PCchips A32G Bedienungsanleitung

Motherboard User’s Guide

This publication, including photographs, illustrations and software, is under

therthismanual,noranyofthematerialcontainedherein,maybereproduced

without the express written consent of the manufacturer.

The information in this document is subject to change without notice. The

manufacturer makes no representations or warranties with respect to the

contents hereof and specifically disclaims any implied warranties of mer-

chantability or fitness for any particular purpose. Further, the manufacturer

reserves the right to revise this publication and to make changes from time to

time in the content hereof without obligation of the manufacturer to notify

any person of such revision or changes.

Trademarks

IBM, VGA, and PS/2 are registered trademarks of International Business

Machines.

AMD, Athlon 64 Sempron are registered trademarks of Advanced Micro

Devices Inc.

Microsoft, MS-DOS and Windows 98SE/ME/NT/2000/XP are registered

trademarks of Microsoft Corporation.

AMI is a registered trademark ofAmerican Megatrends Inc.

Other names used in this publication may be trademarks and are acknowl-

edged.

Static Electricity Precautions

1. Don’t take this motherboard and components out of their original

static-proof package until you are ready to install them.

2. While installing, please wear a grounded wrist strap if possible. If

you don’t have a wrist strap, discharge static electricity by touching

the bare metal of the system chassis.

3. Carefully hold this motherboard by its edges. Do not touch those

components unless it is absolutely necessary. Put this motherboard

on the top of static-protection package with component side facing

up while installing.

Pre-Installation Inspection

1. Inspect this motherboard whether there are any damages to compo-

nents and connectors on the board.

2. If you suspect this motherboard has been damaged, do not connect

power to the system. Contact your mainboard vendor about those

damages.

Motherboard User’s Guide

Table of Contents

Trademark.....................................................................................................................i

Chapter 1: Introduction............................................................................1

Key Features..............................................................................................1

Package Contents......................................................................................4

Chapter 2: Motherboard Installation......................................................5

Motherboard Components.........................................................................6

I/O Ports....................................................................................................7

Installing Memory Modules.......................................................................8

Jumper Settings.......................................................................................10

Install the Motherboard...........................................................................10

Connecting Optional Devices...................................................................12

Install Other Devices................................................................................15

Expansion Slots ......................................................................................17

Chapter 3: BIOS Setup Utility..............................................................19

Introduction............................................................................................19

Running the Setup Utility.........................................................................19

Standard CMOS Setup Page....................................................................20

Advanced Setup Page..............................................................................21

Features Setup Page................................................................................22

Power Management Setup Page..............................................................24

PCI/Plug and Play Setup Page................................................................25

BIOS Security Features Setup Page.........................................................26

CPU PnP Setup Page..............................................................................26

Hardware Monitor Page..........................................................................27

Load Optimal Defaults............................................................................28

Save Changes and Exit............................................................................28

Discard Changes and Exit.......................................................................28

Chapter 4: Software & Applications.....................................................29

Introduction............................................................................................29

Installing Support Software.....................................................................29

Bundled Software Installation..................................................................31

iii

Motherboard User’s Guide

Notice:

1. Owing to Microsoft’s certifying schedule is various to every supplier,

we might have some drivers not certified yet by Microsoft. There-

fore, it might happen under Windows XP that a dialogue box (shown

as below) pops out warning you this software has not passed Win-

dows Logo testing to verify its compatibility with Windows XP.

Please rest assured that our RD department has already tested and

verified these drivers. Just click the “ContinueAnyway” button and

go ahead the installation.

2. USB 2.0 Driver Limitations:

2-1. The USB 2.0 driver only supports Windows XP and Windows

2000.

2-2. If you connect a USB 2.0 hub to the root hub, plugging USB devices

into this hub, the system might not successfully execute certain USB

devices’ connection because it could not recognize these devices.

Motherboard User’s Guide

Chapter 1 Introduction

This motherboard has onboard AMD Sempron™/Athlon™processors with

Front Side Bus (FSB) 800 MHz and HyperTransport Technology.

It integrates the SiS761GX Northbridge and SiS965L Southbridge that sup-

ports the built-in USB 2.0 providing higher bandwidth, implementing Uni-

versal Serial Bus Specification Revision 2.0 and is compliant with UHCI 1.1

and EHCI 0.95. It supports AC’ 97 Audio Codec and provides Ultra DMA

133/100/66 function. It has one PCI Express x16, one CNR and two 32-bit

PCI slots. There is a full set of I/O ports including two PS/2 ports for mouse

and keyboard, one serial port, one parallel port, one LAN port (optional),

one VGA port, three audio jacks for Line-in, Line-out and Microphone, four

back-panel USB2.0 ports and onboard USB headers providing extra ports

by connecting the Extended USB Module to the motherboard.

This motherboard is a MicroATX size motherboard and has power connec-

tors for an ATX power supply.

Key Features

The key features of this motherboard include:

AMD Sempron™/Athlon™Processors Support

•Supports AMD Sempron™/Athlon™processors

•Supports Front-Side Bus 800 MHz

Note: HyperTransport Technology is a point-to-point link between two

devices, it enables integrated circuits to exchange information at

much higher speeds than currently available interconnect

technologies.

Chipset

ThereareSiS761GXNorthbridgeandSiS965LSouthbridge in this chipset in

accordance with an innovative and scalable architecture with proven reliabil-

ity and performance.

•High Performance Host Interface:

−HyperTransport compliant bus driver with auto compensation

capability

•Integrated Host-to-PCI Express Bridge:

−1 Gb/s performance in 133 MHz x 4 mode

−Distributed arbitration strategy with enhanced mode of contigu-

ous

DMA data streaming

•High Performance & High Quality 3D GraphicsAccelerator:

−Built-in 32-bit floating point format VLIM triangle setup engine

−Built-in 2 pixel rendering pipelines and 4 texture units

Motherboard User’s Guide

Memory Support

•Two 184-pin DIMM sockets for DDR SDRAM memory modules

•Supports DDR 333/266 memory bus

•Maximum installed memory is 2 GB

Expansion Slots

•One PCI Express x16 slot

•Two 32-bit PCI slots for PCI 2.3-compliant bus interface

•One CNR slot

Onboard IDE channels

•Two IDE Connectors

•Supports PIO (Programmable Input/Output) and DMA (Direct

Memory Access) modes

•Supports IDE Ultra DMA bus mastering with transfer rates of

133/100/66 MB/sec

SerialATA

•Two Serial ATA Connectors

•Transfer rate exceeding best ATA (~150 MB/s) with scalability to

higher rates

•Low pin count for both host and devices

AC’97 Codec

•AC ’97 2.3 COMPATIBLE

•FEATURES6 DAC Channels for 5.1 Surround

•90 dB Dynamic Range

•20-Bit PCM DACs

•S/PDIF Output Integrated Stereo Headphone Amplifiers

•Line-In

•High Quality CD Input

•Selectable MIC Input

•Mono Output

•ExternalAmplifier Power-Down Control

Onboard I/O Ports

•Two PS/2 ports for mouse and keyboard

•One serial port

•One parallel port

•PCI 2.3 Specification Compliance

•Integrated Multithreaded I/O Link Mastering

•Multithread I/O Link Mastering with Read/Write Concurrent and

Read/Read Pipeline Transaction

Chapter 1: Introduction

USB 2.0

•Compliant with Universal Serial Bus Specification Revision 2.0

•Compliant with Intel’s Enhanced Host Controller Interface

Specification Revision 1.0

•Compliant with Universal Host Controller Interface Specification

Revision 1.1

•PCI multi-function device consists of two UHCI Host Controller

cores for full-/low-speed signaling and one EHCI Host Controller

corefor high-speed signaling

•Root hub consists 4 downstream facing ports with integrated

physical layer transceivers shared by UHCI and EHCI Host

Controller, up to eight functional ports

•Support PCI-Bus Power Management Interface Specification

release 1.1

•Legacy support for all downstream facing ports

BIOS Firmware

This motherboard uses AMI BIOS that enables users to configure many

system features including the following:

•Powermanagement

•Wake-up alarms

•CPU parameters and memory timing

•CPU and memory timing

The firmware can also be used to set parameters for different processor clock

speeds.

Dimensions

•Micro ATX form factor of 244 x 200 mm

Note: Hardware specifications and software items are subject to change

without notification.

•One VGA port

•Four back-panel USB2.0 ports

•One LAN port (optional)

•Audio jacks for microphone, line-in and line-out

Fast Ethernet LAN (optional)

•Supports 10/100 Mbps operation and half/full duplex operation

•IEEE 802.3/802.3u compliant

•Supports IEEE 802.3u clause 28 auto negotiation

•Supports operation under Link Down Power Saving mode

•Supports Base Line Winder (BLW) compensation

•Adaptive Equalization

Motherboard User’s Guide

Package Contents

Your motherboard package ships with the following items:

The motherboard

The User’s Guide

One diskette drive ribbon cable (optional)

One IDE drive ribbon cable

The Software support CD

Optional Accessories

You can purchase the following optional accessories for this motherboard.

The Extended USB module

The CNR v.90 56K Fax/Modem card

The SerialATAcable

The SerialATApower cable

Note: You can purchase your own optional accessories from the third

party, but please contact your local vendor on any issues of the

specification and compatibility.

Chapter 2: Motherboard Installation

Chapter 2 Motherboard Installation

To install this motherboard in a system, please follow these instructions in

this chapter:

Identify the motherboard components

Install one or more system memory modules

Make sure all jumpers and switches are set correctly

Install this motherboard in a system chassis (case)

Connect any extension brackets or cables to headers/connectors on

the motherboard

Install peripheral devices and make the appropriate connections to

headers/connectors on the motherboard

Note:

1 Before installing this motherboard, make sure jumper

CLR_CMOS1 is under Normal setting. See this chapter for

information about locating CLR_CMOS1 and the setting options.

2 Never connect power to the system during installation; otherwise,

it may damage the motherboard.

Motherboard User’s Guide

Motherboard Components

ITEM LABEL COMPONENTS

1 DDR1/2 184-pin DDRSDRAMsockets

2IR1 Infrared header

3PWR1 Standard 24-Pin ATX Power connector

4FDD1 Floppy Disk Drive connector

5IDE1 Primary IDE connector

6IDE2 Secondary IDE connector

7SATA1/2 Serial ATA connectors

8PANEL1 Front Panel Switch/LED header

9SYS_FAN1 System Fan connector

10 SPK1 Speaker header

11 CLR_CMOS1 Clear CMOS jumper

12 F_USB1/2 Front Panel USB headers

13 CNR1 CNR slot

14 PCI 1-2 32-bit PCI slots

15 CD_IN1 AnalogAudio Input header

16 SPDIFO1 SPDIF Out header

17 PCI-E1 PCI-Express x16 slot

18 F_AUDIO1 Front Panel Audio header

19 CPU_FAN1 CPU Fan connector(3PIN)

20 PWR2 Standard 4-Pin ATX Power connector

Chapter 2: Motherboard Installation

PS/2 Mouse Use the upper PS/2 port to connect a PS/2 pointing

device.

PS/2 Keyboard Use the lower PS/2 port to connect a PS/2

keyboard.

Parallel Port (LPT1) Use the Parallel port to connect printers or other

parallel communications devices.

SerialPort (COM1) Use the COMport to connect serial devices such

as mice or fax/modems. COM1 is identified by the

systemas COM1.

VGA Port Use the VGA port to connect VGA devices.

LANPort (optional) Connect an RJ-45 jack to the LAN port to connect

your computer to the Network.

USB Ports Use the USB ports to connect USB devices.

Audio Ports Use these three audio jacks to connect audio

devices. The first jack is for stereo Line-In signal,

the second jack for stereo Line-Out signal, and the

third jack for Microphone.

I/O Ports

The illustration below shows a side view of the built-in I/O ports on the

motherboard.

Inhaltsverzeichnis

Andere PCchips Hauptplatine Handbücher

PCchips

PCchips M851AG Bedienungsanleitung

PCchips

PCchips M905ULR 3.2 Bedienungsanleitung

PCchips

PCchips M717 Bedienungsanleitung

PCchips

PCchips M925 Series Bedienungsanleitung

PCchips

PCchips P51G Series Bedienungsanleitung

PCchips

PCchips M755LMR Bedienungsanleitung

PCchips

PCchips M925G Series Bedienungsanleitung

PCchips

PCchips M758LMT Bedienungsanleitung

PCchips

PCchips M863G Bedienungsanleitung

PCchips

PCchips M758LMR Bedienungsanleitung

PCchips

PCchips M825G Series Bedienungsanleitung

PCchips

PCchips M939LU Bedienungsanleitung

PCchips

PCchips M935 Series Bedienungsanleitung

PCchips

PCchips A41G V7.0 Bedienungsanleitung

PCchips

PCchips M935ALU Bedienungsanleitung

PCchips

PCchips M922ULR Bedienungsanleitung

PCchips

PCchips M765MRT Bedienungsanleitung

PCchips

PCchips M810LMR Bedienungsanleitung

PCchips

PCchips M765VMRT Bedienungsanleitung

PCchips

PCchips P47G Series Bedienungsanleitung

PCchips

PCchips M852 Bedienungsanleitung

PCchips

PCchips M957G Bedienungsanleitung

PCchips

PCchips Motherboard Bedienungsanleitung

PCchips

PCchips M575V12 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung