Paxton Ins-20606 Bedienungsanleitung

Net2 Plus and Power supplies

ins-20606

Paxton

Mounting

1 2

Note: This mounting process applies to all types of cabinet and housing regardless of size, material or power supply included.

1. Screws and wall plugs are provided in a parts kit. With reference to the diagram, mark up the hole positions as required and drill the holes

suitable for No 8 wall plugs.

2. Tap in all three wall plugs and insert a long screw into the top, central mounting hole, leaving a suitable gap to the wall surface in order to slot

the cabinet over it.

3. Hang the cabinet over the inserted screw as directed and tighten until secure. If the cabinet is not suciently secure, be wary of the unit falling.

4. Secure the cabinet with the two lower screws.

This housing should be xed to the surface with suitable fasteners; screws and wall plugs are provided for this in the tting kit. Also provided are

cable ties to secure the cabling and a smaller securing screw for the lid.

318 mm

12.5“

7.8“

3.18 “

10.5 “

1 “

12.5”

200mm

159 mm

25 mm

81 mm

6.4 “

162 mm

3.9 “

6.2“

100 mm

268 mm

0.6 “15 mm

6.6 “

167 mm

200 mm

7.9”

200 mm

7.9”

200 mm

7.9”

2.71”

74 mm

2.9”

Metal cabinet Plastic cabinet

Net2 plus

PSU

ARM

SENSE

N.C.

N.O

COM

N.C.

N.O

COM

Data/D0

Clock/D1

CAT5

RS485

Media

Detect

TX RX

100

Data/D0

Clock/D1

Media

Detect

10/100 Ethernet

N.C.

N.O

COM

12V - 24V

12V

LED

12V

LED

EXIT

PSU

12V DC 12V DC

TX RX

Net2 plus

PSU

ARM

SENSE

N.C.

N.O

COM

N.C.

N.O

COM

Data/D0

Clock/D1

CAT5

RS485

Media

Detect

TX RX

100

Data/D0

Clock/D1

Media

Detect

10/100 Ethernet

N.C.

N.O

COM

12V - 24V

12V

LED

12V

LED

EXIT

PSU

12V DC 12V DC

TX RX

V21

V42

USP

N.C.

N.O

COM

N.C.

N.O

COM

Data/D0

Clock/D1

Data/D0

Clock/D1

12V

LED

12V DC

Paxton

N.C.

N.O

COM

N.C.

N.O

COM

Data/D0

Clock/D1

Data/D0

Clock/D1

12V

LED

12V DC

Paxton

N.C.

N.O

COM

N.C.

N.O

COM

Data/D0

Clock/D1

CAT5

RS485

TX RX

100

Data/D0

Clock/D1

10/100 Ethernet

N.C.

N.O

COM

12V - 24V

12V

LED

12V

LED

EXIT

12V DC 12V DC

Paxton Net2 plus

12V - 24V

10/100 Ethernet

RS485

CAT5

TX RX

Net2 plus

TX RX

RS485

CAT5

TX RX

12V

N.C.

COM

LED

EXIT

Wiring

Intruder alarm not evaluated by UL

The use of a Fail closed/Secure conguration shall be

determined by the local building codes and the local AHJ.

3 4

LED indications

Overview

• 12/24V (Green) Power LED.

• Relay 1 (Orange) The relay is energised - (NO/COM contacts are closed).

• Relay 2 (Orange) The relay is energised - (NO/COM contacts are closed).

• Alarm (Red) 12V Alarm output is active.

• Exit (Orange) The exit button contacts are closed.

• Contact (Orange) The door contacts are closed.

• Tamper (Orange) The tamper contacts are closed.

• PSU (Orange) The PSU contacts are closed.

• OK (Green ash) The internal software is running.

• Termination (Red) The on-board resistors are in place across the RS485 data pairs.

• Rx (Red) The ACU is receiving data (TCP/IP or RS485) - See also FAQ section.

• Tx (Green) The ACU is responding to data - (TCP/IP or RS485).

• Server Connected (Green) The TCP/IP interface is communicating with the PC Net2 server.

• Server Link - Green = 100 Mbit/s : Orange = 10 Mbit/s (TCP/IP speed).

A Net2 plus can connect to the Net2 PC using either an un-shielded RJ45 patch cable or an RS485 data line. This greatly increases the

number of installation options available to the installer.

Two typical site layouts are:

1 - The Net2 plus ACU’s can be individually connected to the Net2 PC via the site LAN network.

2 - Using a RS485 ‘daisy chain’dataline, a Net2 plus ACU can be used as a TCP/IP converter for a line of Net2 plus ACU’s.

When used with an RS485 data line, on-board termination resistors can be put in circuit with a simple slide switch. Ensure that units

installed in the middle of the data line have this switch turned OFF.

The Net2 plus shall be installed within the protected premises as both the power and lock wiring is present at the PCB. A Tamper alarm

input is provided on the PCB - See the Input/Output Wiring section

The Net2 plus’ will continue to operate in a ‘standalone’ mode if the PC is shut down or the dataline is disconnected. Any Events that

occur during this period are stored in the Net2 plus and the PC is updated when it comes back on line.

The PC must be running for any‘server based’ functions to operate. (Antipassback, Time and Attendance, etc)

To see the installation options available and important information relating to the installation and conguration of the Net2 plus, please

refer to the Application notes section on the website: paxton.info/1969

Input/Output wiring

Exit button

When the Exit terminal is shorted to 0V, the Exit LED will illuminate and the ACU will operate Relay 1. The reader/exit button Green LED will ash

during this period. More than one exit button can be wired in parallel. Relay 1 will remain transferred while the short to 0V remains.

Door Bell - Relay 2

Pressing the bell button on the keypad will result in Relay 2 being energized for 1 second. A bell sounder can be controlled by wiring one of the

bell feeds across COM / NO on the relay.

See Specication table for Output Ratings

Door contact

A NO switch may be tted so that it is held closed while the door is shut.

When connected, Net2 will check the door position during access activity and will raise an Alarm in the event of a‘Door Forced’or‘Door left open’

condition.

Tamper switch

The ACU supplied in a plastic housing has a ‘NO’ tamper switch tted and pre-wired into the circuit board.

The Tamper LED will be ON when the switch is closed. Net2 will monitor the switch position and will raise an Alarm in the event of a ‘Tamper’

condition.

Connect to a UL listed burglar alarm unit for supervision.

PSU monitoring

The Net 2 software will monitor the contacts and will raise an alarm in the event of a ‘Mains Fail’ condition.

The PSU Led will be on when the‘normally open’ contacts are‘closed’.

682-528-US

682-493-US

Input 12-24V DC 3A

Relay Output 24V DC 4A

Alarm Output 12V DC 1A

Reader Output 11.5V DC 500mA

CircuitModel Voltage Current

5 6

Alarm sounder

Lock Wiring - Relay output

Panic hardware/ Fire Door Interface

Intruder alarm integration

This local alarm has a transistor ‘open drain’output, (not a dry contact relay) and will switch 1A at 12V DC for a bell, light etc.

This local output can be turned on or o for each type of alarm and can be congured to sound continuously or intermittently to distinguish

between dierent alarm types.

Resistive loading only

This is a ONE door controller using a dry contact relay

The lock is wired across 12V and COM. A link (12V to NO or NC) is required, depending on lock type (Fail Closed / Open). Fit the supplied diode

across 12V and COM (Silver end to 12V ) to protect the relay contacts.

The dry relay contacts can be used to switch the power from an independent lock power supply. Wire the 12V to NC or NO and the lock to COM;

the 0V from the supply is wired directly to the lock

The ACU supplied in a plastic housing has a ‘NO’ tamper switch tted and pre-wired into the circuit board.

The Tamper LED will be ON when the switch is closed. Net2 will monitor the switch position and will raise an Alarm in the event of a ‘Tamper’

condition.

Connect to a UL listed burglar alarm unit for supervision.

A re alarm system must be used to release all re doors. External relay contacts are held closed by the re alarm’s interface and will be dropped

during an alarm condition. The system is fail safe as the door will release even if the cable burns through.

A dedicated port for input and output signals is provided when integrating a Net2 plus ACU with an alarm system.

Please see: AN1035 - Integrating Net2 with an intruder alarm system www.paxton.info/91 or call Technical Support for further information.

Arm - Arm conrmation Push Button - Wire across 0V and Arm.

Sense - Wire a voltage free loop across 0V and Sense to monitor the alarms current status.

Set - Wire a voltage free loop across COM and N.O. or N.C. to provide a set signal for the alarm

Note: Burglar alarm integration has not been evaluated by UL

Cable type

Wiring installation and test

Connecting to the PC or other ACU’s via the RS485 data connection

An RS485 data line has a 1000 yds maximum. This distance can be increased with the use of Paxton high speed repeaters or by using

shorter independent data lines using multiple LAN connections controlled from the same PC.

The RS485 communications port is used for uploading rmware and user information as well as providing Event information to the PC.

Category 5e cabling is the minimum performance category recommended

1. Wire the components to the Net2 Plus Access Control Unit (ACU) as shown on the third page.

2. Press the exit button or in the absence of an exit button short the 0V and exit terminals to test the relay function. The lock Relay LED

will come on and the lock should release.

3. If there are any Readers or keypads wired to the Net2 plus, ensure that all the LED’s are lit on each reader/keypad. Test each reader/

keypad by presenting a token to the unit. It should beep and display a single ashing red or green LED. The reader or keypads default

indication has all the LED’s on. Access granted is denoted with a single ashing Green LED. Access Denied is a single ashing Red LED.

The minimum conductor gauge permitted to connect between the PSE or power injector and the powered device shall be 26 AWG.

This product is for indoor use only and is not intended for outside wiring as covered by article 800 in the National Electrical code,

NFPA 70

Note: Each time the Net2 Plus is powered on, it will run an internal health check. During this phase (about 5 secs) the OK LED will ash

quickly before changing to a slower heartbeat.

90% of installation faults are caused by wiring errors on the RS485 data line.

Special attention to this area can save time and eort.

RS485 data line 1000 yrds 2 x twisted pairs - Belden 8723 or Cat5 equivalent

Input/Output 100 yrds 2 conductor - Alpha 1172C (22AWG) or equivalent

Reader/Keypad 82 feet 8 core, shielded - Belden 9538/ 5506FE (22/24AWG/ 8C)

or General Cable C0744A/ E2008S (22/24AWG/8C)

Reader/Keypad 328 feet 8 core shielded cable - Belden 9540/ 5306FE (24/18 AWG/10C/8C)

or General Cable C0745A/ General Cable C0745A (24/18 AWG/10C/8C)

TypeMax lengthUse

7 8

TCP/IP and RS485 LED indication

Maintenance

RS485 data line resistance check

The Net2 plus performs two functions. It is an access control unit and also a TCP/IP RS485 converter. Information can pass across the

PCB between the TCP/IP and RS485 data port but is not relevant to this ACU.

• Server Connected LED (Steady Green)

This LED shows that the TCP/IP interface is active and receiving data from the Net2 PC server. This includes all data for other ACU’s that

may be linked via the RS485 data port.

• Rx and Tx LED’s

These LED’s show the activity for this ACU only. It is not dependant on the source (TCP/IP or RS485). The Rx LED will ash for all data

being received and the Tx LED will only ash when this unit responds to its own address.

It is advisable to ensure that any third party backup power supplies or recovery procedures are checked regularly to ensure that the

operation of the Paxton system is not compromised.

1 - Short circuiting, mutilation or incineration of the cells must be avoided to prevent one or more of the following occurrences; Release

of toxic materials, release of hydrogen and/or oxygen gas, rise in surface temperature.

2 - If a cell has leaked or vented the control unit must be replaced. The battery is not to be replaced

End of line termination - 120 ohm resistors must be linked across each data pair at the beginning AND end of the line. This can be done

on many units with a switch or jumpers. If not, resistors are provided with the converter.

Reader & Data Cable Screens

• Data cable screens and spare cores MUST be connected throughout.

• Reader and keypad screens where provided, should be connected to the Black 0V terminal.

The data line must be wired in a single daisy chain. The data connection to the PC may be located at any position along the data line.

Power down all TCP/IP, USB and RS232 converters (individual and Net2 plus).

1. Check the resistance across each data pair is 60-80 ohms.

2. Check that there are no data line to screen shorts.

3. Check the screen of the data cable is continuous - this provides the 0V DC system reference

802.3at

+12V DC

Clock/D1

COM

12V

LED

EXIT

12V DC

Paxton

Net2 plus

N.C.

12V DC PoE+ power supply in cabinet with Net2 plus

+12V DC Outputs

Combined data and

power from a PSE (Power

source equipment)

This LED is on when the

input supply is healthy

This LED is on when the

unit is operating in high

power mode

Ethernet data

Inhaltsverzeichnis

Andere Paxton Steuerungssystem Handbücher

Paxton

Paxton Net2Air Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung

EMKO

EMKO TRANS-SYNCRO Bedienungsanleitung

Dover

Dover TWG GC ELEMENT II Programmierhandbuch

Paxton ins-20606 Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken