Peavey KB2 Bedienungsanleitung

For more information on other great Peavey products, go to your local Peavey dealer or online at www.peavey.com.

KB2/KB3Keyboard Amplifier Owner Manual

Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to constitute a ris of electric shoc to persons.

Intended to alert the user of the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the product.

CCAAUUTTIIOONN::Ris of electrical shoc — DO NOT OPEN!

CCAAUUTTIIOONN::To reduce the ris of electric shoc , do not remove cover. No user serviceable parts inside.

Refer servicing to qualified service personnel.

WWAANNIINNGG::To prevent electrical shoc or fire hazard, do not expose this appliance to rain or moisture.

Before using this appliance, read the operating guide for further warnings.

Este símbolo tiene el propósito, de alertar al usuario de la presencia de “(voltaje) peligroso” sin

aislamiento dentro de la caja del producto y que puede tener una magnitud suficiente como para

constituir riesgo de descarga eléctrica.

Este símbolo tiene el propósito de alertar al usario de la presencia de instruccones importantes sobre la

operación y mantenimiento en la información que viene con el producto.

PPEECCAAUUCCIIOONN::Riesgo de descarga eléctrica ¡NO ABRIR!

PPEECCAAUUCCIIOONN::Para disminuír el riesgo de descarga eléctrica, no abra la cubierta. No hay piezas útiles

dentro. Deje todo mantenimiento en manos del personal técnico cualificado.

AADDVVEETTEENNCCIIAA::Para evitar descargas eléctricas o peligro de incendio, no deje expuesto a la lluvia o

humedad este aparato Antes de usar este aparato, Iea más advertencias en la guía de operación.

Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur la présence d’une tension dangereuse

pouvant être d’amplitude suffisante pour constituer un risque de choc électrique.

Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur qu’il ou qu’elle trouvera d’importantes

instructions concernant l’utilisation et l’entretien de l’appareil dans le paragraphe signalé.

AATTTTEENNTTIIOONN::Risques de choc électrique — NE PAS OUVRIR!

AATTTTEENNTTIIOONN::Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à

l’intérieur aucune pièce pouvant être reparée par l’utilisateur. Confiez I’entretien et la réparation de

l’appareil à un réparateur Peavey agréé.

AAVVEETTIISSSSEEMMEENNTT: Afin de prévenir les risques de décharge électrique ou de feu, n’exposez pas cet

appareil à la pluie ou à l’humidité. Avant d’utiliser cet appareil, lisez attentivement les avertissements

supplémentaires de ce manuel.

Dieses Symbol soll den Anwender vor unisolierten gefährlichen Spannungen innerhalb des Gehäuses

warnen, die von Ausreichender Stär e sind, um einen ele trischen Schlag verursachen zu önnen.

Dieses Symbol soll den Benutzer auf wichtige Instru tionen in der Bedienungsanleitung aufmer sam

machen, die Handhabung und Wartung des Produ ts betreffen.

VVOOSSIICCHHTT:: Risi o — Ele trischer Schlag! Nicht öffnen!

VVOOSSIICCHHTT:: Um das Risi o eines ele trischen Schlages zu vermeiden, nicht die Abdec ung enfernen. Es

befinden sich eine Teile darin, die vom Anwender repariert werden önnten. Reparaturen nur von

qualifiziertem Fachpersonal durchführen lassen.

AACCHHTTUUNNGG::Um einen ele trischen Schlag oder Feuergefahr zu vermeiden, sollte dieses Gerät nicht dem

Regen oder Feuchtig eit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

IIMMPPOORRTTAANNTT SSAAFFEETTYY IINNSSTTRRUUCCTTIIOONNSS

WWAANNIINNGG::When using electrical products, basic cautions should always be followed, including the following:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not bloc any of the ventilation openings. Install in accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third

prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being wal ed on or pinched, particularly at plugs, convenience receptacles, and the

point they exit from the apparatus.

11. Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your

plug‚ proceed as follows:

a) The wire that is colored green and yellow must be connected to the terminal that is mar ed by the letter E‚ the

earth symbol‚ colored green or colored green and yellow.

b) The wire that is colored blue must be connected to the terminal that is mar ed with the letter N or the color blac .

c) The wire that is colored brown must be connected to the terminal that is mar ed with the letter L or the color red.

12. Only use attachments/accessories provided by the manufacturer.

13. Use only with a cart, stand, tripod, brac et, or table specified by the manufacturer, or sold with the apparatus. When

a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

14. Unplug this apparatus during lightning storms or when unused for long periods of time.

15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

16. Never brea off the ground pin. Write for our free boo let “Shoc Hazard and Grounding.” Connect only to a power

supply of the type mar ed on the unit adjacent to the power supply cord.

17. If this product is to be mounted in an equipment rac , rear support should be provided.

18. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in

susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently

intense noise for a sufficient time. The U.S. Government’s Occupational and Health Administration (OSHA) has

specified the following permissible noise level exposures:

Duration Per Day In Hours Sound Level dBA, Slow Response

890

692

495

397

2 100

⁄

102

1 105

⁄

110

⁄

or less 115

According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the

ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure

is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is

recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be

protected by hearing protectors while this unit is in operation.

SSAAVVEE TTHHEESSEE IINNSSTTUUCCTTIIOONNSS!!

KKBB®®22//KKBB33

Keyboard Amplifiers

Than you for selecting the KB2/KB3 eyboard amplifier. Once again‚ Peavey engineers have listened to input from

eyboard players and put together an amplifier that combines excellent features and sound in one portable pac age. The

KB Series amplifiers deliver awesome sound reproduction for all of your eyboard sounds—from thundering bass to

crystal highs—it’s all there!

Before you begin to play through your amp, it is very important to ensure the product has the proper AC line voltage

supplied. You can find the proper voltage for your amp printed next to the IEC line (power) cord on the rear panel of the

unit. For the KB3, an external spea er jac is provided for the additional use of an external spea er enclosure. This

feature is located on the rear panel as well and is also explained in this section. Each product feature is numbered. Refer

to the control and rear panel diagrams in this manual to locate the particular features next to their number.

Please read this guide carefully to ensure your personal safety as well as the safety of your amplifier.

FFeeaattuurreess

· 4-channels (KB2 and KB3)

· KB2: biamped 45 watts and 12 watts

· KB3: 80 watts external‚ 60 watts internal

· balanced line out

· effects send/return jack

· external speaker capability (KB3 only)

EENNGGLLIISSHH

QQUUIICCKK SSEETT--UUPP GGUUIIDDEE

1. Connect the line cord to the appropriately rated receptacle

2. Be certain that all levels are down or set to the fully counter-cloc wise position and set

all the EQs flat

3. Set the master level to the 12:00 position

4. Connect left output of your eyboard to the left input of the KB2/KB3 and connect right

output of your eyboard to the right input of the KB2/KB3

5. Set the DDT switch to the enable position

6. Set the main/monitor switch to the monitor position

7. Turn on power to the KB2/KB3

8. Adjust the channel level for proper volume

9. Adjust the channel EQ as needed

((11)) LLeevveell

Controls the 1/4" jac input level on channels 1 and 2 and the 1/4" jac input and XLR input on channel 3.

((22)) LLooww EEQQ

An active tone control (shelving type: +/-15 dB) that varies the low frequency range.

CCaauuttiioonn:: Excessive low frequency boost causes greater power consumption and increases the

possibility of speaker damage.

((33)) HHii EEQQ

An active tone control (shelving type: ± 15 dB) that varies the hi frequency range.

((44)) MMiidd EEQQ

An active tone control (pea /notch type: ± 15dB) that varies the mid frequencies. (channel 3)

((55)) CCHH44//MMoonniittoorr LLeevveell

Controls the input level for channel 4. Controls high-impedance microphones or other high-level sources

equipped with a 1/4" phone plug.

((66)) HHeeaaddpphhoonnee LLeevveell ((KKBB33 oonnllyy))

This sets the level to the headphone jac on the rear panel. To avoid damage to your hearing‚ ma e sure

to turn the dial fully counter-cloc wise before using headphones. Slowly turn the nob cloc wise until a

comfortable listening level is set. This does not affect the master level.

((77)) MMaasstteerr LLeevveell ((KKBB33 oonnllyy))

This nob sets the overall level for the unit. Ma e sure the Master level is completely down (full counter-

cloc wise) before powering up the unit. This does not affect the headphone level.

((88)) PPoowweerr SSwwiittcchh

This two-way roc er switch applies power to the unit when placed in the ON position.

FFRROONNTT PPAANNEELL

1 5 6

2 3 4 7 8

RREEAARR PPAANNEELL

MMaaiinn LLiinnee OOuutt ((99))

This low-noise‚ electronically-balanced XLR connector can be used to route signals to a mixing

console‚ recording device‚ etc.

SSeenndd//RReettuurrnn JJaaccss MMaaiinnss ((1100 && 1111))

This pair of 1/4" jac s allow the use of various auxiliary units (effects units‚ equalizers‚ etc.) in-line‚

before the power amp section.

HHeeaaddpphhoonnee JJaacc ((1122))

This 1/4" jac accepts stereo headphones only.

CCHH44//MMoonniittoorr IInnppuutt JJaacc ((1133))

Use this 1/4" jac to connect to the output of any line-level device.

CChhaannnneell:: 33 LLooww--IImmppeeddaannccee IInnppuutt ((1144))

For use with low-impedance microphones or other line-level sources equipped with a male XLR

connector.

CChhaannnneellss 33‚‚ 22 &&11 ((1155))

These 1/4" jac s accept high-impedance microphones or line-level sources equipped with 1⁄4" phone plugs.

EExxtteerrnnaall SSppeeaaeerr JJaacc ((1166)) ((KKBB33 oonnllyy))

This 1/4" jac provides the powered signal from the amplifier. Use this jac to add a second spea er

cabinet in parallel. The external minimum spea er load impedance is 8 ohms.

IIEECC ccoonnnneeccttoorr//ddeettaacchhaabbllee lliinnee ccoorrdd ((1177))

This is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings

for the intended operating voltage is included in the carton. The mains cord should be connected to

the amplifier before connecting to a suitable AC outlet.

UU..SS.. DDoommeessttiicc AACC MMaaiinnss CCoorrdd

The mains cord supplied with the unit is heavy-duty‚ 3-conductor type with a conventional 120 VAC

plug with ground pin. Never brea off the ground pin on any equipment. It is provided for your safety.

If the outlet used does not have a ground pin‚ a suitable grounding adapter should be used and the

third wire should be properly grounded.

17 91412

10 11 13 15

KKBB22//33 BBlloocc DDiiaaggrraamm

PPRREEAAMMPP SSEECCTTIIOONN

The following preamp specs are

measured @ kHz‚ nominal signal

levels are with channel level controls

set at 5‚ minimum levels are with

channel level controls set at 0.

CChhaannnneell 11 && 22 IInnppuuttss::

Input Impedance: 100

Nominal Input Level: 6 dBV‚ 2 V RMS

Minimum Input Level: -10 dBV‚ 316 mV RMS

CChhaannnneell 33 IInnppuutt::

Low Z Input Impedance: 10 Ohms

Nominal Input Level: -15 dBV‚ 178 mV RMS

Minimum Input Level: -33 dBV‚ 22 mV RMS

High Z Input Impedance: 75

Nominal Input Level: -15 dBV‚ 178 mV RMS

Minimum Input Level: -33 dBV‚ 22 mV RMS

CChhaannnneell 44 IInnppuutt::

Input Impedance: 10 Ohms

Nominal Input Level: 0 dBV‚ 1 V RMS

Minimum Input Level: -25 dBV‚ 56 mV RMS

HHeeaaddpphhoonnee OOuuttppuutt

Load Impedance: 8 Ohms or greater

Nominal Output: 100 mW RMS

MMaaiinn LLiinnee OOuutt

Output Impedance: <100

Output Level: 18 dBV

PPOOWWEERR AAMMPPLLIIFFIIEERR SSEECCTTIIOONN

aatteedd PPoowweerr && LLooaadd::

80 W RMS/4 Ohms or 60 W RMS/8 Ohms

(1 Hz, 1% THD @ 120 VAC line)

FFrreeqquueennccyy RReessppoonnssee::

+0, -1 dB, 20Hz–20 Hz @ 30 W RMS/8 Ohms

DDDDTT DDyynnaammiicc RRaannggee::

Greater than 20 dB

DDDDTT MMaaxxiimmuumm TTHHDD::

Below 0.5% THD for 6 dB overload

Below 1% THD for 20 dB overload

HHuumm && NNooiissee::

Greater than 100 dB below rated power

PPoowweerr CCoonnssuummppttiioonn::

120 W @ 120V AC‚ 50/60 Hz‚ Domestic

120 W @ 220–230/240V AC‚ 60 Hz‚ Export

KKBB®®33

SSPPEECCIIFFIICCAATTIIOONNSS

PPRREEAAMMPP SSEECCTTIIOONN

The following preamp specs are

measured @ kHz‚ nominal signal

levels are with channel level controls

set at 5‚ minimum levels are with

channel level controls set at 0.

CChhaannnneell 11 && 22 IInnppuuttss::

Input Impedance: 100

Nominal Input Level: 1.5 dBV‚ 1.2 V RMS

Minimum Input Level: -16 dBV‚ 158 mV RMS

CChhaannnneell 33 IInnppuutt::

Low Z Input Impedance: 10 Ohms

Nominal Input Level: -21 dBV‚ 89 mV RMS

Minimum Input Level: -38 dBV‚ 13 mV RMS

High Z Input Impedance: 75

Nominal Input Level: -21 dBV‚ 89 mV RMS

Minimum Input Level: -38 dBV‚ 13 mV RMS

CChhaannnneell 44 IInnppuutt::

Input Impedance: 10 Ohms

Nominal Input Level: 0 dBV‚ 1 V RMS

Minimum Input Level: -25 dBV‚ 56 mV RMS

HHeeaaddpphhoonnee OOuuttppuutt

Load Impedance: 8 Ohms or greater

Nominal Output: 100 mW RMS

MMaaiinn LLiinnee OOuutt

Output Impedance: <100

Output Level: 18 dBV

PPOOWWEERR AAMMPPLLIIFFIIEERR SSEECCTTIIOONN

aatteedd PPoowweerr && LLooaadd::

45 W RMS/8 Ohms/low channel

12 W RMS/8 Ohms/high channel

(1 Hz, 1% THD @ 120 VAC line)

DDDDTT DDyynnaammiicc RRaannggee::

Greater than 20 dB

DDDDTT MMaaxxiimmuumm TTHHDD::

Below 0.5% THD for 6 dB overload

Below 1% THD for 20 dB overload

HHuumm && NNooiissee::

Greater than 90 dB below rated power

PPoowweerr CCoonnssuummppttiioonn::

150 W @ 120V AC‚ 50/60 Hz‚ Domestic

150 W @ 220–230/240V AC‚ 60 Hz‚ Export

CCrroossssoovveerr::

Fixed‚ 18 dB/octave‚ 3.5 Hz crossover

frequency

KKBB®®22

SSPPEECCIIFFIICCAATTIIOONNSS

NOTES:

Andere Handbücher für KB2

Dieses Handbuch passt für folgende Modelle

Andere Peavey Verstärker für Musikinstrumente Handbücher

Peavey

Peavey Basic 50 Bedienungsanleitung

Peavey

Peavey BACKSTAGE 50 Bedienungsanleitung

Peavey

Peavey Programax 10 Bedienungsanleitung

Peavey

Peavey Lo Max 15 Bedienungsanleitung

Peavey

Peavey Spectrum Bass II Bedienungsanleitung

Peavey

Peavey Audition Bedienungsanleitung

Peavey

Peavey Vintage Bedienungsanleitung

Peavey

Peavey 115 TXR Bedienungsanleitung

Peavey

Peavey Butcher Bedienungsanleitung

Peavey

Peavey BACKSTAGE 50 Bedienungsanleitung

Peavey

Peavey Deltabass Deltabass Bedienungsanleitung

Peavey

Peavey Reno 400 Bedienungsanleitung

Peavey

Peavey Transtube 112/212 EFX Bedienungsanleitung

Peavey

Peavey MicroBass Bass Amplification System Bedienungsanleitung

Peavey

Peavey Ecoustic E208 Bedienungsanleitung

Peavey

Peavey Tour TKO 115 Bedienungsanleitung

Peavey

Peavey XXL 212 Bedienungsanleitung

Peavey

Peavey The Classic Bedienungsanleitung

Peavey

Peavey JSX JSXTM Mini ColossalTM Class A Tube Guitar... Bedienungsanleitung

Peavey

Peavey Mark III 300 CHS Bedienungsanleitung

Peavey

Peavey Basic 112 Bedienungsanleitung

Peavey

Peavey Basic 60 Bedienungsanleitung

Peavey

Peavey Mini MEGA Bedienungsanleitung

Peavey

Peavey Triumph PAG 60 Bedienungsanleitung

Beliebte Verstärker für Musikinstrumente Handbücher anderer Marken

acus

acus One Forstreet 10 Bedienungsanleitung

Marshall Amplification

Marshall Amplification MG10KK Bedienungsanleitung

Pyle Pro

Pyle Pro PPG860A Bedienungsanleitung

Laney

Laney BC30 Bedienungsanleitung

Vox

Vox Pathfinder 15SMR Bedienungsanleitung

Marshall Amplification

Marshall Amplification JVM205C Bedienungsanleitung

Crate

Crate Professional BV-120H Bedienungsanleitung

Fender

Fender Bassman 1200 Bedienungsanleitung

ZT Club Bedienungsanleitung

Ibanez

Ibanez IFS2X Bedienungsanleitung

Crate

Crate GLX1200H Bedienungsanleitung

Laboga

Laboga THE BEAST Bedienungsanleitung

Falken1

Falken1 Traveller Pro Bedienungsanleitung

Hughes & Kettner

Hughes & Kettner Bass Kick 303 Bedienungsanleitung

Yamaha

Yamaha GA-10 Bedienungsanleitung

Engl

Engl Powerball-2 Service-Handbuch

Gibson

Gibson GA5WTR Kurzanleitung

Engl

Engl Powerball-2 Bedienungsanleitung