Patton electronics SMARTNODE 4900 Bedienungsanleitung

SmartNode 4900

IpChannel Bank

Quick Start Guide

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

Part Number: 07MSN4900-QS, Rev. D

Revised: February 9, 2012

Start Installation

For Quick

Start Installation

For Quick

Patton Electronics Company, Inc.

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

Tel: +1 (301) 975-1000

Fax: +1 (301) 869-9293

Support: +1 (301) 975-1007

Web: www.patton.com

E-mail: support@patton.com

Trademark Statement

Patton, the Patton logo, and SmartNode are registered trademarks of Patton Electronics

Company. The terms SmartWare and SmartView Management Center are trademarks of

Patton Electronics Company. All other trademarks presented in this document are the

property of their respective owners.

The information in this document is subject to change without notice. Patton Elec-

tronics assumes no liability for errors that may appear in this document.

In no event shall Patton Electronics or its employees and associated companies be lia-

ble for any incidental, special, indirect or consequential damages whatsoever, including

but not limited to lost profits, arising out of or related to this manual or the informa-

tion contained within it, even if Patton Electronics has been advised of, known, or

should have known, the possibility of such damages.

Important Information

To use virtual private network (VPN) and/or AES/DES/3DES encryption capabilities

with the SmartNode 4900, you may need to purchase additional licenses, hardware,

software, network connection, and/or service. Contact [email protected] or

+1 (301) 975-1000 for assistance.

Introduction 3

SmartNode 4900 Quick Start Guide

Introduction

This Quick Start Guide leads you through the basic steps to set up a new SmartNode and to download a con-

figuration. Please note that this guide does not replace the detailed SmartWare Software Configuration Guide

and the SmartNode 4900 User Manual available online at www.patton.com/manuals/SN4900.pdf.

SmartNodes can be used for a wide variety of IP and voice over IP applications. To support and ease the con-

figuration of the SmartNodes configuration templates for the most important applications are available online

at www.patton.com/voip/appnotes.asp.

Setting up a new SmartNode consists of the following steps:

1. Attach the power cable retainer clips to the unit

2. Connect a PC to the SmartNode, log in and configure your LAN IP address (see page 4 for details)

3. Connect the SmartNode to the LAN (see page 6)

4. Download a configuration example, adapt it to your network, and load it onto the SmartNode (see page 7)

Attaching the cable retainer clips

To secure the power cord, it is necessary to attach the metal retainer clips (if applicable to your model). Squeeze

the clip and insert into the holes in the screws on either side of the power connector on your unit. The clip will

pop into place.

Figure 1. Attaching the cable retainer clips

Note

Refer to the SmartNode 4900 User Manual on the Patton website for

detailed instructions about grounding and connecting power to your

unit.

For FXO (/JO) models: To maintain CE/EMC compliance,

attach the included snap-on ferrite clamp (Patton P/N 0818S-

02) to the 64/50 pin telco cable (not included but available

upon request) about four inches away from the FXO box telco

port connector.

IMPORTANT

Power cable

retainer clip

Connecting a PC, logging in, and configuring the LAN IP address 4

SmartNode 4900 Quick Start Guide

Connecting a PC, logging in, and configuring the LAN IP address

Connecting power and configuring the default IP address

Connect the SmartNode to the mains power supply using the included power supply and cable. When the

RUN LED stops blinking and remains lit, the SmartNode is ready.

The factory default IP settings are listed in table 1. If these addresses do not work with your network they must

be changed. Contact your network administrator if you are not sure which IP address to use in

your installation.

Note

The DHCP server is running on the ETH 0/1 of the SN4900 Series

models. All Ethernet ports are pre-configured and active.

Connecting to a PC and logging in

1. To access the SmartNode configuration, connect a PC equipped with an RS-232 console port to the Con-

sole port on the front of the SmartNode. Use the included black Ethernet cable and RJ45 to DB-9 adapter

for this purpose (Model 16F-561).

Figure 2. Connecting to the PC

2. Open a Terminal connection to the SmartNode. Use the Terminal program included with most PC oper-

ating systems (e.g. Hyper Terminal on Windows).

Table 1. Factory default IP address and network mask configuration

Item IP Addresss(es) Network Mask

WAN interface Ethernet 0 (ETH 0/0) DHCP DHCP

LAN interface Ethernet 1 (ETH 0/1) 192.168.1.1 255.255.255.0

DHCP server address range 192.168.1.10-192.168.1.19 255.255.255.0

100-240V

(50-60 Hz)

1 AMP

UNITEQUIPPED WITH DUAL SUPPLIES

DISCONNECTBOTH SUPPLIES

BEFORESERVICING

UNITEQUIPPED WITH DUAL SUPPLIES

DISCONNECTBOTH SUPPLIES

BEFORESERVICING

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console Telco Ports

Reset

Expansion

ETH 0/1

Status Activity

Console port

Laptop PC

Model 16F-561

adapter and cable

Connecting a PC, logging in, and configuring the LAN IP address 5

SmartNode 4900 Quick Start Guide

3. Type administrator as the login prompt and press the Enter key after the password prompt (do not type

anything for the password). A prompt will appear consisting of the IP address and >character.

password:

172.16.40.1>

4. Following log in, the SmartNode is in operator execution mode (indicated by >character in the command

line prompt). With the commands enable and configure, you enter the configuration mode.

172.16.40.1>enable

172.16.40.1#configure

172.16.40.1(cfg)#

Changing the IP address

1. Select the context IP mode to configure an IP interface.

172.16.40.1(cfg)#context ip router

172.16.40.1(ctx-ip)[router]#

2. Set the IP address and network mask for the each IP interface (eth0, for example).

Note

For the examples in this guide, a private network (172.16.1) IP

address is used.

172.16.40.1(ctx-ip)[router]#interface eth0

172.16.40.1(if-ip)[eth0]#ipaddress 172.16.1.10 255.255.255.0

2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.

2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.

172.16.1.10(if-ip)[eth0]#

3. Make this modified configuration your new start-up configuration. On the next start-up the system will

initialize itself using the modified configuration.

172.16.1.10 (if-ip)[eth0]#copy running-config startup-config

172.16.1.10 (if-ip)[eth0]#

Go to section “Connecting the SmartNode to the LAN” on page 6 to connect the SmartNode to

your network.

Connecting the SmartNode to the LAN 6

SmartNode 4900 Quick Start Guide

Connecting the SmartNode to the LAN

The 4900 Ethernet ports are auto MDX, therefore a straight-through wired cable can be used for host and

switch connections (see figure 3).

Figure 3. Connecting the SmartNode to the network

You can check the connection with the ping command to another host on the local LAN.

172.16.1.99(if-ip)[eth0]#ping <IP Address of the host>

Respectively from the host: ping 172.16.1.99

Note

To ping outside your local LAN, you will need to configure the

default gateway.

You may now start to configure the SmartNode from scratch using the CLI commands, but we recommend

that you start your configuration from a template. See “Downloading a configuration example, adapting it to

your network, and loading it onto the SmartNode” on page 7 for further details.

For a detailed description of the CLI refer to the SmartWare Software Configuration Guide (SCG) available on

online at: www.patton.com/smartnode.

100-240V

(50-60 Hz)

1 AMP

UNITEQUIPPED WITH DUAL SUPPLIES

DISCONNECTBOTH SUPPLIES

BEFORESERVICING

UNITEQUIPPED WITH DUAL SUPPLIES

DISCONNECTBOTH SUPPLIES

BEFORESERVICING

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console Telco Ports

Reset

Expansion

ETH 0/1

Status Activity

LAN (ETH 0/1)

Network

interface

PC or workstation

or Telnet

LAN

Internet or

WAN (optional)

WAN

(ETH 0/0)

Downloading a configuration example, adapting it to your network, and loading it onto the SmartNode 7

SmartNode 4900 Quick Start Guide

Downloading a configuration example, adapting it to your network,

and loading it onto the SmartNode

Patton provides a collection of configuration templates on the support page at www.patton.com/smartnode—

one of which may be similar enough to your application that you can use it to speed up configuring the Smart-

Node. Simply download the configuration note that matches your application to your PC. Adapt the configu-

ration as described in the configuration note to your network (remember to modify the IP address) and copy

the modified configuration to a TFTP server. The SmartNode can now load its configuration from this server.

Note

If your application is unique and not covered by any of Patton’s configura-

tion templates, you can manually configure the SmartNode instead of load-

ing a configuration file template. In that case, refer to the SmartWare

Software Configuration Guide for information on configuring the SmartNode

device.

In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the configuration

named SN.cfg in the root directory of the TFTP server.

172.16.1.99(if-ip)[eth0]#copy tftp://172.16.1.11/SN.cfg startup-config

Download...100%

172.16.1.99(if-ip)[eth0]#

After the SmartNode has been rebooted the new startup configuration will be activated.

172.16.1.99(if-ip)[eth0]#reload

Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-config'?

Press 'yes' to store, 'no' to drop changes : no

Press 'yes' to restart, 'no' to cancel : yes

The system is going down

Additional information

For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,

refer to the martWare Software Configuration Guide and the SmartNode 4900 User Manual on www.pat-

ton.com/smartnode.

When you issue the reload command, the SmartNode will ask

if you want to copy the running configuration to the startup con-

figuration. Since you just downloaded a configuration file to the

startup configuration you must answer this question with NO.

Otherwise, the downloaded configuration will be overwritten

and lost!

IMPORTANT

Certifications and approvals 8

SmartNode 4900 Quick Start Guide

Certifications and approvals

EC Declaration of Conformity

(see section “EG-Konformitätserklärung” for German version)

Product Description: SmartNode 4900

The products described above in the form as delivered are in conformity with the provisions of the following

European Directive:

R&TTE Directive 1999/5/EC

Guidelines of the European Parliament and the Committee for the Harmonisation of the Legal Regula-

tions of the Member States concerning radio equipment and telecommunications terminal equipment and

the mutual recognition of their conformity.

The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/

EG-Konformitätserklärung

(see section “EC Declaration of Conformity” for English version)

Produktbezeichnung: SmartNode 4900

Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften

folgender Richtlinie überein:

R&TTE 1999/5/EG

Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der Mit-

gliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige

Anerkennung ihrer Konformität.

Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/certifications/

The safety advices in the documentation accompanying the products shall be obeyed. The

conformity to the above directive is indicated by the CE sign on the device.

Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten. Die

Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem

Gerät bestätigt.

Andere Handbücher für SMARTNODE 4900

Inhaltsverzeichnis

Andere Patton electronics Netzwerk-Hardware Handbücher

Patton electronics

Patton electronics SMARTNODE 4900 Bedienungsanleitung

Patton electronics

Patton electronics OnSite 9100 Bedienungsanleitung

Patton electronics

Patton electronics OnSite 07MOS10xx-GS Bedienungsanleitung

Patton electronics

Patton electronics ForeFront 2616RC Bedienungsanleitung

Patton electronics

Patton electronics 3096RC Bedienungsanleitung

Patton electronics

Patton electronics IM 1/F Bedienungsanleitung

Patton electronics

Patton electronics 2888 Referenzhandbuch

Patton electronics

Patton electronics NetLink-E1 2715 Bedienungsanleitung

Patton electronics

Patton electronics 3060/X.21 Bedienungsanleitung

Patton electronics

Patton electronics Model 2604 Bedienungsanleitung

Patton electronics

Patton electronics ipRocketLink IAD 3086 Bedienungsanleitung

Patton electronics

Patton electronics 2784 NAU Bedienungsanleitung

Patton electronics

Patton electronics 2710RC Series Bedienungsanleitung

Patton electronics

Patton electronics ipRocketLink IAD 3086 Bedienungsanleitung

Patton electronics

Patton electronics 2025 Bedienungsanleitung

Patton electronics

Patton electronics FORESIGHT 6300 Bedienungsanleitung

Patton electronics

Patton electronics ipRocketLink IAD 3086 Bedienungsanleitung

Patton electronics

Patton electronics 3101RC Bedienungsanleitung

Patton electronics

Patton electronics NetLink 2701/B Bedienungsanleitung

Patton electronics

Patton electronics OnSite 2884 Bedienungsanleitung

Patton electronics

Patton electronics 1084 Bedienungsanleitung

Patton electronics

Patton electronics NetLink 2960 RAS Bedienungsanleitung

Patton electronics

Patton electronics 460RC Bedienungsanleitung

Patton electronics

Patton electronics Model 2604 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung