Patton CopperLink 1101E/IP67 Bedienungsanleitung

CopperLink™ Model 1101E/IP67

Outdoor Rated

Power over Ethernet Extender

Quick Start Guide

Important—This is a Class A device and is intended for use in a light

industrial environment. It is not intended nor approved for use in

an industrial or residential environment.

Part Number: 07MCL1101E_IP67-QS, Rev. A

Revised: February 17, 2017

Additional Information:

http://www.patton.com/manuals/CL1101-UM.pdf

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

Web: www.patton.com

2CopperLink 1101E/IP67 Quick Start Guide

•This device contains no user serviceable parts. The

equipment shall be returned to Patton Electronics for

repairs, or repaired by qualified service personnel.

•The external power adapter shall be a listed Limited

Power Source. The mains outlet that is utilized to power

the devise shall be within 10 feet (3 meters) of the

device, shall be easily accessible, and protected by a

circuit breaker.

•If an AC power adapter is used, ensure that the power

cable used meets all applicable standards for the coun-

try in which it is to be installed, and that it is connected

to a wall outlet which has earth ground.

•Hazardous network voltages are present in WAN ports

regardless of whether power to the unit is ON or OFF. To

avoid electric shock, use caution when near WAN ports.

When detaching the cables, detach the end away from

the device first.

•Do not work on the system or connect or disconnect

cables during periods of lightning activity.

SPECIAL CONDITION FOR SAFE USE

Ambient temperature: This unit is designed for use in

extreme ambient temperature: -14 to 158°F (-10 to 70°C).

Restricted Access: The surface of this unit can exceed

100°C under extreme ambient conditions and should be

installed in restricted locations only.

WARNING

CAUTION

CopperLink 1101E/IP67 Quick Start Guide 3

1.0 Introduction

The CopperLink Model 1101E/IP67 is an Outdoor Rated Ethernet Extender. The

CL1101E/IP67, works in pairs (one Local CL1101E/IP67 to one Remote CL1101E/IP67)

to extend Ethernet over twisted pair or Coax. The Local unit resides where a power

source is available, the Remote unit resides by the PoE end point. All CL1101E/IP67

models are interoperable with each other. For example: a CL1101E/IP67 (indoor) local

unit can connect to a CL1101E/IP67 (remote). In fact, this would be a typical use case.

The CopperLink Model 1101E/IP67 is IP67 rated. This means that it meets level 6 for

solid object protection (dust proof) and level 7 for liquid ingress (can be fully sub-

mersed at water 15 cm to 1 m deep for a period of up to 30 minutes.

Figure 1. CL1101E/IP67 Ethernet Extender application

If you will be installing a Local CL11O1E/IP67, go to section 2.0 “Planning the Local

CL1101E/IP67 Installation” on page 4. Otherwise, to install a Remote CL1101E/IP67,

go to section 3.0 “Planning the Remote CL1101E/IP67 Installation” on page 5.

4CopperLink 1101E/IP67 Quick Start Guide

2.0 Planning the Local CL1101E/IP67 Installation

To install the Local CL1101E/IP67 Ethernet Extender (see figure 2), do the following:

Figure 2. Local CL1101E/IP67 LED and ports

1. Connect a data & power cable to the Line interface (see section 4.0 “Connecting

the Line Interface” on page 6).

2. Connect an Ethernet cable to the Ethernet interface (see section 5.0 “Connecting

the 10/100Base-T Ethernet Interface” on page 8).

3. Connect the power supply cable to the Power port (see section 7.0 “Connecting

power to the Local unit” on page 10).

4. Configuring the DIP switch (see section 8.0 “Configuring the DIP Switch” on

page 11).

The interconnecting cables shall be acceptable for external use and

shall be rated for the proper application with respect to voltage, cur-

rent, anticipated temperature, flammability, and mechanical ser-

viceability.

To maintain IP67 performance, the cable glands provided on our

standard unit are for wire diameters ranging from 0.157 inch [4 mm]

to 0.252 inch [6.4 mm]. If your cables do not fit these specifications,

contact support@patton.com before using them outdoors.

CAUTION

CopperLink 1101E/IP67 Quick Start Guide 5

3.0 Planning the Remote CL1101E/IP67 Installation

To install the Remote CL1101E/IP67 Ethernet Extender (see figure 3), do the following:

Figure 3. Remote CL1101E/IP67 LED and ports

1. Connect a data & power cable to the Line interface (see section 4.0 “Connecting

the Line Interface” on page 6).

2. Connect an Ethernet cable to the Ethernet interface (see section 5.0 “Connecting

the 10/100Base-T Ethernet Interface” on page 8).

3. Connect a ground wire to the grounding screw (see section 6.0 “Connecting to the

grounding screw on the Remote unit” on page 10).

4. Configuring the DIP switch (see section 8.0 “Configuring the DIP Switch” on

page 11).

The interconnecting cables shall be acceptable for external use and

shall be rated for the proper application with respect to voltage, cur-

rent, anticipated temperature, flammability, and mechanical ser-

viceability.

To maintain IP67 performance, the cable glands provided on our

standard unit are for wire diameters ranging from 0.157 inch [4 mm]

to 0.252 inch [6.4 mm]. If your cables do not fit these specifications,

contact [email protected] before using them outdoors.

CAUTION

6CopperLink 1101E/IP67 Quick Start Guide

4.0 Connecting the Line Interface

Note The CL1101E/IP67 Ethernet Extenders work in pairs (a Local unit con-

nects to a Remote unit).

Note Actual distance and link performance may vary depending on the envi-

ronment and type/gauge of wire used.

Do the following to connect the Line interface.

1. Remove the top panel screws by turning them counter-clockwise (see Figure 4.

“Removing the top cover” on page 6).

Figure 4. Removing the top cover

2. Loosen the IP67 cable glands by turning them counter clockwise. (For the Local

unit, see figure 5 on page 7. For the Remote unit, see figure 6 on page 7).

The interconnecting cables shall be acceptable for external use

and shall be rated for the proper application with respect to volt-

age, current, anticipated temperature, flammability, and

mechanical serviceability.

Power is NOT transmitted as on traditional PoE. PoE pin-out

assumes that the same polarity is on a single pair of wires, but

in order to accommodate 1 pair mode, the polarity is alternated

within the pair.

Never connect the Line interface to a PoE port because equip-

ment damage may occur.

CAUTION

IMPORTANT

CAUTION

CopperLink 1101E/IP67 Quick Start Guide 7

Figure 5. Local unit cable glands

Figure 6. Remote unit cable glands

3. Run an un-terminated data/line cable through the gland labeled Line.

8CopperLink 1101E/IP67 Quick Start Guide

4. The CL1101E/IP67 is equipped with an RJ-45 interface jack. Terminate the cable

with an RJ-45 connector (see figure 7 for pin-out diagram).

Figure 7. RJ-45 pin-out

5. The RJ-45 connector on the CL1101E/IP67’s twisted pair interface is polarity

insensitive, and is wired for two, four, six or eight wires—pin-out to TIA/EIA

T568A/B (see table 1 on page 8).

Note 2-wire mode—non-standard pin-out

4-wire mode—802.3i/802.3u wired compatible pin-out

8-wire mode—802.3ab/802.3an wired compatible pin-out

5.0 Connecting the 10/100Base-T Ethernet Interface

Do the following to connect the 10/100Base-T Ethernet interface:

1. Run an un-terminated Ethernet cable through the gland marked Ethernet.

2. Terminate the cable with an RJ-45 connector. The RJ-45 Ethernet port is an Auto-

MDIX 10/100Base-T that connects to a 10/100Base-T device or network. Figure 8

Table 1. RJ-45 wire modes

Pair Pin Voltage

1+ 3 +

1- 6 –

2+ 1 +

2- 2 –

3+ 4 +

3- 5 –

4+ 7 +

4- 8 –

CopperLink 1101E/IP67 Quick Start Guide 9

on page 9 shows the signal/pin relationships on this interface. You may connect

this port to a hub or PC using a straight-through or crossover cable (see

Appendix 2 on page 9) that is up to 328 ft long.

Figure 8. CL1101E/IP67 10/100Base-T RJ-45 Connector Pin-out

Note Mode A and Mode B are not configurable, the remote unit requires dif-

ferent hardware.

For Mode Aorder:

•CL1101/PAFA/x/EUI-2PK (Ethernet Extender Kit)

•CL1101/PAFA/x/EUI (Remote PoE Extender)

For Mode Border:

•CL1101/PAFB/x/EUI-2PK (Ethernet Extender Kit)

•CL1101/PAFB/x/EUI (Remote PoE Extender)

The interconnecting cables shall be acceptable for external use

and shall be rated for the proper application with respect to volt-

age, current, anticipated temperature, flammability, and

mechanical serviceability.

Table 2. RJ-45 wire modes

Pin Voltage Function

1Mode A + Tx +

2Mode A + Tx –

3Mode A – Rx +

4Mode B +* N/A

5Mode B +* N/A

6Mode A – Rx –

7Mode B –* N/A

8Mode B –* N/A

CAUTION

10 CopperLink 1101E/IP67 Quick Start Guide

6.0 Connecting to the grounding screw on the Remote unit

As a standard safety practice, the chassis of the CL1101E/IP67 must be properly

grounded to protect against any contact with an electrical fault condition.

Do the following to connect to the CL1101E/IP67 to ground:

1. Run an un-terminated ground cable through the gland labeled with a ground sym-

bol (see figure 3 on page 5).

2. Terminate the cable with the spade lug provided with the unit or your own terminal.

3. Remove the grounding screw (see figure 6 on page 7).

4. Attach the ground cable to the steel plate using the grounding screw.

5. Connect the other end of the ground wire to an electrical ground nearest the

CL1101E/IP67. Often this will be on an electrical panel or sub panel. If you cannot

locate a nearby electrical ground, contact Patton Technical Support at (301) 975-

1000 to discuss an alternative grounding solution.

Note Keep the length of the ground wire as short as possible.

6. Verify that the resistance of the ground path is less than 0.5 ohms.

7.0 Connecting power to the Local unit

Note The Local CL1101E/IP67 does not have a power switch, so it powers up

as soon as it is connected to a power source.

An external AC to DC adapter is supplied with the units. No configuration is necessary

for the power supply.

Note DC power must meet the following requirements; DC power supplied

must be regulated 12 VDC ±5% to 54 VDC ±5%.

Do the following to connect the power cable to the Local unit:

1. Run an un-terminated power cable through the gland labeled Power (see figure 5

on page 7).

2. Connect the cable wires to the terminal block shown in figure 5. Be sure to match

the cable wires polarity with that of the terminal block.

The interconnecting cables shall be acceptable for external use

and shall be rated for the proper application with respect to volt-

age, current, anticipated temperature, flammability, and

mechanical serviceability.

CAUTION

Inhaltsverzeichnis

Andere Patton Extender Handbücher

Patton

Patton CopperLink 1314R Bedienungsanleitung

Patton

Patton CopperLink 1314MDE Bedienungsanleitung

Patton

Patton CopperLink CL1300 Bedienungsanleitung

Patton

Patton SmartNode 2290 Series Bedienungsanleitung

Patton

Patton 2158 Bedienungsanleitung

Patton

Patton CopperLink CL2300 Bedienungsanleitung

Patton

Patton CopperLink 1314R Bedienungsanleitung

Patton

Patton CopperLink 1314R Bedienungsanleitung

Patton

Patton SmartNode 2290 Series Bedienungsanleitung

Patton

Patton CopperLink CL2300 Bedienungsanleitung

Patton

Patton SmartNode 2290 Series Bedienungsanleitung

Patton

Patton CopperLINK 2174 Bedienungsanleitung

Patton

Patton 2168 Bedienungsanleitung

Patton

Patton CopperLink CL1300 Bedienungsanleitung

Patton

Patton CopperLink 1214E Bedienungsanleitung

Patton

Patton CopperLink 1214E Bedienungsanleitung

Patton

Patton CopperLink CL1211E Bedienungsanleitung

Patton

Patton CopperLink 1314 Bedienungsanleitung

Patton

Patton SmartNode 4830 Series Bedienungsanleitung

Patton

Patton CopperLink 1211 Bedienungsanleitung

Patton

Patton copperlink 1101 Bedienungsanleitung

Patton

Patton CopperLink E2168A Bedienungsanleitung

Patton

Patton CopperLink 1300R Bedienungsanleitung

Patton

Patton 1052AS Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung