Patton electronics OnSite 1052 Series Bedienungsanleitung

OnSite 1052 & 1063 Series

Metro-Optical Transport Access

Nodes

Quick Start Guide

Part Number: 07MOS10xx-QS, Rev. A

Revised: November 19, 2009

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

OnSite Series Quick Start Guide

1.0 Unpacking and Installation

Check the contents of the shipping container and accessories box or bag against the content list and the

packing slip. Verify that you received all listed equipment and inspect all items for shipping damage.

Unpack the OS-10 Series chassis and install it into a rack according to the instructions in the

OnSite Series

Getting Started Guide

on the CD-ROM shipped with your unit.

Verify that the site where you wish to install and operate the equipment conforms to the environmental

requirements in the

OnSite Series Getting Started Guide

2.0 Powering Up the System

If your OS-10 Series system was ordered for use with AC power, follow these steps:

Connect the enclosed AC power cable to the AC power receptacle on the rear side of the OS-10 Series

chassis.

Connect the power cable plug to an AC power source with the following characteristics: 15 A at 120 VAC

(60 Hz) or 10 A at 240 VAC (50 Hz) circuit with overcurrent protection.

Refer to the OS-10 Series Installation and Operation Guide if your system was ordered for use with DC power (–

48 VDC nominal).

When you ﬁrst apply power to the system, the STAT (status) LED on the front panel becomes a solid amber light.

This light indicates that the system is booting. The STAT LED becomes a solid green light when the system com-

pletes the boot process and is ready for management access and operation.

Read the safety information in the OnSite Series

Getting Started Guide

and

Administrator’s Reference Guide

thoroughly before installing and

operating your OS-10 Series system. Failure to follow this safety infor-

mation can lead to personal injury or damage to the equipment.

For your safety and to avoid damage to the equipment, follow the pre-

cautions, instructions and wiring procedures in the OnSite Series

Getting

Started Guide

before connecting the OS-10 Series system to an AC or DC

power source.

WARNING

OnSite Series Quick Start Guide

3.0 Accessing and Conﬁguring the System

To access the system management functions for the ﬁrst time, your may use either the SERIAL or the Ethernet

LAN management port. Refer to the Installation and Operation Guide for access through the SERIAL port.

For ﬁrst time access through the Ethernet LAN management port, follow these steps:

Connect a PC to the Ethernet LAN management port using the RJ-45 connector.

Conﬁgure the PC to connect to the OS-10 Series system using the factory default settings for the Ethernet

LAN management port.

Note

By default, the IP address is set to 192.168.2.100.

Launch the Web browser of your choice, and type the default IP address of the system in the Address ﬁeld

of the browser.

Note

The factory-assigned default password for the Super user is super (all lowercase letters).

Once you gain access to the system using the default settings, change the IP settings for the LAN port for secure

access to the system.

3.1 Changing the IP Settings for the LAN port

To conﬁgure the Ethernet LAN management port settings, follow these steps:

Select the SYSTEM folder from the OnSight Device Manager (DM) web-based GUI navigation menu.

From the expanded SYSTEM folder, select Management Access, and from this folder select LAN.

On the Ethernet LAN Management Port page, type the new LAN IP Address.

Note

The Admin Status for the Ethernet LAN management port is always enabled.

Click on Apply.

The new IP settings take effect once you click on the Apply button. This change in settings causes the loss of

access connectivity to the system. You can regain access immediately by typing the new IP address of the LAN

port in the Address ﬁeld of the browser. (Make sure that you change your PC settings to allow connectivity to the

OS-10 Series system over the same IP subnetwork.)

You will need to save the system conﬁguration to avoid losing the new IP settings after a subsequent reboot.

Note

The system uses the last saved conﬁguration to restore system operation and trafﬁc connectivity after

the completion of the reboot. Any recent conﬁguration data and connections not saved to the system

conﬁguration ﬁle are lost and need re-entry, if required.

OnSite Series Quick Start Guide

3.2 Saving the System Conﬁguration

To save the system conﬁguration to the ﬂash memory, follow these steps:

Select the SYSTEM folder from the OnSight DM web-based GUI navigation menu.

From the expanded SYSTEM folder, select the Actions folder.

From the expanded Actions folder, select Save Conﬁguration.

A warning window opens to alert you to the start of the save-conﬁguration process. Click on OK to continue or

Cancel to cancel the request.

4.0 Additional Information

The system is now ready for operation using the OnSight DM web-based graphical user interface (GUI). You may

now conﬁgure the system clock, timing mode and STM-1 interface settings for your intended application.

Refer to the

OnSite Series Getting Started Guide

and the

OnSite Series Administrator’s Reference Guide

located on the

CD-ROM shipped with your device

A.0 Customer and Technical Support

Online support: www

.patton.com

E-mail support:

[email protected]

—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax:

+1 (253) 663-5693

(USA)

or +41 (0)31 985 25 26 (

Switzerland)

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

Andere Handbücher für OnSite 1052 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Patton electronics Netzwerk-Hardware Handbücher

Patton electronics

Patton electronics OnSite 9100 Bedienungsanleitung

Patton electronics

Patton electronics NetLink 2720/B Bedienungsanleitung

Patton electronics

Patton electronics 2888 Bedienungsanleitung

Patton electronics

Patton electronics 3092 Bedienungsanleitung

Patton electronics

Patton electronics 450RC24 Bedienungsanleitung

Patton electronics

Patton electronics 3096RC Bedienungsanleitung

Patton electronics

Patton electronics 2720/I Series Bedienungsanleitung

Patton electronics

Patton electronics IM 1/F Bedienungsanleitung

Patton electronics

Patton electronics 2707RC Bedienungsanleitung

Patton electronics

Patton electronics NetLink 2720 Series Bedienungsanleitung

Patton electronics

Patton electronics ForeFront 6081RC EdgeRoute Benutzerhandbuch

Patton electronics

Patton electronics 2715RC Bedienungsanleitung

Patton electronics

Patton electronics ForeFront 6081RC EdgeRoute Bedienungsanleitung

Patton electronics

Patton electronics ACC-S02 Bedienungsanleitung

Patton electronics

Patton electronics NetLink 2707C Bedienungsanleitung

Patton electronics

Patton electronics 2710RC Series Bedienungsanleitung

Patton electronics

Patton electronics RocketLink-G 3088/I Bedienungsanleitung

Patton electronics

Patton electronics 3196RC Bedienungsanleitung

Patton electronics

Patton electronics 3095 Bedienungsanleitung

Patton electronics

Patton electronics 2025 Bedienungsanleitung

Patton electronics

Patton electronics 1084 Bedienungsanleitung

Patton electronics

Patton electronics RocketLink-G 3008/I Bedienungsanleitung

Patton electronics

Patton electronics 2450 Bedienungsanleitung

Patton electronics

Patton electronics RocketLink-G 3088 Series Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung