Peerless-AV PLAV 70-UNL Leitfaden

Models: PLAV 70-UNL, PLAV 70-UNL-S

PLAV 70-UNLP, PLAV 70-UNLP-S

Installation and Assembly - Universal Articulating

Swivel Double-Arm for 42" - 60" Plasma Screens

This product is UL Listed. It must be

installed by a qualified professional

installer.

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

Maximum UL Load Capacity: 200 lb (91kg)

2 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

Tools Needed for Assembly

•studfinder("edgetoedge"studfinderisrecommended)

•drill

•7/32" drill bit for wood studs

•5/16" masonry drill bit for concrete

•7/16"socketwrenchwithextension(recommended)

•level

•phillipsscrewdriver

•3/4"open-endwrench

Accessories

•External Wall Plate (WSP716, WSP716-S, WSP724,

WSP724-S)(MetalStud not evaluatedbyUL)

• Donotbegintoinstall your Peerless product until you have read and understood the instructions and warnings

containedinthisInstallationSheet. If you have any questions regarding any of the instructions or warnings,please

callPeerless customer care at1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-

wareand components.

• Neverexceedthe Maximum ULLoad Capacity. See pageone.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgetoedge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrewsfirmly, butdonot overtighten. Overtightening can damagetheitems, greatly reducing their holding

power.

• Thisproductwas designed and intended to bemountedtothe following supporting surfaces checked belowwiththe

hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-

ingsurface,contactPeerlesscustomer care at 1-800-865-2112.

• This product was designed to be installed on the following wall construction only;

WALLCONSTRUCTION ADDITIONALHARDWAREREQUIRED

xWoodStud None

xWoodBeam None

xSolidConcrete None

xCinderBlock None

MetalStud Do not attach except with Peerless accessory kit for metal studs;

Contact Customer Service for Peerless accessory kit for metal studs.

Brick ContactCustomer Service

Otheror unsure? ContactCustomerService

WARNING

NOTE: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List..............................................................................................................................................................................3

Installation to Double Wood Stud Wall..................................................................................................................................6

Installation to Solid Concrete or Cinder Block .......................................................................................................................7

3 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

PLAV70-UNL PLAV70-UNL-S

PLAV70-UNLP PLAV70-UNLP-S

DESCRIPTION QTY. PART# PART#

Awallplate 1 201-1040 201-4040

Btilt-roll assembly 1 201-1042 201-4042

Carmassembly 1 201-1044 201-4044

Dwallsupportarm axle 2 201-1041 201-1041

Evinyltrim 3 600-1012 600-1012

FM10 x 1.5 x 15 mm screw bolt 8 520-9262 520-9262

G.505 x .75 x .062" nylon washer 1 540-1074 540-1074

Htilt adjustment knob 1 560-0108 560-0108

Icarriage bolt 3/8"-16 x 3.25" 1 520-1315 520-1315

J1.525 x 2 x .062" delrin washer 4 540-1070 540-1070

K#8-32 x .375" socket head cap screw 2 520-1210 520-1210

Lplastic finishing cap 6 590-1123 590-1123

Mholdingpin 2 580-1166 580-1166

Nretainerplug 2 590-1007 590-1007

O5/16 x 3" wood screw 8 520-1243 520-1243

P.250 x 1 x .068" washer 8 540-1063 540-1063

Q9/64"allenwrench 1 560-9728 560-9728

Rcablemanagementclips 8 590-1166 590-1166

Scable tie 8 590-1168 590-1168

T36"polyestermeshsleeve 2 600-1015 600-1015

U6mmallen wrench 1 560-9716 560-9716

Wanchor 8 590-1025 590-1025

Before you start make sure all parts

listed are included with your product.

Wall Mount Parts List

Some parts may appear slightly different than illustrated.

R S

4 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

CCBBAA

Before you begin, make sure all parts shown are included with your product.

PLAV 70-UN

PLAV 70-UNL-S PLAV 70-UNL

PLAV 70-UNLP-

Description Qt

Part

adapter bracket 1 201-1110 201-4110 201-1110 201-4110

BB shallow adapter bracket 2 201-1511 201-4511 201-1514 201-4514

CC deep adapter bracket 2 201-1510 201-4510 201-1513 201-4513

DD allen wrench 1 560-9646 560-9646 560-0072 560-0072

Adapter Bracket Parts List

5 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

M5 x 25 mm (4)

520-1122

M4 x 12 mm (6)

510-1079

M4 x 25 mm (4)

510-1082

M5 x 12 mm (4)

520-1064 M6 x 12 mm (4)

520-1050

M6 x 25 mm (4)

520-1211 multi-washer (6)

580-1036

SecurityAdapter Bracket Fasteners

M6 x 20 mm (4)

520-9554

M6 x 30 mm (4)

520-1067

M8 x 15 mm (6)

520-1068

M8 x 40 mm (4)

520-1152

M8 x 25 mm (4)

520-1101

M6 x 20 mm (4)

520-9402

M6 x 30 mm (4)

510-9109 multi-washer(6)

580-1036

M8 x 16 mm (6)

520-9257

M8 x 40 mm (4)

520-1136

M4 x 12 mm (6)

504-9013

Phillips Adapter Bracket Fasteners

M4 x 25 mm (4)

504-1015

M5 x 12 mm (4)

520-1027 M5 x 25 mm (4)

520-9543

M6 x 12 mm (4)

520-1128

M6 x 25 mm (4)

520-1208 M8 x 25 mm (4)

520-1031

I.D. .22" (5.6 mm) (4)

540-1057 I.D. .34" (8.7 mm) (4)

540-1059

I.D. .22" (5.6 mm) (4)

540-1057 I.D. .34" (8.7 mm) (4)

540-1059

6 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

• Installermustverify that the supporting surface will safely support thecombinedloadof the equipment and all attached

hardwareandcomponents.

• Tightenwoodscrews so that wall plate is firmlyattached,butdo not overtighten. Overtightening can damage the

screws,greatly reducing their holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal

studs (contact customer care). Metal stud installation is not UL evaluated.

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovidedis for attachment of mountthroughstandard thickness drywall or plasterintowoodstuds. Installers

areresponsible to provide hardwareforother types ofmountingsituations.

• Neverexceedthe Maximum UL Load Capacity of 200 lb(91kg).

WARNING

Installation to Wood Stud Wall

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Useofanedge-to-edgestudfinder is highly recommended. Based on their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The top mounting slots should be located .43" below the

desired screen center. Level plate, and mark the center of the eight mounting holes. Make sure that the mounting

holes are on the stud centerlines. Drill eight 7/32" dia. holes 3" deep. Make sure that the wall plate is level, secure it

using eight 5/16 x 3" wood screws (O) and washers (P).

Skip to step 2 on page 8.

• Never mount this product to metal studs without the

requiredaccessory.

WARNING

7 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

IMPORTANT!Concretemustbe2000psidensity

minimum.

Use wall plate (A), making sure that it is level, as a

template to mark holes. The top mounting slots

should be located .43" below the desired screen

center. Use the masonry bit to drill 5/16" (8 mm) dia.

holes to a minimum depth of 3" (76 mm). Insert

anchors (W) in holes flush with wall as shown (right).

Placewall plate (A) overanchors(W) andsecurewith

5/16 x 3" wood screws (O) and washers (P).

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardwareandcomponents.

• Neverexceedthe Maximum UL Load Capacity of 200 lb(91kg).

WARNING

• Always attach concrete expansion anchors directly to

load-bearingconcrete.

• Neverattach concrete expansion anchorstoconcrete

coveredwith plaster, drywall,orother finishing mate-

rial.Ifmounting to concrete surfaces coveredwitha

finishingsurface is unavoidable,the finishing surface

mustbecounterbored as shown below. If plaster/

drywall is thicker than 5/8", custom fasteners must be

suppliedby installer (NotULevaluated).

WARNING

• Tighten wood screws so that wall plate is firmly

attached,but do notovertighten.Overtightening can

damagescrews, greatly reducingtheirholding power.

• Never tighten in excess of 80 in • lb (9 N.M.).

WARNING

Installation to Concrete Wall

1-4

1-1

1-3

1-2

concrete

surface

Drill hole(s) and insert anchor(s) (W)

mounting

plate

Place plate over anchor(s) (W) and secure with screw(s)(O)

Tighten all fasteners

CUTAWAYVIEW

INCORRECT CORRECT

mounting

plate

plaster/

drywall

concrete mounting

plate concrete

plaster/

drywall

8 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

• If you are uncertain that product is properly installed, call customer care.

WARNING

To route cables through cord management

channels:Slide one meshsleeve(T)over

each cable. Use cable ties (S) to tighten mesh

sleevesto cables.

Pullcordsthroughcordmanagementchan-

nels,leavingenoughslacktoallowfullrangeof

movementforswingarmassembly(C) as

showniffigure 3.1.

3-1

fig 3.1

To route cables using cable management clips:

Snapeightcable management clips(R)intoboth

swing arms(C)as shown in figure 3.2.Cable ties (S)

areusedwith clips for cord management.

Slideonemeshsleeve(T) over each cable. Use

cable ties (S) to tighten mesh sleeves to cables.

CORD

MANAGEMENT

CHANNEL C

3-1

Note: There are three mounting positions. The

center position is shown right. Arm assemblies

must be mounted with one mounting hole

separating them. Slidewashers(J)over wall

support arm axles (D). Next, insert plastic caps (N)

into axles. Then, insert holding pins (M) into axles.

See detail 1.

Note: Fit of axles (D) into wall plate (A) and arm

assembly (C) will be tight. Gently tap into place

with a hammer if necessary.

Insert socket cap screws (K) into hole at bottom of

wall support arm axles (D) as shown in detail 3.

Tightenscrewusing 9/64" allen wrench(Q).

Place arm assembly (C) with washers (J) into wall

plate (A). Insert axle assemblies shown in detail 1

throughwallplate (A), arm assembly (C),and

washers (J). Lock axles in place by aligning

holding pins (M) with notches shown in detail 2.

2-1

2-2

DETAIL 3

NOTCH

DETAIL 2

DETAIL 1

fig 3.2

9 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B).Attach tilt-roll assembly to adapter bracket (AA)

with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).

• Donot overtightenscrews! Overtighteningmayhinder

rolloption.

CAUTION

4Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm

assembly(C).

4-1 Insertonefinishingcap(L)intoeachunused hole of wall plate (A).

SWIVELBOX

10 of 14 ISSUED: 06-05-06 SHEET #: 202-9142-5 11-21-07

Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread.

.25" F

• Use an assistant or mechanical lifting equipment to safely lift and position the plasmaTV.

WARNING

• After tilt is adjusted, all fasteners must be tightened.

Failure to do so will result in damage to the mount.

CAUTION

SWIVELBOX

Hook tilt-roll assembly (B) onto M10 screws (F). Insert

carriage bolt (I) into slot of swivel box as shown in

figure 6.1. Install nylon washer (G)andtiltadjustment

knob(H).

Install remaining two M10 screws (F) as shown in

figure6.2. HAND TIGHTENallfour M10 screwsto

allowfor tilt adjustment. Removetapefrom carriage

bolt (I). For tilt adjustment, gently push back on the

top of plasma to relieve pressure on knob.Adjust tilt to

desired position and tighten tilt adjustment knob (H),

then securely tighten all four M10 screws (F) using

6mmallenwrench (U).

6-1

6-2

Adapter bracket not shown for clarity. Adapter bracket not shown for clarity.

SWIVELBOX fig 6.1 fig 6.2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere peerless-AV Rack & Stand Handbücher

peerless-AV

peerless-AV WMJ018 Bedienungsanleitung

peerless-AV

peerless-AV ACC166 Bedienungsanleitung

peerless-AV

peerless-AV SMARTMOUNT ST660 Bedienungsanleitung

peerless-AV

peerless-AV SR555M Bedienungsanleitung

peerless-AV

peerless-AV PWV240/BK Leitfaden

peerless-AV

peerless-AV HLG440-LG(-Q10) Bedienungsanleitung

peerless-AV

peerless-AV YBA4X4 Bedienungsanleitung

peerless-AV

peerless-AV SPL724 Bedienungsanleitung

peerless-AV

peerless-AV DS-LEDM Series Bedienungsanleitung

peerless-AV

peerless-AV PM 610 Leitfaden

peerless-AV

peerless-AV RMI2W Bedienungsanleitung

peerless-AV

peerless-AV STP680 Bedienungsanleitung

peerless-AV

peerless-AV Smart-Mount SP850-UNL Bedienungsanleitung

peerless-AV

peerless-AV SR560M Bedienungsanleitung

peerless-AV

peerless-AV DS-MBZ942L-2X1 Bedienungsanleitung

peerless-AV

peerless-AV KIP586-3LG-EUK Bedienungsanleitung

peerless-AV

peerless-AV SR598W Bedienungsanleitung

peerless-AV

peerless-AV MSA-301 Leitfaden

peerless-AV

peerless-AV IM760PU Bedienungsanleitung

peerless-AV

peerless-AV ACC002 Bedienungsanleitung

peerless-AV

peerless-AV DCS400 Bedienungsanleitung

peerless-AV

peerless-AV ACSBR1 Bedienungsanleitung

peerless-AV

peerless-AV DS-VW765-LQR Bedienungsanleitung

peerless-AV

peerless-AV ACSBR2 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung

peerless-AV PLAV 70-UNL Leitfaden

Beliebte Rack & Stand Handbücher anderer Marken