Peavey PROCOMM Bedienungsanleitung

www.peavey.com

PROCOMM® 2.4 GHz

Digital Wireless Transmitters

Operating

Manual

FCC/ICESCompliancyStatement

FCCID:I4S-PCXDBP

FCCID:I4S-PCXDHT

ThisdevicecomplieswithPart15oftheFCCrulesandIndustryCanadalicense-exemptRSSStandard(s).Operationis

subjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemust

acceptanyinterferencereceived,thatmaycauseundesiredoperation.

LeprésentappareilestconformeauxCNRd’lndustrieCanadaapplicablesauxappareilsradioexemptsde

licence.L’exploitationestautoriséeauxdeuxconditionssuivantes:(1)I’appareilnedoitpasproduirede

brouillage,et(2)I’utilisateurdeI’appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesile

brouillageestsusceptibled’encompromettrelefonctionnement.

Caution:ChangesormodificationstotheequipmentnotapprovedbyPeaveyElectronicsCorp.canvoidthe

user’sauthoritytousetheequipment.

Note–ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,

pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio

frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful

interferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurina

particularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,

whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotryandcorrectthe

interferencebyoneormoreofthefollowingmeasures.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

The equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment.

Prudence:Lesmodificationsapportées àl'équipementnonapprouvésparPeaveyElectronicsCorp.

peuventannulerledroitdel'utilisateuràutiliserl'équipement.

IC:3642A-PCXDBP

IC:3642A-PCXDHT

L'exposition aux radiations

L'équipement est conforme aux limites d'exposition aux radiations d'Industrie

Canada définies pour un environnement non contrôlé.

FCC Radiation Exposure Statement(for Model number: PCX-D HT)

This equipment complies with FCC &IC RSS-102 RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 1.5 centimeters

between the radiator and your body.

is transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The antennas used for this transmitter must be installed to provide a separation distance of at least 1.5 cm

from all persons and must not be co-located or operating in conjunction with any other antenna or

transmitter.

Déclaration d’exposition à la radiation:

Cet équipement respecte les limites d’exposition aux rayonnements IC RSS-102 dénies pour un environnement

non contrôlé. Cet équipement doit être installé et mis en marche à une distance minimale de 1.5 cm qui sépare

l’élément rayonnant de votre corps.

FCC Radiation Exposure Statement(for Model number: PCX-D BP)

This equipment complies with FCC &IC RSS-102 RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 1 centimeters

between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The antennas used for this transmitter must be installed to provide a separation distance of at least 1 cm from

all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Déclaration d’exposition à la radiation:

Cet équipement respecte les limites d’exposition aux rayonnements IC RSS-102 dénies pour un environnement

non contrôlé. Cet équipement doit être installé et mis en marche à une distance minimale de 1 cm qui sépare

l’élément rayonnant de votre corps.

PRO COMM® 2.4 GHz Digital Wireless System

PRO COMM Rechargeable Handheld Transmitter

PRO COMM Rechargeable Bodypack Transmitter

Contains lithium ion batteries. Lithium

ion batteries contain Perchlorate-special

handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

WARNING:

Lithium Ion batteries may be a re hazard.

Do not expose to open ame or excessive heat.

WARNING:

Controls and Indicators

1. Capsule Module: e anti-roll grille protects detachable microphone capsule and the internal foam prevents

breathing, wind and POP noises.

2. Fixed Ring

3. Battery Compartment: Accommodates one 18500 rechargeable battery.

4. Housing: Protects transmitter PCB, battery compartment and battery.

5. Ascertain the power is turn “ON” to see battery status.

 Normal Battery: LEDs indicates battery meters.

 Weak Battery: Red LED is lit. Recharge or insert a new recharged battery.

 No LEDs light: battery is completely drained or polarity inserted incorrectly.

6. Power On/O Switch: Always power o the transmitter to conserve battery life when not in use.

7. CCS Infrared (IR) Sync Port: Receives signals from receiver to synchronize frequencies automatically.

8. Battery Charging Contact: Align contacts during charging.

9. Color Coded Protection Cap: Protects against accidental power on/o. Available in dierent colors for channel

dierentiation.

Operating instructions for insertion& removing battery

1. Remove grill in counter clock direction.

2. Press and hold both sides of microphone capsule module and remove gently.

3. Ascertain the battery is inserted according to its correct polarity. A click is heard once correctly inserted

and grill can be closed properly. No click is heard and grill cannot be closed properly if battery is inserted

with the wrong polarity.

NOTE:

Transmitter cannot be powered on with a charged battery.

a. Check for correct polarity insertion. (+ facing up)

b. If inserted with correct polarity and still cannot be powered on it could be due to battery protection

mechanism is in eect. Insert the whole transmitter back to the battery charger for 10 seconds to

“wake-up” and power on again.

c. If battery charger is not used, reverse battery polarity for 10 seconds and then re-inserted with correct

polarity to wake up the battery. Power on again.

Operating Instructions

1. Power On & O

a. Power On: Push the ON/OFF switch to the “ON” location, the battery indicators will light.

b. Power O: Push the ON/OFF switch back, the battery indicators will go out.

2. Battery Status Display

a. Red LED indicator is lit when battery is too low. Please recharge or insert a new recharged battery. e

microphone will be shut down automatically if the battery keeps low status

100% 75% 50% 25%

(green indicator)(red indicator)

Rear Cap has an On/O Switch Protection

e patented color rear cap serves two purposes; it provides easy channel identication and protects the on/

o switch. It is designed to allow the on/o switch to either be exposed or concealed as desired. You can avoid

unintended switching o of the microphone by rotating the color rear cap 180 degrees to x the on/o switch.

e cap can be removed by gripping it rmly and pulling; be sure to push it rmly into place when replacing it

on the microphone.

Note: During microphone usage, the color rear cap must be installed.

Press both sides and pull out to remove the rear cap

Turn the rear cap 180 degree and insert back

e ON/OFF switch is immovable

General Tips for Improving System Performance

1. Performer should avoid holding the microphone over or near the antenna section as this will deteriorate

transmission eciency. Severe deterioration if performer directly covers up the antenna section with both hands.

2. Many performers tend to hold the microphone by the top grille. Unfortunately, this position seriously

degrades both the sound quality and directionality of a microphone. Even the most expensive microphones will

have its original sound quality compromised by this method. Grabbing a microphone by the grille will isolate

the capsule’s acoustic resonance circuit or change the capsule resonator’s frequency. is results in an inferior

performance in both frequency response and the separation of directionality. In addition, a palm’s sound-

focusing eect will tend to strengthen resonances in certain frequencies and can cause unwanted echo.

3. A proper technique is required for using directional microphones because the distance between the

microphone and your mouth has a signicant impact on sensitivity and performance. ere is an inverse

relationship between microphone sensitivity and the distance from the mouth to the microphone. Consequently,

performers with a ‘’weaker’’ sound level cannot expect to hold the microphone too far away from their mouth

and compensate by turning up the amplier volume to increase the sound level as this can easily cause echo or

feedback. In contrast, performers with a ‘’louder’’ sound level should not hold the microphone too close as this

can easily result in distortion by causing the amplier system to be overloaded.

4. Furthermore, a large-diaphragm directional microphone has a very distinct proximity eect. When

the microphone is close to the mouth, the bass response is strengthened as the distance gets closer. erefore,

if a performer’s sound is insucient in bass, they can hold the microphone closer and use the proximity eect

to help compensate for the lower bass level. Conversely, if a performer’s voice is too heavy in the bass register,

increasing the distance between the microphone and their mouth will decrease the proximity eect and reduce

the bass response, thus making their voice become clearer and brighter.

5. It is recommended to keep the grille and sponge windscreen clean to avoid any substance blocking the

proximity eect of the microphone.

Bodypack Controls and Indicators

1. Audio Input Connector: TA4F mini 4-pin connector accepts any PRO COMM lavalier, instrument and

headset microphones and cables. (See 5 ways of connection on AF Input Connections)

2. AF Button: Light stands for audio signal. Press it and the light goes out.

3. Antenna: Flexible 1/ 4 wave transmitting antenna.

4. Transmitter Housing: Holds PCB board and wires.

5. Battery Level Panel: Display battery status.

6. CCS IR Port: Align and syncs the transmitter and receiver frequency automatically.

7. Power Button: Press and hold 2 seconds to power ON or OFF.

8. Battery Circuitry Protection Reset Button

9. Battery Compartment: Accommodates one 18500 rechargeable battery.

10. Battery Cover: Hinged cover opens to provide access to one 18500 rechargeable battery.

11. Belt Clip: Detachable and reversible design allows the transmitter to be worn on a belt, waistband, or guitar

strap (Figure 1).

12. Battery Charging Contact: Align contacts during charging.

(a) Metal objects contact is forbidden.

(b) It is forbidden to contact metal objects.

(Figure 1)

(Positive Wear) (Opposite Wear)

Audio Input Operating Instructions

1. Insert the lavalier, headset microphone or instrument cable into the audio input connector before power

ON the transmitter.

2. Tighten the connector screw clockwise direction as shown in (Figure 2) for a secured t

(Figure 2)

Operating Instructions

1. Power On/O

a. Power On: Press the Power button to power ON. e battery status indicators and AF Button indicator

will light.

b. Power O: During Power On status, press and hold the Power button for 2 seconds to power OFF.

2. Battery Status Display

a. Red LED indicator is lit when battery is too low. Please recharge or insert a new recharged battery. e

transmitter will be shut down automatically if the battery keeps low status.

100% 75% 50% 25%

(green indicator)(red indicator)

3. AF Button Setup

a. Press AF Button to enter mute mode, and the indicator doesn’t light.

b. Press AF Button again to un-mute, and the indicator lights.

AF Input Connections

(1) 2-Wire Electret condenser

microphone Capsule

(2) 3-Wire Electret condenser microphone Capsule

(3) Dynamic Microphone

(4) Electric Guitar

(5) Line-in (Impedance 8KΩ ATT. 10dB

Battery Removal and Installation

1. Pushing down both snap locks on the sides to open battery compartment cover. Take out the one battery.

(Figure 3)

2. Insert one charged 18500 rechargeable battery into the battery compartment according to the

correct polarity (- and +) as shown in (Figure 4) . en close the battery compartment cover tightly.

(Figure 3) (Figure 4)

Caution

Remove the batteries if unused for a long period of time to prevent battery leakage, corrosion and causes possible

damage to electronics.

Caution

Note: Transmitter cannot be powered on with charged battery.

Method 1:

a. Ensure battery is inserted correctly with + top side.

b. If battery is inserted correctly it could be due to self battery protection mechanism. Insert the transmitter

Inhaltsverzeichnis

Andere Peavey Sender Handbücher

Peavey

Peavey VTS 1000 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung