Patton electronics 531 Bedienungsanleitung

USER

MANUAL

MODEL 531

Ethernet (ThinNet)

Surge Protectors

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part# 07M531-B

Doc# 074051UB

Revised 12/18/96

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected and tested and is

warranted for One Year parts and labor. If any questions arise during

installation or use of the unit, contact Patton Electronics Technical

Support: (301) 975-1007; http://www.patton.com; or,

[email protected].

2.1 FEATURES

• Can handle large surges caused by storms, power outages, etc.

• Conforms to the IEEE 802.3 specification

• Provides separate connection to chassis ground for surge handling

• Easy to install

• Made in the U.S.A

2.2 DESCRIPTION

LANs are naturally susceptible to a host of lethal transient

voltages, according to the IEEE 802.3 specification (see paragraph

8.7.2). That's why we designed the Model 531 series LAN surge

protectors.

The Model 531 connects directly between incoming ThinNet data

cables and LAN I/O ports. By shunting all threatening voltages to the

chassis ground, the Model 531 ensures the integrity of the data in your

LAN and protects connected equipment from lightning induced

energies, AC power induction, electrostatic discharges and ground

potential differences.

Warning: This product will not provide complete protection should your

equipment or building be subject to a direct lightening hit.

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 531 components to be free

from defects, and will—at our option—repair or replace the product

should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials, and

does not cover customer damage, abuse or unauthorized modification.

If this product fails or does not perform as warranted, your sole

recourse shall be repair or replacement as described above. Under no

condition shall Patton Electronics be liable for any damages incurred

by the use of this product. These damages include, but are not limited

to, the following: lost profits, lost savings and incidental or

consequential damages arising from the use of or inability to use this

product. Patton Electronics specifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall be

deemed an acceptance of these terms by the user.

1.2 SERVICE

All warranty and nonwarranty repairs must be returned freight

prepaid and insured to Patton Electronics. All returns must have a

Return Materials Authorization number on the outside of the shipping

container. This number may be obtained from Patton Electronics

Technical Support: (301) 975-1007. Notice: Packages received without

an RMA number will not be accepted.

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Patton Model Patton Model 531. Technical Service hours: 8AM to

5PM EST, Monday through Friday.

3. Connect the braided ground strap directly to a frame ground

connection on the protected device. If you are unsure where to

locate a frame ground connection on your equipment, consult the

equipment’s user manual or contact the manufacturer - the ground

connection is critical for proper operation.

Coaxial input

from Network

Connection to

frame ground

Coaxial input from

Network

Model 531 ThinNet

Surge Protector

3.0 INSTALLATION

Patton's Model 531 units are easy to install and should give you years

of trouble-free service. Here are a few simple instructions to help you

get things hooked up right:

Standard Model 531 MF:

1. Unplug (disconnect) the existing connection between the coaxial

cable and the equipment I/O port.

2. Install the Model 531 between the incoming coax line and the

protected equipment (see below). Place the surge protector as

close as possible to the device being protected.

3. Connect the braided ground strap directly to a frame ground

connection on the protected device. If you are unsure where to

locate a frame ground connection on your equipment, consult the

equipment's user manual or contact the manufacturer—the ground

connection is critical for proper operation of the Model 531.

T-Splitter Model 531 MFF:

1. Remove the existing T-splitter from the Network Interface Card and

disconnect the coaxial cables.

2. Install the Model 531 directly on the Network Interface Card and

reattach the coaxial cables.

Coaxial input from

Network

Output to protected

equipment

Connection to frame

ground

Model 531 ThinNet

Surge Protector

APPENDIX A

PATTON MODEL 531 SPECIFICATIONS

Interface: Ethernet (IEEE 802.3, ThinNet) BNC coaxial

Size: 2.0" long x 1.0" diameter

Circuit: Bipolar, solid state protection on BNC

connectors

Response Time: Less than 5 nanoseconds.

Input Capacitance: 18 pF

Clamp Voltage: 25 volts at 100A (8/20 µ waveform )

Surge Capacity: 400A (8/20 µ waveform )

Energy Handling: 1.5 Kilowatts per wire

Transfer Loss: -.05dB at 100 MHz

Return Loss: -17dB @ 100MHz

Group Delay: None, 1 MHz to 100 MHz

Series Resistance: None

Max Signal Rate: > 10 Mbps

Grounding: External connection provides separate unit-

ground to chassis-ground contact

Operational/Storage

Temperature: -55 to +100°C

Patton Electronics Company

Andere Patton electronics Überspannungsschutz Handbücher

Patton electronics

Patton electronics 515 Bedienungsanleitung

Patton electronics

Patton electronics 537 Bedienungsanleitung

Patton electronics

Patton electronics 540 Bedienungsanleitung

Patton electronics

Patton electronics 515 DB-15 Bedienungsanleitung

Patton electronics

Patton electronics 536S Bedienungsanleitung

Patton electronics

Patton electronics 501LC Bedienungsanleitung

Patton electronics

Patton electronics 546 Bedienungsanleitung

Patton electronics

Patton electronics 574 Bedienungsanleitung

Patton electronics

Patton electronics 503S Bedienungsanleitung

Patton electronics

Patton electronics 574 Bedienungsanleitung

Patton electronics

Patton electronics 545 Bedienungsanleitung

Patton electronics

Patton electronics 570 Bedienungsanleitung

Patton electronics

Patton electronics 56X Series Bedienungsanleitung

Patton electronics

Patton electronics 509/25 Bedienungsanleitung

Patton electronics

Patton electronics 532S Bedienungsanleitung

Patton electronics

Patton electronics 510 Bedienungsanleitung

Patton electronics

Patton electronics 570-R8 Bedienungsanleitung

Patton electronics

Patton electronics 500 Bedienungsanleitung

Patton electronics

Patton electronics 51X Series Bedienungsanleitung

Patton electronics

Patton electronics 535 Bedienungsanleitung

Patton electronics

Patton electronics 533 Bedienungsanleitung

Patton electronics

Patton electronics 506 Bedienungsanleitung

Patton electronics

Patton electronics 52X Bedienungsanleitung

Patton electronics

Patton electronics 550 Series Bedienungsanleitung

Beliebte Überspannungsschutz Handbücher anderer Marken

ELAC

ELAC ProteK PR91-W Bedienungsanleitung

Tsubaki

Tsubaki TSM4000M1 Bedienungsanleitung

QVS

QVS PP134C Bedienungsanleitung

CyberPower

CyberPower CSP604T Bedienungsanleitung

Davis Instruments

Davis Instruments Radio Surge Protector Bedienungsanleitung

M-system

M-system MGA-100 Bedienungsanleitung

CyberPower

CyberPower CSP706T Bedienungsanleitung

CyberPower

CyberPower B300WRC1 Bedienungsanleitung

M-system

M-system MGD-24 Bedienungsanleitung

Leviton

Leviton 51120-3R Bedienungsanleitung

Panamax

Panamax MAX 5400-EX Bedienungsanleitung

CyberPower

CyberPower B1006T Bedienungsanleitung

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Bedienungsanleitung

Minuteman

Minuteman MMS7120RCT Bedienungsanleitung

Leviton

Leviton 52412-DS3 Bedienungsanleitung

Savio

Savio LZ-07 Bedienungsanleitung

Siemens

Siemens HNM3M120 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung