Patton CopperLink CL2300 Bedienungsanleitung

CopperLink™ Model CL2300

Long Range Ethernet Extender

Quick Start Guide

Important—This is a Class A device and is intended for use in a light indus-

trial environment. It is not intended nor approved for use in an industrial or res-

idential environment.

Part Number: 07MCL2300-QS, Rev. B

Revised: May 17, 2018

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

Web: www.patton.com

2CopperLink CL2300 Quick Start Guide

1.0 Hardware Installation

1.1 Contents of Package

•CL2300 Long Range Ethernet Extender

•External power supply for CopperLink Model CL2300

•Ethernet cable with RJ45 plugs on each end (included)

1.2 What you will need

•Default IP address: 192.168.200.10

•Default username: admin

•Default password: (no password)

•PC Computer

•This device contains no user serviceable parts. The

equipment shall be returned to Patton Electronics for

repairs, or repaired by qualified service personnel.

•The external power adapter shall be a listed Limited

Power Source. The mains outlet that is utilized to power

the devise shall be within 10 feet (3 meters) of the

device, shall be easily accessible, and protected by a

circuit breaker.

•If an AC power adapter is used, ensure that the power

cable used meets all applicable standards for the coun-

try in which it is to be installed, and that it is connected

to a wall outlet which has earth ground.

•Hazardous network voltages are present in WAN ports

regardless of whether power to the unit is ON or OFF. To

avoid electric shock, use caution when near WAN ports.

When detaching the cables, detach the end away from

the device first.

•Do not work on the system or connect or disconnect

cables during periods of lightning activity.

WARNING

CopperLink CL2300 Quick Start Guide 3

1.3 Identify the connector and attach the cables

All connectors are on the rear panel of the CL2300 Ethernet Extender (see figure 1).

Figure 1. CL2300 Ethernet Extender rear panel

Connect the Line Interface

To function properly, the CL2300 must be connected using a twisted-pair, uncondi-

tioned, dry, metal wire, between 19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that

run through signal equalization equipment are not acceptable.

The Ethernet Extender is equipped with a RJ-45 interface jack (Line), which conforms

to the T568B standard. As such, any standard Category 5e cable can be used to directly

connect two extenders. Depending on the extender model, it will have a two-wire, four-

wire or eight-wire interface.

Observe the signal/pin relationship on the CL2300’s Line interface jack for each pair in

Figure 2.

Figure 2. CL2300 (RJ-45) twisted pair line interface

4CopperLink CL2300 Quick Start Guide

Figure 3 shows the proper way to wire a cable with a RJ-45 jack on one end and four

RJ-11jacks on the other (see figure 4).

Figure 3. Pinout for two devices

Figure 4. RJ-45 to RJ-11 cable

2.0 Connecting Interfaces

2.1 Connecting Console Interface

Install the supplied RJ-45-to-RJ-45 cable with the DB9-RJ45 adapter between the

CL2300 RS-232 port and an open serial port on your computer. If you need to assem-

ble your own cable, refer to the pinout diagram in figure 5 on page 5.

CopperLink CL2300 Quick Start Guide 5

Figure 5. DB-9-to-RJ-45 cable diagram

2.2 Connect the Ethernet Interface

The Long Range Ethernet Extender has four unshielded RJ-45 auto-MDIX10/100Base-T

interfaces. These are designed to connect directly to a 10/100Base-TX network.

Figure 6 shows the signal/pin relationships on this interface. You may connect this port

to a hub or PC using a straight-through or crossover cable that is up to 328 ft long.

‘

Figure 6. OS330010/100Base-T RJ-45 Connector Pinout

2.3 Connect the Power Source

The Long Range Ethernet Extender does not have a power switch, so it powers up as

soon as it is plugged in.

The power connection is made via the barrel jack on the rear panel of the CL2300. No

configuration is necessary for the power supply.

2.4 Ethernet Extender Status LEDs

The LEDs indicate the status of power, the WAN (CopperLink), and Ethernet connec-

tions.

1 TX+ (data output)

2 TX- (data output)

3 RX+ (data input)

4 (no connection)

5 (no connection)

6 RX- (data input)

7 (no connection)

8 (no connection)

6CopperLink CL2300 Quick Start Guide

Note When extinguished, the LED indicators are clear; when lit, they shine a brilliant

yellow.

Figure 7. CL2300 front panel

3.0 CLI Operation and Configuration

You can connect a PC to configure the CopperLink CL2300 using the CLI.

3.1 Connect with SSH

1. Connect the Ethernet cable.

2. Connect the power supply.

3. Connect via SSH to the default address 192.168.200.10

4. Login with the default username admin and no password.

3.2 Connect with Console

1. Connect the RS232 Console cable.

Table 1. CL2300 front panel LEDs

LED Name LED Function Description

Power ON Indicates power is applied.

CPE OFF

CopperLink (WAN) is configured as Local

CopperLink (WAN) is configured as Remote.

CopperLink Pair

(one LEAD for each

port [1 on 3301, 2

on 3302, 4 on

3304])

OFF

SLOW BLINK

FAST BLINK

Port is configured as DOWN.

Port is in data mode.

Port is in handshake mode (looking for a

remote signal).

Port is in training mode (active communication

with remote).

Ethernet

(0/0 - 0/3)

OFF

Port is linked.

Data is passing over the port.

CopperLink CL2300 Quick Start Guide 7

2. Connect the power supply.

3. Login with the default username admin and no password.

3.3 Change the IP address (default: 192.168.200.10)

Follow the command sequence below.

node~>enable

node~#configure

node~(cfg)#context ip ROUTER

node~(ctx-ip)[router]#interface LAN

node~(if-ip)[router.LAN]#no ipaddress 192.168.200.10/24

node~(if-ip)[router.LAN]#ipaddress <new address>/<new

mask>

3.4 Change the default username

The default username will be removed once a new one is created.

Follow the command sequence below.

node~>enable

node~#configure

node~(cfg)#superuser <username> password <password>

3.5 Save the Configuration

Follow the command sequence below.

node~>enable

node~#configure

node~(cfg)#copy running-config startup-config

3.6 CopperLink LINE Commands

Local and Remote: This will set the Ethernet Extender as Local or Remote. Local is

typically used at the network, Remote is typically used at the remote device or remote

network. Your CopperLink CL2300 when received in a 2pk is already configured one

CL2300 as Local and one CL2300 as Remote.

node(cfg)# mode {local|remote}

Annex Type: Please consult support before changing this setting.

node~(pf-dsl)[<name>]# annex-type { b-g | a-f }

Line Rate Configuration: This will increase the line rate of the CL2300. Your Copper-

Link CL2300 is defaulted to automatically select the optimal rate based on the distance

(adaptive).

8CopperLink CL2300 Quick Start Guide

node(prt-line)[0/0]# payload-rate {adaptive [max

<192..15296>] | <192..15296>}

Modulation Scheme: Note higher TC-PAM rates will increase maximum payload rates

available but will decrease distance. Your CopperLink CL2300 is defaulted to automati-

cally select the optimal setting. Please consult manual for rate reach chart to determine

your optimal setting if you choose to hard set this value. Higher TC-PAM rates are ideal

for shorter cable runs offering max symmetrical (upstream/downstream) speeds of

11.4 Mbps (TCPAM64) and 15.3 Mbps (TCPAM128) per pair.

node(prt-line)[0/0]# tcpam {auto(16/32) | auto(64/128) |

16 | 32 | 64 | 128}

CopperLink Ports: The configurations below are used to configure various aspects of

the CopperLink port(s).

node~(cfg)# port dsl 0 0

Signal to Noise Ratio: Configures the acceptable noise margin for adaptive rate. SNR

is the relative strength of the DSL signal to Noise ratio. 6dB is generally the lowest dB

recommended in order for the modem to be able to synch. Generally speaking, as over-

all bandwidth increases, your signal to noise ratio decreases. The higher the number

the better. Your CL2300 is defaulted at 6 giving you the highest likelihood to connect.

node(prt-line)[0/0]# snr-margin <-10..22>

Description: This is the description of the port/line (CopperLink connection). (Ex:

"This line goes to building 4") When entering a description with spaces in the text , the

description must be in quotations.

node~(prt-dsl)[0/0]# description <description>

Use Profile: Configures the acceptable noise margin for adaptive rate. SNR is the rela-

tive strength of the DSL signal to Noise ratio. 6dB is generally the lowest dB recom-

mended in order for the modem to be able to synch.

node~(prt-dsl)[0/0]# use profile <name>

Service Mode: Configures the number of pairs (wires) you want to use. The CL2300

will default to the maximum number of wires available on your version of the Copper-

Link. CL2301 (2-wire); CL2302 (4-wire); CL2304 (8-wire).

node~(prt-dsl)[0/0]# service-mode { 2-wire | 4-wire | 6-

wire | 8-wire }

Shutdown: Disables or Enables CopperLink port(s).

node~(prt-dsl)[0/0]# [no] shutdown

Below 6dB bad

6dB-10dB fair

11dB-20dB good

CopperLink CL2300 Quick Start Guide 9

Exit: Goes back to parent mode.

node~(prt-dsl)[0/0]# exit

Show: Displays all the configured options of the CL2300 CopperLink port(s)

node(cfg)# show prt-line 0

4.0 Additional Information

For detailed information about configuring and operating guidance, set up procedures,

and troubleshooting, refer to the CopperLink CL2300 Series User Manual available

online at www.patton.com/manuals

5.0 Customer and Technical Support

Toll-Free VoIP support: call sip:[email protected] with a VoIP SIP phone

Online support: www.patton.com

E-mail support: [email protected]—answered within 1 business day

Telephone support:

6.0 Compliance

6.1 EMC

•FCC Part 15, Class A

•EN55022, Class A

•EN55024

6.2 Safety

•UL 60950-1/CSA C22.2 N0. 60950-1

•IEC/EN60950-1

•AS/NZS 60950-1

Standard USA +1 (301) 975-1007 Monday - Friday 8:00 am to 5:00 pm

EST (1300 to 2200 UTC/GMT)

Alternate Switzerland +41 (0)31-985-2555 Monday - Friday 8:00 am - 5:00 pm

CET (0900 to 1800 UTC/GMT)

Fax USA +1 (301) 869-9293

Switzerland +41 (0)31-985-2526

10 CopperLink CL2300 Quick Start Guide

6.3 PSTN Regulatory

•FCC Part 68

•CS-03

•AS/ACIF S043:2003

6.4 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by

ACTA. On the bottom side of this equipment is a label that contains—among other

information—a product identifier in the format US: AAAEQ##TXXXX. If requested, this

number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone net-

work must comply with the applicable FCC Part 68 rules and requirements adopted by

the ACTA.

If this equipment causes harm to the telephone network, the telephone company will

notify you in advance that temporary discontinuance of service may be required. But if

advance notice isn’t practical, the telephone company will notify the customer as soon

as possible. Also, you will be advised of your right to file a complaint with the FCC if

you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or

procedures that could affect the operation of the equipment. If this happens the tele-

phone company will provide advance notice in order for you to make necessary modifi-

cations to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please

contact our company. If the equipment is causing harm to the telephone network, the

telephone company may request that you disconnect the equipment until the problem

is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility

commission, public service commission or corporation commission for information.

6.5 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical

Specifications. This is confirmed by the registration number. The abbreviation, IC,

before the registration number signifies that registration was performed based on a

Declaration of Conformity indicating that Industry Canada technical specifications were

met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommuni-

cations network protective, operational and safety requirements. The Department does

not guarantee the equipment will operate to the user's satisfaction. Before installing

this equipment, users should ensure that it is permissible to be connected to the facili-

ties of the local telecommunications company. The equipment must also be installed

using an acceptable method of connection. In some cases, the company’s inside wiring

associated with a single line individual service may be extended by means of a certified

Andere Handbücher für CopperLink CL2300

Inhaltsverzeichnis

Andere Patton Extender Handbücher

Patton

Patton CopperLink CL1300MDE Bedienungsanleitung

Patton

Patton CopperLink E2168A Bedienungsanleitung

Patton

Patton 3231 Bedienungsanleitung

Patton

Patton CopperLink CL2300 Bedienungsanleitung

Patton

Patton CopperLINK 2174 Bedienungsanleitung

Patton

Patton 2168 Bedienungsanleitung

Patton

Patton CopperLink 1300R Bedienungsanleitung

Patton

Patton CopperLink CL1300 Bedienungsanleitung

Patton

Patton CopperLink 1314 Bedienungsanleitung

Patton

Patton 1053AS Bedienungsanleitung

Patton

Patton CopperLink 1101E/IP67 Bedienungsanleitung

Patton

Patton copperlink 1101 Bedienungsanleitung

Patton

Patton SmartNode 2290 Series Bedienungsanleitung

Patton

Patton CopperLink 2300 Bedienungsanleitung

Patton

Patton 2157R Bedienungsanleitung

Patton

Patton CopperLink 1214E Bedienungsanleitung

Patton

Patton SmartNode 2290 Series Bedienungsanleitung

Patton

Patton CopperLINK 2113A Bedienungsanleitung

Patton

Patton 2158 Bedienungsanleitung

Patton

Patton SmartNode 4830 Series Bedienungsanleitung

Patton

Patton CopperLink 1314MDE Bedienungsanleitung

Patton

Patton CopperLink 1214 Bedienungsanleitung

Patton

Patton 1052AS Bedienungsanleitung

Patton

Patton CopperLink 1314R Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung