PCchips M922LR V1.1 Bedienungsanleitung

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without written consent of the au-

thor.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

− Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and the receiver.

− Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

− Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

KOB P4X266 NDFSX, V1.0

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

− This device may not cause harmful interference, and

− This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard

Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard

Describes installation of mainboard

components.

Go to ⇒page 5

Chapter 3

Using BIOS

Provides information on using the BIOS

Setup Utility.

Go to ⇒page 21

Chapter 4

Using the Mainboard Software

Describes the mainboard software.

Go to ⇒page 34

Preface i

CHAPTER 1 1

Introducing the Mainboard 1

Introduction.................................................................................................1

Checklist .....................................................................................................1

Standard Items ................................................................................................. 1

Features .....................................................................................................2

Choosing a Computer Case .......................................................................3

Mainboard Components .............................................................................4

CHAPTER 2 5

Installing the Mainboard 5

Safety Precautions......................................................................................5

Quick Guide................................................................................................5

Installing the Mainboard in a Case..............................................................6

Checking Jumper Settings..........................................................................6

Setting Jumpers ............................................................................................... 6

Checking Jumper Settings ............................................................................... 7

Jumper Settings ............................................................................................... 7

Connecting Case Components...................................................................9

The Panel Connectors.................................................................................... 10

Installing Hardware ...................................................................................10

Installing the Processor.................................................................................. 10

Installing Memory Modules .......................................................................... 13

Installing a Hard Disk Drive/CD-ROM......................................................... 14

Installing a Floppy Diskette Drive................................................................. 15

Installing Add-on Cards................................................................................. 16

Connecting Optional Devices........................................................................ 17

Connecting I/O Devices ............................................................................19

External Connector Color Coding ................................................................. 20

CHAPTER 3 21

Using BIOS 21

About the Setup Utility ..............................................................................21

The Standard Configuration .......................................................................... 21

Entering the Setup Utility .............................................................................. 22

Updating the BIOS ........................................................................................ 22

Using BIOS...............................................................................................23

Standard CMOS Features .............................................................................. 24

Advanced Setup Page .................................................................................... 25

iii

Power Management Setup Page .................................................................... 27

PCI/Plug and Play Setup Page....................................................................... 29

Load Optimal Settings................................................................................... 30

Load Best Performance Settings.................................................................... 30

Features Setup Page....................................................................................... 30

CPU PnP Setup Page ..................................................................................... 32

Hardware Monitor Page................................................................................. 32

Change Password........................................................................................... 33

Exit ................................................................................................................ 33

CHAPTER 4 34

Using the Mainboard Software 34

About the Software CD-ROM ...................................................................34

Audio Drivers and Software Installation ....................................................34

Utility Software Reference ........................................................................35

Introducing the Mainboard

Congratulations on purchasing the KOB P4X266 NDFSX mainboard. The

KOB P4X266 NDFSX mainboard is an ATX mainboard that uses a 4-layer

printed circuit board and measures 305 mm x 244 mm. The mainboard fea-

tures a Socket 478 that accommodates Intel Pentium 4 processors supporting

system bus (FSB) speeds of 400 MHz.

This mainboard has the VIA VT8753 (V845PRO) Northbridge and VT8233

Southbridge chipsets that support AC’97 audio codec, and provide Ultra

DMA 33/66/100 function. This mainboard has four 32-bit PCI slots, one

4xAGP slot, one CNR (Communications and Networking Riser) slot, and an

onboard 10BaseT/100BaseTX Network interface (optional). In addition, this

mainboard has a full set of I/O ports including two PS/2 ports for mouse and

keyboard, two serial ports, one parallel port, one MIDI/game port and six USB

ports (two backpanel ports, onboard USB headers providing four extra ports).

By means of the Extended USB Module connected to the mainboard, you can

make four extra USB ports.

Compare the mainboard’s package contents with the following checklist:

Standard Items

• One mainboard

• The User’s Manual

• One diskette drive ribbon cable

• One IDE drive ribbon cable

• Software support CD

• One Retention Module

Processor The KOB P4X266 NDFSX mainboard includes a Socket 478

that has the following features:

• Supports up to a 400 MHz system bus (FSB)

• Accommodates Intel Pentium 4 processors.

Chipset There are VT8753 Northbridge and VT8233 Southbridge in

this chipset in accordance with an innovative and scalable

architecture with proven reliability and performance. A few of

the chipset’s advanced features are:

• An advanced V-Link memory controller architecture that

provides the bandwidth up to 266 MB/s and performance

necessary for even the most demanding Internet and 3D

graphics

• Support for an 4xAGP interface providing vivid 3D

graphics and video performance

• An ATA 100 interface on the chipset, which helps boost

system performance by providing a high-speed connec-

tion to ATA 100 Hard Disk Drives, delivering maximum

sustained data transfer rates of 100 MB/sec

Additional key features include support for six USB ports, an

AC 97 link for audio and modem, hardware monitoring, and

ACPI/OnNow power management.

Memory The mainboard accommodates 2 DDR + 2 SDR 168 pin, 3.3V

DIMM sockets with a total capacity of 2 GB system memory.

VGA This mainboard includes a 4xAGP slot that provides eight

times the bandwidth of the original AGP specification. AGP

technology provides a direct connection between the graphics

sub-system and memory so that the graphics do not have to

compete for processor time with other devices on the PCI bus.

AC’ 97 Audio

Codec

The AC’97 Audio codec is compliant with the AC’ 97 2.1 speci-

fication, and supports 18-bit ADC (Analog Digital Converter)

and DAC (Digital Analog Converter) resolution as well as 18-

bit stereo full-duplex codec with independent and variable

sampling rates. Further features include support for four ana-

log line-level stereo inputs.

Expansion

Options

KOB P4X266 NDFSX has four 32-bit PCI slots, an AGP slot, a

CNR (Communications and Networking Riser) slot, and an

onboard PCI LAN interface (optional).

The KOB P4X266 NDFSX PCI slots are capable of Ultra DMA

bus mastering with transfer rates of 33/66/100 MB/sec.

Integrated I/O The mainboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• Two serial ports

• One parallel port

• One MIDI/game port

• Six USB ports (two backpanel ports, onboard

• USB headers providing four extra ports)

• Audio jacks for microphone, line-in and line- out

BIOS

Firmware

This mainboard uses AMI BIOS that enables users to config-

ure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters and memory timing

• CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

Built-in

Ethernet LAN

(optional)

• Built-in 10BaseT/100BaseTX Ethernet LAN

• VT8233 integrates Fast Ethernet MAC and VT6013 LAN

PHY in compliance with IEEE802.3u 100BASE-TX,

10BASE-T and ANSI X3.263 TP-PMD standards

• In compliance with ACPI 1.0 and the Network Device

Class Power Management 1.0

• High Performance achieved by 100Mbps clock generator

and data recovery circuit for 100Mbps receiver

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the ATX system case. Some features on the

mainboard are implemented by cabling connectors on the mainboard to indi-

cators and switches on the system case. Ensure that your case supports all

the features required. The mainboard can support one or two floppy diskette

drives and four enhanced IDE drives. Ensure that your case has sufficient

power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has an ATX form factor of 305 x 244 mm. Choose a case that

accommodates this form factor.

Installing the Mainboard

Follow these safety precautions when installing the mainboard:

• Wear a grounding strap attached to a grounded device to avoid

damage from static electricity.

• Discharge static electricity by touching the metal case of a safely

grounded object before working on the mainboard.

• Leave components in the static-proof bags they came in.

• Hold all circuit boards by the edges. Do not bend circuit boards.

This Quick Guide suggests the steps you can take to assemble your system

with the mainboards.

The following table provides a reference for installing specific components:

Locating Mainboard Components Go to page 4

Installing the Mainboard in a Case Go to page 6

Setting Jumpers Go to page 6

Installing Case Components Go to page 9

Installing the CPU Go to page 10

Installing Memory Go to page 13

Installing a HDD and CD-ROM Drive Go to page 14

Installing a FDD Go to page 15

Installing Add-on Cards Go to page 16

Connecting Options Go to page 17

Connecting Peripheral (I/O) Devices Go to page 19

Refer to the following illustration and instructions for installing the mainboard

in a case:

This illustration shows an ex-

ample of a mainboard being

installed in a tower-type case:

Note: Do not overtighten

the screws as this

can stress the main-

board.

Most system cases have

mounting brackets installed in

the case, which correspond to

the holes in the mainboard.

Place the mainboard over the

mounting brackets and secure

the mainboard onto the mount-

ing brackets with screws.

ecure the mainboard with

screws where appropriate.

1. Place the mainboard

over the mounting brackets.

Ensure that your case has an I/O template that supports the I/O ports and

expansion slots on your mainboard.

This section explains how to set jumpers for correct configuration of the main-

board.

Setting Jumpers

Use the mainboard jumpers to set system configuration options. Jumpers with

more than one pin are numbered. When setting the jumpers, ensure that the

jumper caps are placed on the correct pins.

The illustrations below show a 2-pin jumper.

When the jumper cap is placed on both pins,

the jumper is SHORT. If you remove the

jumper cap, or place the jumper cap on just

one pin, the jumper is OPEN.

This illustration shows a 3-pin

jumper. Pins 1 and 2 are SHORT.

Short Open

123

Inhaltsverzeichnis

Andere PCchips Hauptplatine Handbücher

PCchips

PCchips M925G 8.0 Bedienungsanleitung

PCchips

PCchips Motherboard Bedienungsanleitung

PCchips

PCchips M726MRT Bedienungsanleitung

PCchips

PCchips M765MRT Bedienungsanleitung

PCchips

PCchips M755LMR V7.1 Bedienungsanleitung

PCchips

PCchips M935L Bedienungsanleitung

PCchips

PCchips M925ALU Bedienungsanleitung

PCchips

PCchips M851AG Bedienungsanleitung

PCchips

PCchips M758LMT Bedienungsanleitung

PCchips

PCchips M848ALU Bedienungsanleitung

PCchips

PCchips M938 Series Bedienungsanleitung

PCchips

PCchips M810LMR 3.0x Bedienungsanleitung

PCchips

PCchips M935 Series Bedienungsanleitung

PCchips

PCchips Tidalwave W30 Bedienungsanleitung

PCchips

PCchips M754 Plus Series Bedienungsanleitung

PCchips

PCchips A16 Bedienungsanleitung

PCchips

PCchips M766LMRT Bedienungsanleitung

PCchips

PCchips K7S5A Bedienungsanleitung

PCchips

PCchips M909G Series Bedienungsanleitung

PCchips

PCchips M750 Bedienungsanleitung

PCchips

PCchips M957G Bedienungsanleitung

PCchips

PCchips M922ULR Bedienungsanleitung

PCchips

PCchips M930LR Bedienungsanleitung

PCchips

PCchips M852 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung