Paxton Ins-40213-US Bedienungsanleitung

Paxton

ins-40213-US

Paxlock US

x 2 x 2

X 3

910

17 18

19*

20 21

Tools List

What’s in the box

1) Front handle

2) Lock Cylinder *

3) Paxlock front housing

4) Motor adjustment plate

5) Motor

6) 2-3/8” Latch

7) Latch screws x 2

8) Motor backplate

9) Backplate/Rose assembly

10) Paxlock rear housing

11) 4 x AA Alkaline batteries

12) Rear battery cover

13) Rear handle cover

14) Rear Handle

15) Small mounting screws x 2

16) Long mounting screws x 3

17) Battery cover key

18) Handle removal pin

19) Keys x 2 *

20) Handle washers x 2

21) Strike plate

22) Strike plate screws x 2

Knife

Adhesive tape

Pencil

Tape measure

* Not for SFIC

Power Drill

Drill bits (1”, 5/16”, 5/8”, 1/8”)

Crosshead screwdriver

Chisel 1”

2-3/8” (60mm) backset

5/16” (8mm)

5/16” (8mm) 5/16” (8mm)

2-1/8” (54mm)

5/16” (8mm)

5/8” (16mm)

1” (25mm) Width

3-1/4” (82mm) Depth

x 2 x 2

X 3

910

17 18

19*

20 21

Step 1: Marking out

Tape template to door, mark holes then remove

template for drilling.

Step 2: Drilling

To ensure accuracy you should drill holes from

both sides of the door towards the center. This

avoids the risk of damaging the door face when

the drill breaks through.

Make sure to include pilot holes either side of

the central hole to ensure ush tting of the

motor plates.

Step 3: Marking out and chiseling for latch

To install the latch; drill a 1”(25mm) hole, slide in

the latch, then draw around the faceplate.

Remove the latch and score the outline with

a knife to avoid splitting the wood when

chiselling.

Step 6: Inserting the motor

Pass the motor through the central hole within

the door, making sure to pass the motor lead

through the hole rst.

Step 5: Fitting the strike plate

Close the door to mark the horizontal line of the

strike plate.

Measure one half of door thickness from door

stop to mark vertical center line of the strike.

Drill 1” (25.4mm) hole, 1/2” (12.7mm) deep at

intersection of horizontal and vertical center

lines.

Cut out jamb 3/32” (2.4mm) deep or until the

strike is ush with jamb. Tighten the strike plate

screws securely.

Step 4: Fitting the door latch

Attach the latch using the screws provided.

- 1-3/4” (45mm)

- 2” (50mm)

Step 8: Ensuring the latch engages

Make sure the tail of the latch is engaging with

the motor retractor correctly as illustrated.

Step 7: Rotating the motor adjustment plate

To ensure that the motor adjustment plate is at

the correct distance, rotate until it sits ush with

the door and the motor has engaged properly.

Please refer to the diagram for the correct

position of the plate for each door thickness.

Step 9: Fitting the front housing

Line up front housing and ensure the body is

ush to the door.

*PaxLock US is set up for RH doors by default –

please see page 8 for LH operation.

Step 10: Fitting the rear backplate

assembly

Feed the motor cable through the

hole in the motor back plate.

Step 11: Fitting the rear housing and motor

wiring

Feed both the cables through the rear housing

cutout and t the lower long mounting screws.

Step 12: Fitting the rear lock assembly and

wiring

Fit top, long mounting screws and 2 lower short

screws.

Step 10: Fitting the batteries

Step 11: Securing the rear cover

Step 12: Fitting the cover plate and handle

Optional step: Contact switch Optional step: Inserting the handle washers

Handle feel can be tightened with the use of

the included washers.

Optional step: Handle orientation for LH door

To congure for LH door operation, remove the front and rear handles using the handle removal

pin. Unscrew the 4 screws securing the rose to the front/rear housings, rotate 180 degrees and

screw back together.

Ret the handles, and push home until the axle engagement clicks.

≤ 200

≤ 1000

Net2 Pro/Net2 Lite: http://paxton.info/1438

Software installation

0 m

15m

20m

30m

50ft

65ft

100ft

10ft

0 ft

Wireless Signal Range

Enrolling a PaxLock

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Paxton IP-Zugriffskontrollsysteme Handbücher

Paxton

Paxton Ins-30150-US Bedienungsanleitung

Paxton

Paxton TOUCHLOCK APN-1003 Fehlerbehebungshandbuch

Paxton

Paxton PROXIMITY P series Bedienungsanleitung

Paxton

Paxton Easyprox nano Bedienungsanleitung

Paxton

Paxton Net2 PaxLock Bedienungsanleitung

Paxton

Paxton 353467V2 Bedienungsanleitung

Paxton

Paxton TOUCHLOCK K Series Bedienungsanleitung

Paxton

Paxton PROXIMITY P38 Bedienungsanleitung

Paxton

Paxton ins-30093-EX Bedienungsanleitung

Paxton

Paxton ins-20100 Bedienungsanleitung

Paxton

Paxton Ins-30160 Bedienungsanleitung

Paxton

Paxton Ins-30003 PROXIMITY P Series Bedienungsanleitung

Paxton

Paxton 333-110 Bedienungsanleitung

Paxton

Paxton Ins-30130 Bedienungsanleitung

Paxton

Paxton Proximity LCD reader Bedienungsanleitung

Paxton

Paxton Ins-30156 PROXIMITY P Series Bedienungsanleitung

Paxton

Paxton Switch2 Bedienungsanleitung

Paxton

Paxton 690-333-US Bedienungsanleitung

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken

ZKTeco

ZKTeco SpeedFace-V5L Bedienungsanleitung

2N Access Unit Merkblatt

Kedacom

Kedacom KSCA120 Series Bedienungsanleitung

H3C

H3C WX2880X Bedienungsanleitung

G4S

G4S S870-EX Leitfaden

PRASTEL

PRASTEL M2000PE Bedienungsanleitung

Allegion

Allegion interflex IF-281 Cylinder Bedienungsanleitung

TECOM

TECOM TS1067E Bedienungsanleitung

Fermax

Fermax Memokey 100C Benutzerhandbuch

Fermax

Fermax CITYLINE MEMOKEY Bedienungsanleitung

AKCP

AKCP SP+ Bedienungsanleitung

Bpt

Bpt HNA/102 Bedienungsanleitung

Civintec

Civintec CV9601T-T-1F Bedienungsanleitung

BioMax

BioMax N-X90W Bedienungsanleitung

ZKTeco

ZKTeco OP-200 Bedienungsanleitung

FingerTec

FingerTec s-Kadex Bedienungsanleitung

H3C

H3C WX5002ACCESSCONTROLLER Bedienungsanleitung

C Prox Ltd

C Prox Ltd DPN-2 Bedienungsanleitung

Paxton ins-40213-US Bedienungsanleitung

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken