peerless-AV HT642-003 Leitfaden
Max Load Capacity: 100 lb (45.4 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 07-07-11 SHEET #: 125-9221-1
Installation and Assembly:
Flat \ Tilt Wall Mount for VESA 400x400
Model: HT642-003
2 of 8 ISSUED: 07-07-11 SHEET #: 125-9221-1
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• stud nder ("edge to edge" stud nder is recommended)
• phillips screwdriver
• drill with 1/4" and 5/32" drill bits
• 5/16" socket wrench
Table of Contents
Parts List.................................................................................................................................................................................3
Attaching Adapter Bracket to Screen......................................................................................................................................4
Installation to Wood Stud Wall................................................................................................................................................4
Installation to Solid Concrete and Cinder Block Wall .............................................................................................................5
Installation to Metal Stud ........................................................................................................................................................6
Attaching Mounting Bracket Using Hook On Option...............................................................................................................8
Attaching Mounting Bracket Using Tilt Option ........................................................................................................................9
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer service at 1-800-729-0307.
• This product should only be installed by a qualied professional.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
• Never exceed the Maximum Load Capacity of 100 lb (45.4 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud nder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product was designed and intended to be mounted to the following supporting surfaces checked below with
the hardware included in this product as specied in the installation sheet. To mount this product to an alternative
supporting surface, contact Peerless customer care at 1-800-865-2112.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x Wood Stud None
x Wood Beam None
x Solid Concrete None
x Cinder Block None
x Metal Stud None
Brick Contact Customer Service
Other or unsure? Contact Customer Service
WARNING
SUPERSEDING COPY 200-9194revA 03-28-01/ m.b.
3 of 8 ISSUED: 07-07-11 SHEET #: 125-9221-1
Some parts may appear slightly different than illustrated.
Before you start make sure all parts listed are included with your product.
F
A
C
B
E
GH I J
D
Description Qty. Part #
Awall plate 1 201-1601
Badapter bracket 1 201-1931
C1/4 x 2.5 round phillips screw 4 520-9521
DM5 x 12 mm socket pin serrated washer head screw 6 510-1064
E#14 x 2.5 wood screw 6 5S1-015-C03
F4 mm security allen wrench 1 560-1129
GM8 x 16 mm phillips pan screw 4 520-2051
Htoggler 4 560-9708
Iwasher 4 540-1008
JAlligator® concrete anchor 6 590-0097
PARTS LIST
4 of 8 ISSUED: 07-07-11 SHEET #: 125-9221-1
Use a stud nder to locate center of studs.
For mounting to 16" centers
Using mounting bracket (A) as a template, drill four 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64
mm). Attach mounting bracket (A) to centers of wood studs using four #14 x 2.5" wood screws (E) and four
washers (I) as shown below.
Attach adapter bracket (B) to back of plasma screen using four M8 x 16 mm phillips screws (G).
• Do not overtighten. Overtightening may cause per-
manent damage to the screen. Torque to 26-35 in • lb
(30-40 kg • cm).
WARNING
1
2
A
E
I
Installation to Wood Stud Walls
Attaching Adapter Bracket to Screen
B
Screen
400 mm
400 mm
SUPERSEDING COPY 200-9194revA 03-28-01/ m.b.
5 of 8 ISSUED: 07-07-11 SHEET #: 125-9221-1
Position adapter bracket (A) at desired position on wall.
Use mounting bracket, making sure that it is level, as a
template to mark holes. Drill six 1/4" (6 mm) dia. holes
to a minimum depth of 2-1/2" (64 mm). Concrete must
be 2000 psi density minimum. Insert anchors (J) in holes
ush with wall as shown in gure 5.3. Place wall mount
assembly over anchors and secure with #14 x 2-1/2"
(6 mm x 65 mm) wood screws (E) and washers (I) as
shown in gure 3.4. Make sure wall plate is level and
tighten all fasteners.
Installation to Solid Concrete and Cinder Block Wall
3
• Tighten wood screws rmly, but do not overtighten.
Overtightening can damage the screws, greatly re-
ducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
WARNING
I
A
g3.4
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
or other nishing material as shown below. If mount-
ing to concrete wall covered with plaster/drywall is
unavoidable, plaster/drywall (up to 5/8" thick) must
be counter bored as shown below. Be sure concrete
anchors do not pull away from concrete when tight-
ening screws. If plaster/drywall is thicker than
5/8", custom fasteners must be supplied by installer.
WARNING
CINDER BLOCK
SOLID CONCRETE
E
J
1
3
2
J
Drill holes and insert anchors (J).
Place plate (A) over anchors (J) and secure with screws (E) with
washers (I).
Tighten all fasteners.
A
J
E
concrete
surface
CUTAWAY VIEW
INCORRECT CORRECT
wall plate
wall plate concrete
plaster/
dry wall
concrete
plaster/
dry wall
I
6 of 8 ISSUED: 07-07-11 SHEET #: 125-9221-1
Using a stud nder, locate and mark the edges of the metal stud used in mounting this product. Use of an edge
to edge stud nder is highly recommended. Use a level to draw a level, vertical line down the center of the stud.
Level wall plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud
center line. Drill four 1/2" holes through drywall and metal studs. Note: It may be necessary to drill 5/32" pilot holes
prior to drilling 1/2" holes.
3
• Product must be mounted through drywall that has a minimum thickness of 1/2" and into metal studs, 26 gauge or
heavier.
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
• Make sure that togglers are anchored into the center of the stud. The use of an "edge to edge" stud nder is highly
recommended.
WARNING
Installation to Metal Stud
3-1
3-2
3-3
3-4
3-5
Rotate toggler (H) clockwise to wedge it
against inside walls of metal stud.
Push into hole.
Pivot end of toggler (H).
Slide plastic cap forward while pulling back
rmly on ring.
Break off excess.
H
1
2
3
4
5
g.1.3
drill
1/2"
hole
H
H
H
H
SUPERSEDING COPY 200-9194revA 03-28-01/ m.b.
7 of 8 ISSUED: 07-07-11 SHEET #: 125-9221-1
Attaching Mounting Bracket Using Hook On Option
Attach four M5 x 12 mm serrated washer head
socket pin screws (D) to the holes on the sides of
mounting bracket (A) using the 4mm security allen
wrench (F)provided.
7-1 Position slots of adapter brackets (B) onto the
four M5 x 12 mm serrated washer head socket pin
screws (D) attached to mounting bracket (A).
D
B
SLOT
D
To secure adapter brackets (B) to mounting bracket (A), attach two M5 x 12 mm serrated washer head socket pin
screws (D) into the threaded inserts of adapter brackets (B), and through the slots on the sides of mounting bracket
(A). Tighten with the 4 mm security allen wrench (F).
For tilt option skip to Step 8
A
D
A
7-2
D
BD
A
7
SLOT
8 of 8 ISSUED: 07-07-11 SHEET #: 125-9221-1
© 2010 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
8Remove top two M5 x 12 mm socket pin serrated washer head screws (D) attached to wall plate (A). Loosen two
M5 x 12 mm socket pin serrated washer head screws (D) in slot as shown in Detail 1. Once desired tilt is
established tighten two M5 x 12 mm socket pin serrated washer head screws (D) in slots.
Mounting Bracket Using Tilt Option
D
BD
A
Detail 1
D
SLOT
D
Inhaltsverzeichnis
Andere peerless-AV Rack & Stand Handbücher
peerless-AV
peerless-AV ACC-MS46 Leitfaden
peerless-AV
peerless-AV SMARTMOUNT XT STX650 Bedienungsanleitung
peerless-AV
peerless-AV EWL-OH75F Bedienungsanleitung
peerless-AV
peerless-AV PRGS-UNV Bedienungsanleitung
peerless-AV
peerless-AV LCW620AD Leitfaden
peerless-AV
peerless-AV SR598-HUB Bedienungsanleitung
peerless-AV
peerless-AV DS-LEDIER-5X5 Bedienungsanleitung
peerless-AV
peerless-AV SMARTMOUNT Series Gebrauchsanweisung
peerless-AV
peerless-AV SR555E Bedienungsanleitung
peerless-AV
peerless-AV DS-S555-4X2 Bedienungsanleitung
peerless-AV
peerless-AV SmartMount SF632 Bedienungsanleitung
peerless-AV
peerless-AV DS-S555-3X2 Bedienungsanleitung
peerless-AV
peerless-AV DS-LEDLSCB Series Bedienungsanleitung
peerless-AV
peerless-AV LCC 18-C Leitfaden
peerless-AV
peerless-AV RMI3-FLIP2 Bedienungsanleitung
peerless-AV
peerless-AV SF660 Bedienungsanleitung
peerless-AV
peerless-AV SMARTMOUNT XT SFX645P Bedienungsanleitung
peerless-AV
peerless-AV MOD-AWM2 Bedienungsanleitung
peerless-AV
peerless-AV ESF686 Bedienungsanleitung
peerless-AV
peerless-AV DSF265P Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
