronics 1010B Bedienungsanleitung

Patton electronics

Patton electronics 1089/I Bedienungsanleitung

Patton electronics

Patton electronics 1200P Bedienungsanleitung

Patton electronics

Patton electronics 1058 Bedienungsanleitung

Patton electronics

Patton electronics 1058 Bedienungsanleitung

Patton electronics

Patton electronics 1226 Bedienungsanleitung

Patton electronics

Patton electronics 1089/I Bedienungsanleitung

Patton electronics

Patton electronics 1053 Bedienungsanleitung

Patton electronics

Patton electronics OnSite 1069 Bedienungsanleitung

Patton electronics

Patton electronics 1015 Bedienungsanleitung

Patton electronics

Patton electronics 1170M SERIES Bedienungsanleitung

Patton electronics

Patton electronics 1180/35 Bedienungsanleitung

Patton electronics

Patton electronics 1012B Bedienungsanleitung

Patton electronics

Patton electronics 2192 Bedienungsanleitung

Patton electronics

Patton electronics 1004 Bedienungsanleitung

Patton electronics

Patton electronics 1088/K Bedienungsanleitung

Patton electronics

Patton electronics 1180 Bedienungsanleitung

Patton electronics

Patton electronics 1058 Bedienungsanleitung

Patton electronics

Patton electronics 1089/C Bedienungsanleitung

Patton electronics

Patton electronics 1005 Bedienungsanleitung

Patton electronics

Patton electronics 1025 Bedienungsanleitung

Patton electronics

Patton electronics 1000R Bedienungsanleitung

Patton electronics

Patton electronics 2703RC Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung