Patton electronics Patton IPLink 2603 Bedienungsanleitung

IPLink™ Model 2603 & 2620

WAN Access Router

Quick Start Guide

Document Number: 03323U7-001 Rev. B

Part Number: 07M2620-QS

Revised: October 4, 2005

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

IPLink 2603 & 2620 Quick Start Guide

1.0 Power up the router

Your router comes with one of the following power supply options:

•

External AC adaptor with included power cord

•

Internal AC power supply

•

Internal DC power supply—no power accessories are included

1.1 Models with external AC adaptor

Connect female plug of the AC power cord to the AC adaptor provided.

Connect the barrel-type connector of the AC adaptor to the barrel-type

Power

jack on the IPLink router.

Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC).

1.2 Models with internal AC power supply

Insert the female end of the AC power cord into the internal power supply connector.

Connect the male end of the power cord into an AC power outlet (100–240 VAC).

• The IPLink 2603/2620 contains no user serviceable parts. The equip-

ment shall be returned to Patton Electronics for repairs, or repaired

by qualiﬁed service personnel.

• An approved external power supply that incorporates a disconnect

device shall be used and positioned within easy reach of the operator.

• For AC powered units, the power cable used to connect the power

supply shall meet all applicable standards for the country in which it

is to be installed, and be connected to a wall outlet which has

earth ground.

• Hazardous network voltages are present in WAN ports regardless of

whether power to the unit is ON or OFF. To avoid electric shock, use

caution when near WAN ports. When detaching the cables, detach the

end away from the 2603/2620 ﬁrst.

• Do not work on the system or connect or disconnect cables during

periods of lightning activity.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, ﬂam-

mability, and mechanical serviceability.

WARNING

CAUTION

IPLink 2603 & 2620 Quick Start Guide

1.3 Models with internal DC power supply

Strip insulation 1/4-inch from the electrical wires that will connect the DC power source to the IPLink.

Connect the ground terminal from the power source to the ground terminal on the IPLink.

Connect the negative (-) terminal from the power source with to the negative (-) terminal on the IPLink.

Connect the positive (+) terminal from the power source with to the positive (+) terminal on the IPLink.

1.4 Power-up indication

The

Power

LED blinks as the IPLink is powering up. When the

Power

LED stops blinking and remains lit, the

IPLink is ready for you to conﬁgure.

2.0 Conﬁgure the IP address

The IPLink is shipped with a factory-conﬁgured IP address assigned to the

Ethernet

LAN port (green outline). The

address is

192.168.200.10/24

. In most cases, you must change the address to be on the same subnet as your

PC, as described in the procedures below. If you are not sure which IP address to use for your installation, contact

your network administrator.

2.1 Connecting a PC and logging in

Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port

to the IPLink’s

Console

port (see

ﬁgure 1

Figure 1.

Connecting IPLink to the PC’s serial port

Start a HyperTerminal session on the PC using the settings:

9600 bps, 8 data bits, 1 stop bit, no parity, no ﬂow control

superuser

Password: superuser

Link

Frame

Link

100M

TxRx

WAN Ethernet

Power

Console

ipLink Gateway

High Speed WAN Access Router

Model 2603

Connect to Console port

Serial port

PC with

terminal emulator

IPLink 2603 & 2620 Quick Start Guide

2.2 Modifying the IP address

Display current IP interface settings for the IPLink

Ethernet

LAN port.

→→

ip list interfaces <enter>

IP Interfaces:

ID | Name | IP Address | DHCP | Transport

---|------|----------------|----------|--------------

1 | ip1 | 192.168.200.10 | disabled | <eth1>

----------------------------------------------

------

Modify the IP address for the LAN port according to your network requirements.

→→

ip set interface ip1 ipaddress 10.10.10.5 255.255.255.0

Note

The above IP address (

10.10.10.5/24)

is only an example. You must choose an IP address on the same

subnet as your PC

Verify the new address is correct and save it in system boot memory.

→→

ip list interfaces <enter>

→→

system config save <enter>

→→

Now you can connect the IPLink to your local IP network and complete the remaining conﬁguration from your

PC using a standard web browser.

3.0 Connect to the local IP network

Connect the IPLink’s (green)

Ethernet

port to the same Ethernet segment as your PC (see

ﬁgure 2

Note

The Model 2620 does not have an MDI-X switch, so you must use a cable wired straight-through to con-

nect the Model 2620’s Ethernet port to the IP network.

If you have a Model 2603, press the MDI-X switch until the

Ethernet Link

LED turns on.

Figure 2.

Connecting the IPLink to the local IP network (Model 2603/K shown)

Crossover

10/100

Ethernet WAN

Power MDI-X

RX TX

Connect to Ethernet port

Ethernet port

MDI-X switch

IPLink 2603 & 2620 Quick Start Guide

You can check the network connection with the ping command. For example, you would ping

10.10.10.5

from

your PC.

4.0 Log onto the web management interface

You will now access the web management Graphical User Interface (GUI) to conﬁgure the IPLink using a stan-

dard web browser (such as Internet Explorer or Netscape browser).

At your PC, open a web browser and enter the IP address you assigned to the IPLink’s Ethernet LAN port

in step 2 of section

2.2 “Modifying the IP address”

on page 4.

superuser

and the password

superuser

Figure 3.

IPLink web management home page

Now you can use the IPLink’s web management pages to complete your conﬁguration (see section

6.0

“Complete the installation”

on page 6).

5.0 Connect the WAN port

The IPLink 2603/T, 2603/K, and 2620 come with a T1/E1 WAN interface (presented on an RJ-48C connector

with selectable line impedances of 100-ohms for T1 and 120-ohms for E1 lines). The Model 2603 has one RJ-

48C connector and the 2620 has two. The Model 2603/K and 2620/KK also come with dual BNC connectors for

alternate connection to unbalanced 75-ohm E1 lines.

To connect the WAN port on a Model 2620 or Model 2603/T, or if you plan to use the RJ-48C port on a 2603/K,

refer to section “Connecting to the RJ-48C WAN port”. Otherwise, refer to section “Connecting to the unbalanced

75-ohm TX and RX WAN ports (Model 2603/K and 2620/KK only)” to install cables onto the BNC connectors on

the 2603/K and 2620/KK models.

IPLink 2603 & 2620 Quick Start Guide

Connecting to the RJ-48C WAN port

Obtain a twisted-pair cable with an RJ-48C plug connector at each end.

Plug one end of the cable into the RJ-48C socket (labeled

WAN

)

on the IPLink Router.

Plug the other end of the cable into the T1/E1 device.

Repeat steps 1 through 3 to install the remaining WAN cables on a Model 2620

Connecting to the unbalanced 75-ohm TX and RX WAN ports (Model 2603/K

and 2620/KK only)

Obtain a coaxial cable with a BNC connector at each end.

Plug one end of the cable into the transmit socket (labeled

)

on the IPLink Router. Plug the other end

of the cable into the receive port of the E1 device.

Plug one end of the cable into the receive socket (labeled

)

on the IPLink Router. Plug the other end of

the cable into the transmit port of the E1 device.

6.0 Complete the installation

To ﬁnish conﬁguring your IPLink, and for detailed information about installing, conﬁguring, operating, and trou-

bleshooting, refer to the

Models 2603, 2621, and 2635 IPLink Series High Speed Routers User Guide

and appli-

cation notes, available on the enclosed Patton CD-ROM or at

www.patton.com.

A.0 Customer and Technical Support

Toll-Free VoIP support: call

sip:[email protected]

with a VoIP SIP phone

Online support: www

.patton.com

E-mail support:

[email protected]

—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax:

+1 (253) 663-5693

(USA)

or +41 (0)31 985 25 26 (

Switzerland)

IPLink 2603 & 2620 Quick Start Guide

B.0 Compliance Information

B.1 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in

strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-

tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-

dance with the speciﬁcations in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable

protection from such interference in a commercial installation. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception,

which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

B.2 EC Declaration of Conformity

Product Description:

IPLink 2603, 2620

We certify that the apparatus identiﬁed above conforms to the requirements of Council Directive 1999/5/EC on

the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equip-

ment and the mutual recognition of their conformity.

The signed Declaration of Conformity can be downloaded from

www.patton.com/certiﬁcations/

B.3 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of

this equipment is a label that contains—among other information—a product identiﬁer in the format US:

AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the

applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-

pany will notify the customer as soon as possible. Also, you will be advised of your right to ﬁle a complaint with

the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens, the telephone company will provide advance notice in

order for you to make necessary modiﬁcations to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If

the equipment is causing harm to the telephone network, the telephone company may request that you discon-

nect the equipment until the problem is resolved.

The safety advises in the documentation accompanying the products shall be obeyed. The

conformity to the above directive is indicated by the CE sign on the device.

IPLink 2603 & 2620 Quick Start Guide

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-

vice commission or corporation commission for information.

B.4 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Speciﬁcations. This is con-

ﬁrmed by the registration number. The abbreviation, IC, before the registration number signiﬁes that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical

speciﬁcations were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company’s inside wiring associated with a single line individual service

may be extended by means of a certiﬁed connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certiﬁed equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term

IPLink

is a trademark of Patton Electronics Company. All other trademarks presented in this document

are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the

Models 2603, 2621, and 2635 IPLink Series

High Speed Routers User Guide

located on the CD-ROM that came with your router or available online

www.patton.com

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

Andere Handbücher für Patton IPLink 2603

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Patton electronics Netzwerk-Router Handbücher

Patton electronics

Patton electronics IPLink 2803 Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4960 Series Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4960 Series Bedienungsanleitung

Patton electronics

Patton electronics 3087 Bedienungsanleitung

Patton electronics

Patton electronics IPLink 2821 Bedienungsanleitung

Patton electronics

Patton electronics IM 1/I Bedienungsanleitung

Patton electronics

Patton electronics 3224 Diamond Edge Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4520 Series Bedienungsanleitung

Patton electronics

Patton electronics 3210 Bedienungsanleitung

Patton electronics

Patton electronics OnSite 3210 Series Bedienungsanleitung

Patton electronics

Patton electronics SmartNode 4520 Series Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4552 Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4630 Series Bedienungsanleitung

Patton electronics

Patton electronics IM1/I4 Bedienungsanleitung

Patton electronics

Patton electronics IM2RC/I-100B Bedienungsanleitung

Patton electronics

Patton electronics 4110 Series Bedienungsanleitung

Patton electronics

Patton electronics SMARTNODE 4630 Series Bedienungsanleitung

Patton electronics

Patton electronics Patton IPLink 2635 Bedienungsanleitung

Patton electronics

Patton electronics Patton IPLink 2603 Bedienungsanleitung

Patton electronics

Patton electronics PASSERELLES ROUTEURS VOIP 455X Konfigurationshandbuch

Patton electronics

Patton electronics DIAMONDLINK 3201 Bedienungsanleitung

Patton electronics

Patton electronics IM2RC/IA Bedienungsanleitung

Patton electronics

Patton electronics SmartLink 4020 Series Bedienungsanleitung

Patton electronics

Patton electronics 3060/V24 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung