Pedego CITY COMMUTER & INTERCEPTOR Kurzanleitung
PEDEGO ELECTRIC BIKES
CITY COMMUTER & INTERCEPTOR
ASSEMBLY INSTRUCTIONS AND OWNERS MANUAL
Pg. 2 Pg. 3
Carton Contents 2
Assembly Instructions 4
Safety 8
Operating Procedures 9
Charger 10
To Recharge the Battery 10
Battery and Charger Care 11
Fuse 11
Pedal Assist Mode 12
Meter Programming 13
Hand Throttle Control 14
Lights 14
Gears 15
Brakes 16
Appearance Care 17
Warranty 18
Commonly Asked Questions 20
Warning 21
Your Bike Information / Serial Number 23
Carton Contents
Pedego Bike
Pedals (2)
Owner’s Manual/Assembly Instructions
Lithium Ion Battery
Keys for Battery
Tool Kit
Battery Charger
Table of Contents
Pg. 2 Pg. 3
Pedego Electric Bikes
Welcome to the POG
First of all, we would like to thank you for choosing the Pedego electric bike.
We believe this technology, with the benets of electric propulsion,
provides you with the perfect vehicle to increase your personal mobility.
Our geared, brushless, electric hub motor allows you to run errands
or commute to work while saving money on gas and reducing your
environmental impact on our world. It also gives you the opportunity
to pedal if you want to get exercise along the way.
All this and it is just plain fun to ride!
If you have any concerns, questions or suggestions about the Pedego electric
Pedego!
PLEASE NOTE:
This manual is not intended as a detailed user, service, repair or maintenance manual.
Please seek assistance from a qualied technician for service, repairs or maintenance.
Pg. 4 Pg. 5
5. Insert the handlebar stem into the head tube on the bicycle. You may adjust
the height of the handlebars by moving the stem up or down to your comfort
level. Make sure the handlebars are aligned with the front wheel before tight-
ening and that the stem is not set above the maximum height indicator. Place
your thumb on the black locking mechanism on top of the stem, push down
and lift the lever up exposing the adjustment screws.
Assembly Instructions
Your bike has been pre-assembled and requires only a few simple steps to
get it ready for you to ride:
1. Remove the outside carton after cutting the nylon bands by lifting off the
entire box from the tray at the bottom.
2. Remove all the inside cardboard protection and bubble wrap.
3. Please locate and set aside the kit box containing the battery charger and
tool kit.
4. Carefully remove your bike from the bottom tray and gently rest it in place
with the kickstand down.
If the disc brakes are rubbing after installation, refer to Customer Help on our
website at www.pedegoelectricbikes.com/faqs/customerhelp/
For City Commuter
Pg. 4 Pg. 5
Figure 1. Figure 2.
3
3
Figure 3. Figure 4.
Move the stem so that you can see directly down the hole (Figure 1). Insert
the 6 mm allen wrench, supplied in the kit, into the hole and tighten the screw
clockwise until the handlebars do not move separately from the front wheel
(Figure 3).
In order to get the bolt securely tighten you may need to use a pair of plyers for
leverage (Figure 4).
Position the handlebars to your comfort level and lock handlebars into place
by pushing the handle back down. If handlebars move up or down after
pushing handle down, you can tighten the screw indicated in gure 2 with a
5 mm allen wrench in your kit.
Pg. 6 Pg. 7
5. The handlebars must be adjusted for height and align-
ment. First, remove the rubber protective cap and insert
the handlebar stem into the frame of the bicycle. With the
allen wrench provided in the tool kit, tighten the screw on
top of the stem underneath the rubber protective cap to
secure the handlebars in place. Make sure the handle-
bars are aligned with the front wheel before tightening
and that the stem is not set above the maximum height
indicator.
If need be, the angle of the handlebars may be positioned to your personal prefer-
ence. Loosen the front 2 bolts on the front stem plate and angle the handlebars
to your liking, then securely tighten the 2 bolts on the front stem plate. Make sure
that, when tightening, there is even spacing between the top and bottom bolts to
ensure maximum stability.
For Interceptor
Pg. 6 Pg. 7
6. Make sure the seat is tight enough so
that you can’t twist it out of alignment. Pull
the seat clamp handle away from the seat
post and slide the seat up or down to adjust
it. Move the clamp handle inward toward
the seat post so it is held tight by the clamp.
If necessary, tighten the clamp by twisting
the clamp handle clockwise while in the un-
clamped position. Then, fold the handle in
toward the seat post. This should require a
fair amount of force to ensure the seat post
is held tight. If necessary, the clamp can be
further tightened with an allen key when in
the clamped position. Make sure the seat
is not set with the vertical maximum height
marks above the clamp.
7. PLEASE NOTE – The pedals are marked
“L” for Left and “R” for Right. Using the
wrench provided in the tool kit, attach and
tighten the pedals. The left pedal is at-
tached by turning it counterclockwise and
the right pedal is tightened by turning it
clockwise.
3
Pg. 8 Pg. 9
Helmet:
Always wear an approved helmet while riding your Pedego and follow the helmet
manufacturer’s instructions for t, use and care of your helmet. It is your respon-
sibility to familiarize yourself with the laws of where you ride your Pedego and to
comply with all applicable laws.
Mechanical Safety Check:
Check the condition of your Pedego before every ride. Make sure no nuts, bolts
or xings are loose, with particular attention to the axle nuts and handlebar stem.
Make sure the tires are correctly inated with 30 psi minimum to 65 psi maximum
air pressure. Check the brakes for proper operation.
You must take your bike in to be serviced and checked by a qualied bike me-
chanic before 100 miles of riding. This is a standard good practice for any new
bike as cables will stretch and components will ‘bed in’. The service must include
spoke tensioning for both front and rear wheels.
Your First Ride:
When you buckle on your helmet and go for your rst ride, be sure to pick an
area away from cars, other cyclists, obstacles or other hazards in order to be-
come familiar with the controls, features and performance of your new Pedego.
Additional Passengers:
The Pedego bikes are designed for one passenger only. DO NOT carry any
additional passengers on the front or rear of the bike. The rear carrier is not de-
signed to carry the weight of any additional passengers, including baby carriers.
Safety
Pg. 8 Pg. 9
To be able to use the electric motor, the battery must be mounted by sliding the
fully charged battery forward into the battery holder.
The key locks the battery to the bike when the key is turned counterclockwise to
the locked position. The battery must be locked when riding or it may fall out. The
key does not have to be in to operate the bike.
The on/off switch is located on the bottom of battery. After inserting and locking
the battery into place, turn the battery on by ipping the switch to the “|” position.
Be sure to turn off the power when the Pedego is not in use or is recharging by
turning the battery on/off switch off.
You can ride it like a normal bike by leaving the switch in the off position.
3
On Off
Battery
Operating Procedures
Locked Open
Pg. 10 Pg. 11
Charging plug for 48 volt battery
City Commuter, Interceptor &Comfort
Cruiser
Charging plug for 36 volt battery
City Commuter & Comfort Cruisers
Included with your new Pedego is a lithium
ion battery, along with a charger, which
plugs into a standard 110 volt household
electric receptacle
A lithium ion battery requires specially de-
signed chargers. You should never charge
your battery with a substitute charger that
is not designed for this use. Use of an
unsuitable charger to charge a lithium ion
battery could result in over-heating, re or
even explosion.
The Pedego battery may be charged while
on the bike or removed and charged at a
location away from the Pedego in a dry
location. The battery is easily removed by
turning the key switch to the open position,
grasping the rear of the battery, and sliding
the battery to the rear of the Pedego.
To charge the battery, plug the charger
into an AC outlet. The LED indication light
should be green showing the charger is
working normally. Then plug the char-
ger into the charging port located on the
bottom of the battery by sliding open the
charger cover (Figure 6) and inserting the
plug.
Recharge the Battery
Figure 5.
Figure 6.
Battery and Charger
Inhaltsverzeichnis
Andere Pedego Fahrrad Handbücher
