PEGAS Evolution Bedienungsanleitung

OPERATION MANUAL

www.beerinnovations.com

Evolution

OPERATION MANUAL

WWW.BEERINNOVATIONS.COM/Evolution_operation_manual

OPERATION MANUAL

www.beerinnovations.com

CONTENTS

1. PEGAS Evolution device diagram

2. Function of device

3. Technical data

4. Assembly and installation

5. Typical connection pattern

6. Changeover of the universal bottle holder mechanism

7. Dispensing procedure

8. Device maintenance

9. Troubleshooting

10. Safety measures

11. Additional information

12. Disassembling the ow switch

13. Assembling the ow switch

Pegas Evolution Device diagram for ordering spare parts

PEGAS EVOLUTION

1411

131210

1. PEGAS Evolution Device Diagram

2. Function of Device

The PEGAS Evolution device is intended for fast foam-free dispensing of foamy and/or car-

bonated beverages (including beer) from pressurized containers (kegs) into plastic bottles with

PCO 1810/1881 or BPF necks.

Dispensing is based on the backpressure method. This method ensures foam-free dispensing which

preserves beverage quality when storing sealed bottles for long periods. The use of new plastic bottles

is recommended for beverage dispensing.

PEGAS Evolution Device Diagram

1. Switch handle 2. Body 3. Plug 4. Throttle valve 5. Universal bottle holder 6. Screw 7. Nut

8. CO2supply nipple 9. Drain nipple 10. Shank

11. Flat washer 12. 5/8’’ nut 13. Coupling nut 14. Beverage supply nipple

OPERATION MANUAL

www.beerinnovations.com

4. Assembly and Installation

Remove all of the parts from their individual packaging.

* Estimated when lling a two-liter bottle at 60C or less.

** Per liter of product lled under 0.2 MPa of pressure.

3. Technical Data

1. Dispensing device – 1 pce.

2. Shank – 1 pce.

3. Throttle valve – 1 pce.

5. Nuts – 2 pcse. 6. Nipples with rings – 2 pcse.

7. Operation manual – 1 pce.

4. Plug – 1 pce.

Designation Unit Value

Filling capacity* l/hour

45-120

CO2pressure when supplied to a keg MPa

0,25-0,3

CO2 ow rate (to create backpressure)** g/l

0,25-0,3

Device weight Net kg

0,75

Gross kg

0,85

PEGAS EVOLUTION

Spare parts set:

Wrench S19

Wrench S24

Wrench S27

Hex wrench S12

The following tools are required for device assembly and installation:

№IDENTIFICATION PCS

1Ram APH.40.00.016 2

2 Gasket PMK.10.00.027 2

3 Ring 008-011-19 APH-5.00.00.804 1

4Ring 005-009-25-2-6 GOST 9833-73 1

5Ring 013-017-25-2-6 GOST 9833-73 2

6Mushroom Knob PG01.02.00.005 2

7 Rubber plug PG01.02.00.003 1

8 Ring PG01.02.02.002 2

9 T-connector PMK.10.00.044 1

10 Clamp d=13,3 6

Ring 005-008-19 APH-5.00.00.802

Ring 003-005-14-2-6 GOST 9833-73

Gasket PMK.10.00.026

10 11 12

8 9

54 6

2 3

OPERATION MANUAL

www.beerinnovations.com

4. PEGAS Evolution device should be assembled as follows:

Before installing the shank, make sure the

device has a gasket.

Using an S19 wrench, screw the shank into

the 5/8” threaded hole in the body.

Using an S12 hex wrench, screw the plug

into the 5/8” threaded hole or for dispens-

ing beer into glasses/mugs. (Tap not in-

cluded in contents of package)..

Install the throttle valve [4].

Make sure the device

is sealed

Make sure the device

is sealed

PEGAS EVOLUTION

Insert the CO2supply nipple and the drainage

nipple into the matching holes on the device.

Place the nuts on to the nipples and hand

tighten them up to the stop.

Unscrew the coupling nut [13] from the shank.

Remove the beverage supply nipple [14] to-

gether with its gasket. Unscrew the 5/8” nut [12]

and remove the at washer [11]. The device is

now ready for installation.

1410 11 1312

OPERATION MANUAL

www.beerinnovations.com

Insert the free end of the shank into the

matching hole.

Place the at washer on to the shank from

the inside; tighten the 5/8” nut using an

S27 wrench, secure the device in a vertical

position with the 5/8” nut.

Place the coupling nut on to the nipple and

tighten it with an S24 wrench. Ensure that

the gasket is properly placed in position.

Installation of the device into a 23+ mm through hole

PEGAS EVOLUTION

Connect the beverage supply hose to the bev-

erage supply nipple. Fix the hose with a pipe

clip (not included to the package).

Connect the CO2supply hose to the upper

nipple. Connect the drainage hose – to the

bottom nipple. Fix the hoses with pipe clips.

Andere Handbücher für Evolution

Inhaltsverzeichnis

Andere PEGAS Getränkespender Handbücher

PEGAS

PEGAS CRAFTAP 3 Referenzhandbuch

PEGAS

PEGAS BeerCase Bedienungsanleitung

Beliebte Getränkespender Handbücher anderer Marken

Ugolini

Ugolini MT micro Bedienungsanleitung

Bunn

Bunn SLCA-7 Montageanleitung

Gekkeikan

Gekkeikan Sake Machine Bedienungsanleitung

Olympia

Olympia DH709 Bedienungsanleitung

Marco

Marco ECOSMART PB10 Bedienungsanleitung

Marvel

Marvel ML24BN Series Handbuch

Cecilware

Cecilware 2K-GB-LD Handbuch

Sure Vend

Sure Vend 673 Bedienungsanleitung

Cornelius

Cornelius 2 Flavor Post-Mix Cold Coffee Dispenser Quest... Bedienungsanleitung

Nostalgia Electrics

Nostalgia Electrics KEG7000SS Bedienungsanleitung

Bunn

Bunn LCR-3 HV Fehlerbehebungshandbuch

Servend

Servend SV-200 Bedienungsanleitung

EdgeStar

EdgeStar VBR440 Bedienungsanleitung

Cornelius

Cornelius A.B.S. Unit Bedienungsanleitung

CDS AUTOMATEN

CDS AUTOMATEN ML-16C2-C Bedienungsanleitung

Siemens

Siemens GA 3000 Gebrauchsanweisung

Cornelius

Cornelius FCB V4 Technische Daten

Selbach

Selbach Fruit Juice dispenser Bedienungsanleitung