Peco Peco TW205 Bedienungsanleitung

PECO®Wave Wireless® System

Operating Manual

RW205 Wireless

Receiver

TW205

Non-programmable

Wireless Thermostat

TW206 Programmable

Wireless Thermostat

Thank you for choosing the PECO®Wave Wireless®System.

The PECO Wave Wireless Systemis comprised of a wireless thermostat transmitter and a

receiver. PECO offers two wireless thermostats: the non-programmable TW205 Thermostat,

and the programmable TW206 Thermostat. Both operate with the same wireless RW205

Receiver. This operating manual contains important information on operating the TW205 and

TW206 Thermostats and on the RW205 Receiver.

The TW205/TW206 are designed for use primarily in 2- or 4-Pipe Fan Coil Units, PTAC,

PTHP, and heat pump applications. The TW205/TW206 support 1-HEAT/1-COOL, 1-HEAT/

2-COOL, 2-HEAT/1-COOL, and three fan speeds. The TW205/TW206 may be powered by

batteries, 24 VAC, or both (recommended). The TW206 can be conﬁgured for 7-day individual,

5/2-day, 5/1/1-day, or 7-day identical programmable operation, with four time periods per day.

The TW205/TW206 feature an attractive blue digital display and support auto changeover,

remote temperature probes, outdoor air damper/reversing valves, wireless occupancy sensors

(SW205), and door switches (SW206).

The RW205 Receiver is wired to the HVAC equipment and controls all outputs.

HE PE

WAVE WIRELE

TEM

Product Speciﬁcations

Temperature Range: 50° to 90° F (10° to 32° C)

Differential: 1° F (0.5°C)

Input Power: TW205-TW206 Thermostat: Two AA alkaline batteries or 24 VAC,

50/60 Hz; RW205 Receiver: 24 VAC, 50/60 Hz or 100-277 VAC, 50/60 Hz

Output Rating: RW205 output rating 24VA (Pilot Duty)

Wireless Type: 902 to 928 MHz Band, Frequency Hopping Spread Spectrum (FHSS)

Wireless Range: 100 feet (30.48 meters) typical reliable range in open air

Operation Temperature: 0° to 120° F (-17° to 48°C)

Shipping Temperature: -20° to 130°F (-28°to 54°C)

Operating Humidity: 5% to 95% RH, non-condensing

Physical Dimensions: TW205-TW206: 4.5”H x 5.75” W x 1.1”D

RW205: 4.8”H x 3.8”W x 1.3”D

Read and save this operating manual.

TABLE OF CONTENTS

The PECO Wave Wireless System......................................................................................................2

Front panel display reference: TW205 Thermostat..............................................................................6

Front panel display reference: TW206 Thermostat..............................................................................7

Button operation ..................................................................................................................................8

The TW205 & TW206 displays ..........................................................................................................12

Set the time and day (TW206 only) ...................................................................................................16

Select the Fahrenheit or Celsius temperature ...................................................................................17

Programming the TW206...................................................................................................................18

Custom program (TW206 only) .........................................................................................................19

Custom program: Copy feature (TW206 only)...................................................................................22

Overriding the program (TW206 only) ...............................................................................................23

FCC COMPLIANCE...................................................................................................................................24

!CAUTION!

•READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO OPERATE THIS THERMOSTAT AND

RECEIVER.

• Contact a qualiﬁed service person if at any time your system does not operate properly.

• Use care to avoid static discharge to the thermostat and receiver.

• Failure to observe safety information and comply with instructions could result in PERSONAL INJURY,

DEATH AND/OR PROPERTY DAMAGE.

• To avoid electrical shock or damage to equipment, disconnect power before installing or servicing and use

only wiring with insulation rated for full thermostat operating voltage.

• To avoid potential ﬁre and/or explosion, do not use in potentially ﬂammable or explosive atmospheres.

• This product, when installed, will be part of an engineered system whose speciﬁcations and performance

characteristics are not designed or controlled by PECO. You must review your application and national

and local codes to assure that your installation will be functional and safe.

• Retain these instructions for future reference.

IMPORTANT NOTE: This thermostat was shipped with factory default settings. Your thermostat’s installer

may have conﬁgured the thermostat differently from the factory default settings, and may have modiﬁed

or disabled certain features. Contact the installer or a service technician if you have questions about the

thermostat’s conﬁguration.

The illustration below depicts the non-programmable TW205 Thermostat display and

buttons.

FRONT PANEL DISPLAY REFERENCE: TW205 THERMOSTAT

SYSTEM button

Display

FAN button

°F /°C button

UP ▲and

DOWN ▼

buttons

AUTOMATION AND CONTROLS

The illustration below depicts the programmable TW206 Thermostat display and buttons.

FRONT PANEL DISPLAY REFERENCE: TW206 THERMOSTAT

SYSTEM button

Display

FAN button

UP ▲and

DOWN ▼

buttons

PROGRAM

button

AUTOMATION AND CONTROLS

System Button

The SYS (system) button is used to control the operating mode of the TW205/TW206.

Press the SYS button once to show the menu options, as described below. Continue

pressing SYS button to scroll through menu options. As you scroll, the menu option

being accessed (operating mode) will ﬂash. To select that option, allow the display to

automatically time out. The TW205/TW206 saves the “ﬂashing” option and switches the

thermostat to the selected operating mode. The SYS modes are:

HEAT – Indicates the system is in heating mode.

COOL – Indicates the system is in cooling mode.

AUTO – Indicates the system will automatically changeover between heating

and cooling modes as the room temperature varies.

OFF – Disables thermostat outputs.

SETBACK –Indicates the heating or cooling system is operating in manual setback

mode. (To appear, SETBACK must be selected in “Advanced Conﬁguration.” See the

“PECO Wave Wireless System TW205/TW206 &RW205 Installation Guide”).

NOTE: SETBACK must be selected in the Service Menu in order to appear in

the SYS mode (see “Advanced Conﬁguration” in the “Wave Wireless System

TW205-TW206 & RW205 Thermostat and Receiver Installation Instructions”). The

SYS button is also used to scroll through the Service Menu in advanced conﬁguration.

BUTTON OPERATION

Fan Button

The FAN button is used to control the fan mode. Pressing FAN will show fan mode options.

Press FAN continuously to scroll through the options. The “ﬂashing” option is automatically

saved and the thermostat times out. The modes are:

FAN – “FAN” will always be lit in conjunction with “ON” or “AUTO.”

ON – Turns on continuous fan, even if no demand exists for heating or cooling.

AUTO – Sets fan cycles with demand for heating and cooling.

*ON Hi – High speed fan is on continuously, even if no demand exists for heating or

cooling.

*ON M – Medium speed fan is on continuously, even if no demand exists for heating or

cooling.

*ON Lo – Low speed fan is on continuously, even if no demand exists for heating or

cooling.

*AUTO Hi – High speed fan cycles with active demand for heating and cooling.

*AUTO M – Medium speed fan cycles with active demand for heating and cooling.

*AUTO Lo – Low speed fan cycles with active demand for heating and cooling.

*NOTE: Options must be selected in the Service Menu in order to appear (see

“Advanced Conﬁguration” in the “Wave Wireless System TW205-TW206 & RW205

Thermostat and Receiver Installation Instructions”).

BUTTON OPERATION

Program Button (TW206 only)

The PROG (program) button is used to program the TW206. Press PROG button once

to show the ﬁve program mode options, described below. Press ▲or ▼buttons to scroll

through the options. As you scroll, the option being accessed will ﬂash. To select the

ﬂashing option (e.g.,”CLOCK”), press PROG again, and an associated submenu appears.

Press ▲or ▼to scroll through the submenu options. Press the PROG button to select an

option. The thermostat times out and automatically saves the “ﬂashing” option. The ﬁve

program mode options are:

CLOCK – Sets the current time and day (see “Setting the time and day”).

°F / °C – Sets temperature display to Fahrenheit or Celsius. Default setting is

Fahrenheit (see “Selecting the Fahrenheit or Celsius temperature”).

SET – Initiates the time and temperature schedule for a particular day or group of days.

Allows you to reset the thermostat to the factory program default settings

(see “Programming the TW206”).

COPY – Copies one day’s schedule to another day or to another group of days (see

“Programming the TW206”).

HOLD – Puts the thermostat in Temporary or Permanent Hold mode. Overrides your

programmed settings but does not lose them (see “Overriding the program”).

NOTE: Press the SYS button to exit the program menu at any time.

BUTTON OPERATION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Peco Thermostat Handbücher

Peco

Peco Performance pro T4000 series Bedienungsanleitung

Peco

Peco T8000 series Bedienungsanleitung

Peco

Peco Peco TW206 Bedienungsanleitung

Peco

Peco Perfomance Pro School T4900 Bedienungsanleitung

Peco

Peco TA155-046 Installationsanleitung

Peco

Peco TA180 Bedienungsanleitung

Peco

Peco Performance pro T4000 series Bedienungsanleitung

Peco

Peco Performance Pro T4900 School Bedienungsanleitung

Peco

Peco TA170-001 Installationsanleitung

Peco

Peco T170 Benutzerhandbuch

Peco

Peco Peco RW205 Bedienungsanleitung

Peco

Peco TB158 Bedienungsanleitung

Peco

Peco TA167-006 Bedienungsanleitung

Peco

Peco T4500 Bedienungsanleitung

Peco

Peco TF115P-003 Bedienungsanleitung

Peco

Peco Performance Pro T12000 Series Bedienungsanleitung

Peco

Peco WavePRO T2500 Bedienungsanleitung

Peco

Peco T190 Bedienungsanleitung

Peco

Peco TC170 Bedienungsanleitung

Peco

Peco T8000 series Bedienungsanleitung

Peco

Peco T158 Bedienungsanleitung

Peco

Peco TW180 Bedienungsanleitung

Peco

Peco TF115P-002 Bedienungsanleitung

Peco

Peco TA158-100 Installationsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung