PCchips M902LU V3.0 Bedienungsanleitung

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without writtenconsent ofthe au-

thor.

Version 3.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

−Reorient or relocate the receiving antenna.

−Increase the separation between the equipment and the receiver.

−Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

−Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

−This device may not cause harmful interference, and

−This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 5

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 24

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 36

iii

Preface i

Features and Packing List Translations 錯誤! 尚未定義書籤。

CHAPTER 1 1

Introducing the Mainboard 1

Introduction............................................................................................................1

Checklist.................................................................................................................1

Standard Items...................................................................................................1

Features..................................................................................................................2

Choosing a Computer Case................................................................................3

Mainboard Components.......................................................................................4

CHAPTER 2 5

Installing the Mainboard 5

Safety Precautions................................................................................................5

Quick Guide...........................................................................................................5

Installing the Mainboard in a Case.....................................................................6

Checking Jumper Settings...................................................................................6

Setting Jumpers.................................................................................................6

Checking Jumper Settings .................................................................................7

Jumper Settings .................................................................................................7

Connecting Case Components...........................................................................9

The PANEL1 Connector..................................................................................10

Installing Hardware.............................................................................................11

Installing the Processor ...................................................................................11

Installing Memory Modules............................................................................14

Installing a Hard Disk Drive/CD-ROM..........................................................15

Installing a Floppy Diskette Drive..................................................................17

InstallingAdd-on Cards...................................................................................18

Connecting Optional Devices..........................................................................20

ConnectingI/ODevices.....................................................................................22

CHAPTER 3 24

Using BIOS 24

About the Setup Utility........................................................................................24

The Standard Configuration............................................................................24

Running the Setup Utility................................................................................25

Using BIOS..........................................................................................................25

Standard CMOS Setup Page............................................................................26

Advanced Setup Page......................................................................................27

Power Management Setup Page ...................................................................... 29

PCI / Plug and Play Setup...............................................................................30

Load Optimal Settings.....................................................................................31

Load Best Performance Settings .....................................................................31

Features Setup Page.........................................................................................31

CPU PnP SetupPage .......................................................................................33

Hardware Monitor Page ..................................................................................34

Change Password............................................................................................35

Change or Remove the Password....................................................................35

Exit ..................................................................................................................35

CHAPTER 4 36

Using the Mainboard Software 36

About the Software CD-ROM............................................................................36

Auto-installing under Windows 98/ME/2000/XP............................................36

Running Setup.................................................................................................37

Manual Installation..............................................................................................39

Utility Software Reference.................................................................................39

Introducing the Mainboard

Thank you for choosing the P4IBASD mainboard. This mainboard has a

Socket-478 support for Intel Pentium4 processors with front-side bus (FSB)

speeds up to 400/533 MHz.

This mainboard has the Intel 845D chipset that contains Intel 82845 Memory

Controller Hub and Intel 82801BA I/O Controller Hub. It supports AC 97 audio

codec and provides Ultra DMA 33/66/100 function. This mainboard has five

32-bit PCI, one 4xAGP and one CNR (Communications and Networking Riser)

slot. There is a full set of I/O ports including two PS/2 ports for mouse and

keyboard, two serial ports, one parallel port, one MIDI/game port and maxi-

mum six USB ports. By means of the Extended USB Module connected to the

mainboard, you can make maximum four extra USB ports.

This mainboard is an ATX mainboard that uses a 4-layer printed circuit board

and measures 305 x 244mm.

Compare the mainboard’s package contents with the following checklist:

Standard Items

•One mainboard

•One diskette drive ribbon cable

•One IDE drive ribbon cable

•Software support CD

•One Retention module

•The User’s Manual

Processor •Supports mPGA Socket 478

•Supports Intel Pentium 4 series CPUs

•Supports up to 400/533 MHz system Bus

Memory •Two 168-pin DIMM slots for SDRAM memory modules

•Two 184-pin DIMM slots for DDR SDRAM memory mod-

ules

•Support SDRAM up to 133 MHz/DDR up to 266 MHz

memory bus

•Maximum installed memory is 2GB

Note: You cannot use SDRAM and DDR concurrently.

Expansion Slots

•Four 32-bit PCI Master slots (PCI 2~5) and one Slave slot

(PCI 1)

•Supports IDE Ultra DMA bus mastering with transfer rates

of 33/66/100 MB/sec

•One 4xAGP slot -supports 1.5V 4x AGP card only

•One CNR (Communications and Networking Riser) slot

AC’97 Audio

Codec The AC 97 Audio codec is compliant with the AC 97 2.2 speci-

fication, and supports 18-bit ADC (Analog Digital Converter)

and DAC (Digital Analog Converter) resolution as well as 18-bit

stereo full-duplex codec with independent and variable sam-

pling rates. Further features include support for four analog

line-level stereo inputs.

Built-in Ethernet

LAN (optional) •Built-in 10BaseT/100BaseTX Ethernet LAN

•Integrated Fast Ethernet MAC and full compliance with

IEEE 802.3u 100 Base-T specifications and IEEE 802.3x

Full Duplex Flow Control

•In compliance with ACPI 1.0 and the Network Device

Class Power Management 1.0

•High Performance achieved by 100Mbps clock generator

and data recovery circuit for 100Mbps receiver

Onboard I/O

Ports •Two PS/2 ports for mouse and keyboard

•Two serial ports

•One parallel port

•One MIDI/game port

•Six USB ports (two back-panel USB 2.0 ports, onboard

USB headers providing maximum four extra ports: header

JUSB2 for USB 2.0 and header USB2 for USB 1.1)

•Audio jacks for microphone, line-in and line-out

USB 2.0

(optional

VT6202)

•

Compliant with Universal Serial Bus Specification Rev

sion 2.0

•Compliant with Intel’s Enhanced Host Controller

Interface Specification Revision 0.95

•Compliant with Universal Host Controller Interface

Specification Revision 1.1

•PCI multi-function device consists of two UHCI Host

Controller cores for full-/low-speed signaling and one

EHCI Host Controller core for high-speed signaling

•Root hub consists 4 downstream facing ports with

integrated physical layer transceivers shared by UHCI

and EHCI Host Controller

•Support PCI-Bus Power Management Interface

Specification release 1.1

•Legacy support for all downstream facing ports

BIOS Firmware This mainboard uses AMI BIOS that enables users to config-

ure many system features including the following:

•Power management

•Wake-up alarms

•CPU parameters and memory timing

•CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

Dimensions ATX form factor of305 x 244mm

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the ATX system case. Some features on the

mainboard are implemented by cabling connectors on the mainboard to indi-

cators and switches on the system case. Ensure that your case supports all

the features required. The mainboard can support one floppy diskette drive

and four enhanced IDE drives. Ensure that your case has sufficient power and

space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has an ATX form factor of 305 x 244 mm. Choose a case that

accommodates this form factor.

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Installing the Mainboard

Follow these safety precautions when installing the mainboard:

•Wear a grounding strap attached to a grounded device to avoid

damage from static electricity.

•Discharge static electricity by touching the metal case of a safely

grounded object before working on the mainboard.

•Leave components in the static-proof bags they came in.

•Hold all circuit boards by the edges. Do not bend circuit boards.

This Quick Guide suggests the steps you can take to assemble your system

with the mainboards.

The following table provides a reference for installing specific components:

Locating Mainboard Components Go to page 4

Installing the Mainboard in a Case Go to page 6

Setting Jumpers Go to page 6

Installing Case Components Go to page 9

Installing the CPU Go to page 11

Installing Memory Go to page 14

Installing an HDD and CD-ROM Drive Go to page 15

Installing an FDD Go to page 17

Installing Add-on Cards Go to page 18

Connecting Options Go to page 20

Connecting Peripheral (I/O) Devices Go to page 22

Refer to the following illustration and instructions for installing the mainboard

in a case:

This illustration shows an ex-

ample of a mainboard being

installed in a tower-type case:

Note: Do not overtighten

the screws as this

can stress the main-

board.

Most system cases have

mounting brackets installed in

the case, which correspond to

the holes in the mainboard.

Place the mainboard over the

mounting brackets and secure

the mainboard onto the mount-

ing brackets with screws.

2. Secure the mainboard with

screwswhereappropriate.

1. Place the mainboard

over the mounting brackets.

Ensure that your case has an I/O template that supports the I/O ports and

expansion slots on your mainboard.

This section explains how to set jumpers for correct configuration of the main-

board.

Setting Jumpers

Use the mainboard jumpers to set system configuration options. Jumpers with

more than one pin are numbered. When setting the jumpers, ensure that the

jumper caps are placed on the correct pins.

The illustrations below show a 2-pin jumper.

When the jumper cap is placed on both pins,

the jumper is SHORT. If you remove the

jumper cap, or place the jumper cap on just

one pin, the jumper is OPEN.

This illustration shows a 3-pin

jumper. Pins 1 and 2 are SHORT.

Short Open

Inhaltsverzeichnis

Andere PCchips Hauptplatine Handbücher

PCchips

PCchips M596 Bedienungsanleitung

PCchips

PCchips K7S5A Bedienungsanleitung

PCchips

PCchips Motherboard Bedienungsanleitung

PCchips

PCchips M810LMR 3.0x Bedienungsanleitung

PCchips

PCchips M930LR Bedienungsanleitung

PCchips

PCchips M852 Bedienungsanleitung

PCchips

PCchips M925G 8.0 Bedienungsanleitung

PCchips

PCchips M957G Bedienungsanleitung

PCchips

PCchips M787CLR Bedienungsanleitung

PCchips

PCchips M717 Bedienungsanleitung

PCchips

PCchips A21G Bedienungsanleitung

PCchips

PCchips M586MR Bedienungsanleitung

PCchips

PCchips Tidalwave W30 Bedienungsanleitung

PCchips

PCchips P53G Series Bedienungsanleitung

PCchips

PCchips M848LU Bedienungsanleitung

PCchips

PCchips M939LU Bedienungsanleitung

PCchips

PCchips M922ULR Bedienungsanleitung

PCchips

PCchips M748LMRT Bedienungsanleitung

PCchips

PCchips M935D Bedienungsanleitung

PCchips

PCchips M757MR Bedienungsanleitung

PCchips

PCchips A41G V7.0 Bedienungsanleitung

PCchips

PCchips M786 Series Bedienungsanleitung

PCchips

PCchips M935 Series Bedienungsanleitung

PCchips

PCchips M575V12 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung