PeakTech 3355 Bedienungsanleitung

PeakTech

3355 / 3360

Bedienungsanleitung /

operation manual /

Mode d’emploi /

Istruzioni per l uso /

Manual de instrucciones

Digital Multimeter /

Multimètre digital /

Multimetro digitale /

Multímetro digital

1. Safety Precautions

This product complies with the requirements of the following

European Community Directives: 2004/108/EC (Electromagnetic

Compatibility) and 2006/95/EC (Low Voltage) as amended by

2004/22/EC (CE-Marking). Overvoltage category III 1000V; over-

voltage category IV 600V; pollution degree 2.

CAT I: For signal level, telecommunication, electronic with small

transient over voltage

CAT II: For local level, appliances, main wall outlets, portable

equipment

CAT III: Distribution level, fixed installation, with smaller transient

over-voltages than CAT IV.

CAT IV: Units and installations, which are supplied overhead lines,

which are stand in a risk of persuade of a lightning, i.e.

main-switches on current input, over-voltage-diverter,

current use counter.

To ensure safe operation of the equipment and eliminate the

danger of serious injury due to short-circuits (arcing), the following

safety precautions must be observed.

Damages resulting from failure to observe these safety precautions

are exempt from any legal claims whatever.

* Do not use this instrument for high-energy industrial installation

measurement. This instrument is intended for use in installation

over-voltage category III.

* Do not exceed the maximum permissible input ratings (danger

of serious injury and/or destruction of the equipment).

-34-

* The meter is designed to withstand the stated max voltages. If it

is not possible to exclude without that impulses, transients,

disturbance or for other reasons, these voltages are exceeded

a suitable prescale (10:1) must be used.

* Replace a defective fuse only with a fuse of the original rating.

Never short-circuit fuse or fuse holding.

* Disconnect test leads or probe from the measuring circuit

before switching modes or functions.

* Do not conduct voltage measurements with the test leads

connected to the mA/A- and COM-terminal of the equipment.

* The 10A-range is protected. To avoid damage or injury, use the

meter only in circuits limited by fuse or circuit breaker to 10A or

2000VA.

* To avoid electric shock, disconnect power to the unit under test

and discharge all capacitors before taking any resistance

measurements.

* Do not conduct current measurements with the leads connected

to the V/Ω-terminals of the equipment.

* Check test leads and probes for faulty insulation or bare wires

before connection to the equipment.

* To avoid electric shock, do not operate this product in wet or

damp conditions. Conduct measuring works only in dry clothing

and rubber shoes, i. e. on isolating mats.

* Never touch the tips of the test leads or probe.

* Comply with the warning labels and other info on the

equipment.

* Always start with the highest measuring range when measuring

unknown values.

* Do not subject the equipment to direct sunlight or extreme

temperatures, humidity or dampness.

* Do not subject the equipment to shocks or strong vibrations.

* Do not operate the equipment near strong magnetic fields

(motors, transformers etc.).

* Keep hot soldering irons or guns away from the equipment.

* Allow the equipment to stabilize at room temperature before

taking up measurement (important for exact measurements).

* Do not input values over the maximum range of each

measurement to avoid damages of the meter.

-35-

* Do not turn the rotary function switch during voltage or current

measurement, otherwise the meter could be damaged.

* Use caution when working with voltages above 35 V DC or

25 V AC. These Voltages pose shock hazard.

* Replace the battery as soon as the battery indicator “BAT”

appears. With a low battery, the meter might produce false

reading that can lead to electric shock and personal injury.

* Fetch out the battery when the meter will not be used for long

period.

* Periodically wipe the cabinet with a damp cloth and mid

detergent. Do not use abrasives or solvents.

* The meter is suitable for indoor use only

* Do not operate the meter before the cabinet has been closed

and screwed safely as terminal can carry voltage.

* Do not store the meter in a place of explosive, inflammable

substances.

* Do not modify the equipment in any way

* Do not place the equipment face-down on any table or work

bench to prevent damaging the controls at the front.

* Opening the equipment and service – and repair work must only

be performed by qualified service personnel

* Measuring instruments don’t belong to children hands.

1.1. Input limits

Input limits 1000 V DC/AC

rms

less than

10 sec.

mA range AC/DC

400 mA AC/DC 1000 V / 0,5 A

(fused)

A range

10 A AC/DC 1000 V / 10 A

(fused)

Frequency, Resistance,

Capacitance, Duty Cycle, Diode

test, Continuity and

Temperature

600 V AC/DC

rms

(P 3355)

1000 V AC/DC

rms

(P 3360)

-36-

1.2. Safety Symbols

This symbol adjacent to another symbol, terminal or

operating device indicates that the operator must refer to

an explanation in the operating instructions to avoid

personal injury or damage to the meter.

This symbol advices the user that the terminals so

marked must not be connected to a circuit point at which

the voltage, with respect to earth ground, exceeds (in this

case) 1000 V AC or VDC

This symbol adjacent to one or more terminals identifies

them as being associated with ranges that may, in normal

use, be subjected to particulary hazardous voltages. For

maximum safety, thermometer and its test leads should

not be handled when these terminals are energized.

Indicates protection class II, double insulation

IP67

Dust- and waterproof

µA

The maximum current that can measure with this

terminal is 400 mA AC/DC. This terminal is protected by

500 mA/1000 V fuse

The maximum current that can measure with this terminal

is 10 A AC/DC. This terminal is protected by 10 A/1000 V

fuse.

-37-

CAUTION!

Note on using the supplied safety test leads according the

IEC / EN 61010-031:2008:

Measurements in the field of overvoltage category CAT I or CAT II

can be performed with test leads without sleeves with a maximum

of up to 18mm long, touchable metallic probe, whereas for

measurements in the field of overvoltage category CAT III or CAT

IV test leads with put on sleeves, printed with CAT III and CAT IV

must be used, and therefore the touchable and conductive part of

the probes have only max. 4mm of length.

CAUTION !

This CAUTION symbol indicates a potentially hazardous situation,

which if not avoided, may result in minor or moderate injury, or

damage to the product or other property.

2. Technical Data

2.1. Specifications

Display P 3355

26 mm , 3 ¾ digit, 4000 counts with

automatic polarity indication and

backlight

P 3360

19 mm, 4 ¾ digit, 40000 county with

automatic polarity indication, backlight

and 42 segment bargraph

Overrange indicaton: "OL"

Low battery indication: Battery symbol indicates low battery

condition (P 3360)

Measuring rate: 2 times / sec.

-38-

Auto / manual Ranging

Auto power off: about 15 min.

P 3360 : It is possible to turn off the APO (find on

page 53)

Overload protection: on all ranges

measuring functions: True RMS measurement (only P 3360)

Auto- or manual range selection

Data Hold

Relative zero

Min/Max and Peak-Hold (only P 3360)

Overload protection: on all ranges

Operating Temperature: 41°F to 104°F (5°C to 40°C)

Storage Temperature: -4°F to 140°F (-20...+60°C)

Accuracy Temperature: 64°F to 82°F (18°C to 28°C) to

maintain guaranteed accuracy

Relative Humidity: < 80% operating

Dimensions (W x H x D): 85 x 185 x 55 mm

Weight: approx. 400 g

Power source: 9 V battery (Neda 1604)

Accessories supplied: Operation manual, test leads, socket

seals, Battery, K-type thermocouple,

Adaptor for thermocouple, carrying

case

-39-

2.2. Electrical Specifications

DC Volts

Model

Range

Resolution

Accuracy

P 3355 400 mV 100 µV

0,5% rdg. + 2 dgt

4 V 1 mV

±1,2% r dg. + 2 dgt

40 V 10 mV

400 V 100 mV

1000 V 1 V

1,5% rdg. + 2 dgt

P 3360 400 mV 10 µV

4 V 100 µV

0,06% rdg. + 2 dgt

40 V 1 mV

400 V 10 mV

1000 V 100 mV

0,1% rdg. + 5 dgt

Overload protection 1000V AC/DC

rms

Input Impedance: (P 3355) 7,8 MΩ/ (P 3360) 10 MΩ

AC Volts

Model

Range

Resolution

Accuracy

P 3355 400 mV 100 µV

1,0% rdg. + 5 dgt

4 V 1 mV

±1,0% rdg. + 3 dgt

40 V 10 mV

400 V 100 mV

1000 V 1 V

P 3360 400 mV 100 µV

1,0% rdg. + 5 dgt

4 V 1 mV

±1,0% v.M. + 3 dgt

40 V 10 mV

400 V 100 mV

1000 V 1 V

Overload protection 1000V AC/DC

rms

Input Impedance: (P 3355) 7,8 MΩ/ (P 3360) 3 MΩ

AC Response: (P 3355) 50 to 400Hz / (P 3360) 50 to

1000Hz

-40-

DC Current

Model

Range

Resolution

Accuracy

P 3355 400 µA 0,1 µA

1,0 % rdg. + 3 dgt.

4000 µA 1 µA .

40 mA 10 µA

1,5% rdg. + 3 dgt.

400 mA 100 µA

10 A 10 mA

2,5% rdg. + 5 dgt.

P 3360 400 µA 0,01 µA

4000 µA 0,1 µA .

40 mA 1 µA

1,0% rdg. + 3 dgt.

400 mA 10 µA

10 A 1 mA

Overload protection: 0,5A / 1000V and 10A / 1000V

Max. Input: 400mA DC on mA – ranges and

10A on A – range

AC current

Model

Range

Resolution

Accuracy

P 3355 400 µA 0,1 µA

1,5 % rdg. + 5 dgt.

4000 µA 1 µA .

40 mA 10 µA

1,8% rdg. + 5 dgt.

400 mA 100 µA

10 A 10 mA

3,0% rdg. + 7 dgt.

P 3360 400 µA 0,1 µA

4000 µA 1 µA .

40 mA 10 µA

1,5% rdg. + 3 dgt.

400 mA 100 µA

10 A 10 mA

Overload protection: 0,5A / 1000V and 10A / 1000V

Max. input: 400mA DC on mA – Range and

10A on A – Range

AC Response : (P 3355) 50 to 400Hz /

(P 3360) 50 to 1000Hz

-41-

Resistance

Model

Range

Resolution

Accurac

P 3355 400

Ω

100 m

Ω

1,2% rdg. + 4 dgt.

4 k

Ω

1,0% rdg. + 2 dgt.

40 k

Ω

±1,2% rdg. + 2 dgt

400 k

Ω

100

Ω

4 M

Ω

1 k

Ω

40 M

Ω

10 k

Ω

2,0% rdg. + 3 dgt.

P 3360 400

Ω

10 m

Ω

0,3% rdg. + 9 dgt.

4 k

Ω

100 m

Ω

±0,3% rdg. + 4 dgt.

40 k

Ω

400 k

Ω

4 M

Ω

100

Ω

40 M

Ω

1 k

Ω

2,0% rdg. + 10 dgt.

Overload protection: 600 V DC/AC

rms

Capacitance

Model

Range

Resolution

Accuracy

P 3355 4 nF 1 pF

5,0% rdg. + 20 dgt

40 nF 10 pF

5,0% rdg. + 7 dgt

400 nF 100 pF

±3,0% rdg. + 5 dgt

4 µF 1 nF

40 µF 10 nF

100 µF 100 nF

5,0% rdg. + 5 dgt

P 3360 40 nF 1 pF

3,5% rdg. + 40 dgt

400 nF 10 pF

4 µF 100 pF

±3,5% rdg. + 10 dgt

40 µF 1 nF

400 µF 10 nF

4000 µF 100 nF

5,0% rdg. + 10 dgt

40 mF 1 µF

Overload protection: 600 V DC/AC

rms

-42-

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PeakTech Multimeter Handbücher

PeakTech

PeakTech 1070 Bedienungsanleitung

PeakTech

PeakTech 3336 Bedienungsanleitung

PeakTech

PeakTech 4090 Bedienungsanleitung

PeakTech

PeakTech 4390 Bedienungsanleitung

PeakTech

PeakTech 2015 Bedienungsanleitung

PeakTech

PeakTech 3315 USB Bedienungsanleitung

PeakTech

PeakTech 3320 Bedienungsanleitung

PeakTech

PeakTech 1020 Bedienungsanleitung

PeakTech

PeakTech 3340 Bedienungsanleitung

PeakTech

PeakTech 2005 Bedienungsanleitung

PeakTech

PeakTech 3340 Bedienungsanleitung

PeakTech

PeakTech 3380 Bedienungsanleitung

PeakTech

PeakTech 1075 Bedienungsanleitung

PeakTech

PeakTech 1020 A Bedienungsanleitung

PeakTech

PeakTech 1080 Bedienungsanleitung

PeakTech

PeakTech 2015 Bedienungsanleitung

PeakTech

PeakTech 2025 A Bedienungsanleitung

PeakTech

PeakTech 3450 Bedienungsanleitung

PeakTech

PeakTech 2015 A Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

PeakTech

PeakTech 3385 Bedienungsanleitung

PeakTech

PeakTech 3131eff Bedienungsanleitung

PeakTech

PeakTech 1070 Bedienungsanleitung

PeakTech

PeakTech 3385 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung

Morris

Morris 57074 Bedienungsanleitung