Pellenc FIXION 2 Bedienungsanleitung

TYING MACHINE

FIXION 2

Operating instructions 29_133084-G

02/2022

ENG

Translation of the original op-

erating instructions manual

READ THE USER GUIDE CAREFULLY BEFORE USE

TYING MACHINE FIXION 2

29_133084-G

TABLE OF CONTENTS

1. INTRODUCTION ..................................................................................................................... 5

2. SAFETY ................................................................................................................................... 6

2.1. INTENDED USAGE .......................................................................................................................... 6

2.2. GENERAL POWER TOOL SAFETY WARNINGS .......................................................................... 6

2.2.1. WORK AREA SAFETY ...................................................................................................................... 6

2.2.2. ELECTRICAL SAFETY ....................................................................................................................... 6

2.2.3. PERSONAL SAFETY ......................................................................................................................... 7

2.2.4. POWER TOOL USE AND CARE ........................................................................................................ 7

2.2.5. BATTERY TOOL USE AND CARE ..................................................................................................... 7

2.2.6. SERVICING ....................................................................................................................................... 8

2.2.7. MANAGEMENT OF THE RECYCLING AND RECOVERY OF WASTE FROM YOUR TOOL ................... 8

2.3. SAFETY WARNING THE TYING MACHINE ................................................................................... 8

2.4. SAFETY MEASURES ASSOCIATED WITH BATTERY USE ......................................................... 8

2.5. SAFETY MEASURES WHEN USING THE "PELLENC" CHARGER ............................................. 9

2.6. SAFETY SIGNAGE .......................................................................................................................... 9

2.7. PERSONAL PROTECTION EQUIPMENT ..................................................................................... 10

3. DESCRIPTION AND TECHNICAL CHARACTERISTICS .................................................... 11

3.1. DESCRIPTION OF THE TOOL ...................................................................................................... 11

3.2. TECHNICAL FEATURES ............................................................................................................... 12

4. COMMISSIONING ................................................................................................................. 13

4.1. FITTING THE HOLSTER TO THE BELT ...................................................................................... 13

4.2. FITTING THE LATERAL DISPENSER EQUIPPED WITH THE LARGE TIE BAND SPOOL ONTO

THE BELT. ............................................................................................................................................. 13

4.3. FITTING THE ADAPTABLE DISPENSER LOADED WITH THE SMALL TIE BAND SPOOL ONTO

THE TYING MACHINE. ......................................................................................................................... 15

5. USE ....................................................................................................................................... 16

5.1. TYING MACHINE ON/OFF ............................................................................................................ 16

5.2. ADJUSTING THE TIGHTNESS OF THE TIE ................................................................................ 16

5.3. RELOAD WITH THE LARGE TIE BAND SPOOL ........................................................................ 16

5.4. RELOAD THE SMALL TIE BAND SPOOL ................................................................................... 18

5.5. INSERT THE TIES INTO THE TYING MACHINE ......................................................................... 19

5.6. GRIP ............................................................................................................................................... 20

5.7. END OF THE TIE BAND SPOOL ................................................................................................. 22

5.8. CHARGING THE TOOL ................................................................................................................. 24

5.8.1. INSTRUCTIONS BEFORE CHARGING BUILT-IN BATTERY .............................................................. 24

5.8.2. THE DISPLAY SHOWING REMAINING BUILT-IN BATTERY CAPACITY ............................................ 24

5.8.3. CHARGING THE BUILT-IN BATTERY .............................................................................................. 24

6. MAINTENANCE .................................................................................................................... 28

TYING MACHINE FIXION 2

29_133084-G

6.1. MAINTENANCE TABLE ................................................................................................................ 28

6.2. SPARE PARTS ............................................................................................................................... 28

6.3. NETTOYAGE .................................................................................................................................. 28

6.4. REPLACEMENT OF THE UPPER GUIDE .................................................................................... 31

6.5. REPLACING THE SUPPORT ROLLER ........................................................................................ 32

6.6. REPLACING THE TWISTER ......................................................................................................... 34

6.7. BUILT-IN BATTERY ....................................................................................................................... 35

6.8. CHARGER ...................................................................................................................................... 35

7. INCIDENTS AND TROUBLESHOOTING ............................................................................. 37

7.1. SUMMARY OF CHARGE INDICATOR AND BEEP MESSAGES ................................................ 37

7.2. TYING MACHINE AND INTEGRATED BATTERY ....................................................................... 37

7.3. CHARGER ...................................................................................................................................... 38

8. STORAGE AND TRANSPORT ............................................................................................ 39

8.1. STORAGE ...................................................................................................................................... 39

9. ACCESSORIES AND CONSUMABLES .............................................................................. 39

9.1. ACCESSORIES INCLUDED .......................................................................................................... 39

9.2. OPTIONAL ACCESSORIES .......................................................................................................... 39

9.3. CONSUMABLES ............................................................................................................................ 40

9.3.1. TIES ................................................................................................................................................ 40

10. WARRANTIES .................................................................................................................... 41

10.1. GENERAL WARRANTIES ........................................................................................................... 41

10.1.1. STATUTORY WARRANTY ............................................................................................................. 41

10.1.2. COMMERCIAL WARRANTYPELLENC ............................................................................................ 41

10.1.3. PAID AFTER-SALES SERVICE ...................................................................................................... 42

11. EC STATEMENT OF COMPLIANCE ................................................................................. 44

11.1. "EC" DECLARATION OF CONFORMITY: FIXION 2 ................................................................. 44

TYING MACHINE FIXION 2

29_133084-G

1. INTRODUCTION

Dear Customer,

Thank you for purchasing your Tying machine FIXION 2 . Properly used and maintained, this equipment will give

you years of satisfaction.

Warning

In accordance with product liability laws, we are not responsible for damage caused by our

product if the product includes an accessory that is not from the manufacturer or is not approved

by the manufacturer. The use of any other accessory may increase the risk of injury.

Warning

Your machine contains numerous recoverable or recyclable materials. Return it to

your dealer or, failing this, to an approved servicing centre to be treated.

Comply with the regulations in force in your country as concerns environmental protection associated with your

activity.

Warning

It is imperative that you read through the ENTIRE user’s manual guide before using or servicing

the tool. Always comply with the instructions and illustrations provided in the user’s manual.

Throughout the user’s manual guide you will find advisory notes and information entitled: NOTE, IMPORTANT,

ATTENTION and WARNING.

Points marked “NOTE” indicate additional information.

Points marked "IMPORTANT" warn the user of a potential risk for the equipment.

Points marked “ATTENTION” warn the user of a potentially hazardous situations which if not avoided may result

in minor injuries.

Points marked “WARNING” warn the user of a potentially hazardous situation which if not avoided may result in

serious injury or death.

The warning indicates that damage resulting from failure to comply with the procedures and instructions is not

covered by the warranty and the owner will be liable for any repair costs.

Safety indications are also given on the tool; they remind you of the safety precautions to be taken. Identify and

read these indications before using the tool. Immediately replace any indications that may become partially illegible

or deteriorated.

Refer to Section 2.6, “Safety signage” for the location diagram of the safety stickers affixed to the tool.

No part of this manual may be reproduced without the written permission of the company PELLENC. The illustrations

provided in this manual are for information purposes only and are in no way contractual. The PELLENC company

reserves the right to make any modification or improvement to its products as deemed necessary without inform-

ing customers already in possession of a similar model. This manual forms an integral part of the tool and must

accompany the tool if it changes hands.

TYING MACHINE FIXION 2

29_133084-G

2. SAFETY

2.1. INTENDED USAGE

• The Tying machine FIXION 2 is a professional tool whose use is reserved exclusively for tying vine shoots.

• Any other use of this tool is not intended.

• The PELLENC company accepts no responsibility for any damage caused by improper or unspecified use different

from its original intention.

• The user is responsible for any accident resulting from improper use or unauthorized modification of this tool.

• The PELLENC company accepts no responsibility for any damage caused by the use of non-original parts or

accessories.

2.2. GENERAL POWER TOOL SAFETY WARNINGS

Warning

Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/

or serious injury.

Note

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cord-

less) power tool.

2.2.1. WORK AREA SAFETY

1. Keep the work area clean and well lit. Cluttered or dark areas invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,

gases or dust. Power tools create sparks, which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control of the tool.

2.2.2. ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed surfaces or grounded surfaces such as pipes, radiators, ranges, and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of

electric shock.

5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

6. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) pro-

tected supply. Use of an RCD reduces the risk of electric shock.

TYING MACHINE FIXION 2

29_133084-G

2.2.3. PERSONAL SAFETY

1. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use

a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal injury.

2. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal

injuries.

3. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the

switch or plugging in power tools with the switch in the on position can cause accidents.

4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in personal injury.

5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power

tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving

parts. Loose clothes, jewelry or long hair can be caught in moving parts.

7. If devices are provided for connection of dust extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool

safety principles. A careless action can cause severe injury within a fraction of a second.

2.2.4. POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will

do the job better and safer at the rate for which it was designed.

2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or remove the battery pack, if detachable, if from the

power tool before making any adjustment, changing accessories, or storing power tools. Such preven-

tive safety measures reduce the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained

users.

5. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely

to bind and are easier to control.

7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into

account the working conditions and the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

8. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasp-

ing surfaces do not allow for safe handling and control of the tool in unexpected situations.

2.2.5. BATTERY TOOL USE AND CARE

1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another battery pack.

2. Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

3. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns or a fire.

4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

TYING MACHINE FIXION 2

29_133084-G

5. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk of injury.

6. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130 °C (or 265°F) may cause explosion.

7. Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range may

damage the battery and increase the risk of fire.

2.2.6. SERVICING

1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

2. Never service damaged battery packs. Service of battery packs should only be performed by the manufac-

turer or authorized service providers.

2.2.7. MANAGEMENT OF THE RECYCLING AND RECOVERY OF WASTE FROM YOUR TOOL

1. When the tool reaches the end of its life, PELLENC keeps the end of life sheet of the equipment at

disposal. The end of life sheet provides instructions for safely removing components.

2.3. SAFETY WARNING THE TYING MACHINE

1. Never modify the connector in any way whatsoever.

2. Always switch off the battery when the machine is not in use (LED must be off).

3. Never use the tool if it is damaged, incorrectly set or incompletely assembled.

4. Never remove or disable a safety device. Have the safety device repaired if is faulty.

5. Do not disassemble the tying machine.

6. Please test the machine before use to check that it is working properly.

2.4. SAFETY MEASURES ASSOCIATED WITH BATTERY USE

1. If not using the battery unit, store it away from other metal objects such as paper clips, coins, keys, nails, screws

or other such small metal items that might form a connection between the two terminals. Creating a short-circuit

between the battery terminals can lead to burns or cause a fire.

2. Keep the battery out of the reach of children and place it on a non-combustible support.

3. Do not interfere with its cooling cycle.

4. Do not use or leave the battery near a heat source (> 60°C).

5. Do not leave the battery in direct, strong sunlight.

6. Do not expose the battery to microwaves or high pressure.

7. Do not immerse the battery in water.

8. The batteries must be charged in a dry, ventilated room at a temperature between 10°C and 25°C maximum,

away from any moisture.

9. If the battery is not used for 10 days, the battery will automatically discharge until it reaches its storage charge

rate, then goes to standby. It will heat up during this phase.

10. Over time, the capacity of your battery decreases. When it reaches half of its original battery-life operating

autonomy, it should be replaced.

11. The battery may lose 1 to 4 % of its capacity when exposed to a temperature higher than or equal to 55 °C

for one week.

12. The charging location must be equipped with a class D fire extinguisher (for metal fires) in good working order.

13. The standards in effect must be complied with when shipping a complete tool or a battery.

• Complete tool with battery: product classified UN3481 class 9.

• Battery alone: product that is classified as class 9, UN3480.

14. Use of a battery other than that provided by Pellenc SA is dangerous (risk of serious injury). If a different battery

is used, Pellenc SA cannot be held responsible for any consequences.

TYING MACHINE FIXION 2

29_133084-G

15. The battery must be protected from any impact and must be positioned and secured appropriately during trans-

portation.

16. In the case of suspicious smoke, place the battery outside the charging area or transportation vehicle as far

away as possible from any inflammable material.

17. Never store a battery when its capacity is below 50 %. Recharge the battery before storage if the value is

below 50%.

18. In inappropriate conditions, a liquid can flow batteries; avoid contact with it. In the event of accidental contact,

rinse with water. In the event of contact with eyes, seek professional medical help. The liquid leaking from the

batteries can cause irritations or burns.

19. Pellenc power tools must only be used with the battery units designed for the purpose. Use of other battery

units can present a risk of injury and fire.

20. Recharge only with the charger specified by the manufacturer. A charger adapted to one type of battery unit

may present a fire risk if used with a different battery unit.

21. Do not use the battery for any purpose other than that initially envisaged (exclusively for use with Pellenc tools).

22. At the end of its life, the battery must be returned to the authorized distributor from whom it was purchased to

be recycled in accordance with waste regulations.

23. Fragile case, contains an electronic board and lithium.

2.5. SAFETY MEASURES WHEN USING THE "PELLENC" CHARGER

1. When in operation, the charger’s temperature can reach 60°C. No flammable material must be within 1.5 metres

of the charger and battery.

2. Place the charger out of the reach of children and on a non-combustible support.

3. Do not interfere with its cooling cycle.

4. The charger is intended only for recharging the battery. Do not charge non-rechargeable batteries.

5. The charging location must be equipped with a class D fire extinguisher (for metal fires) in good working order.

6. If the output cord is cut or damaged, bring the entire charger back to the authorised distributor where the tool

was purchased.

7. Only recharge using the "PELLENC" charger indicated by the manufacturer. A charger adapted to one type of

battery unit may present a fire risk if used with a different battery unit.

8. This charger is designed to charge Pellenc tool lithium batteries.

9. Do not use it for any other purposes.

10. Children must be supervised to ensure they do not play with the charger.

11. Check that the cable cannot be bent and that it does not touch hot surfaces or sharp edges.

12. Ensure good ventilation during the charging.

13. Never cover the charger. This charger must not be used outdoors.

14. Make sure the power connector is not exposed to water.

15. Never attempt to charge a damaged battery.

16. The grid connection must comply with national electrical regulations.

17. Check the wiring of the charger before use. Never use the charger if the wiring is damaged.

18. When the battery is charging, place the charger on a non-flammable support, more than 1.5 m away from any

flammable object.

2.6. SAFETY SIGNAGE

California State Proposition 65:

Caution

This product contains or emits a chemical recognized by the State of California to cause cancer,

birth defects or other reproductive harm.

The RBRC™ sticker (found on the packaging) indicates that PELLENC voluntarily participates

in an industry program for the collection and recycling of used batteries in the United States

and Canada.

TYING MACHINE FIXION 2

29_133084-G

Tool compliant with Moroccan stan-

dards.

Tool compliant with EC standards.

Tool compliant with British stan-

dards

Lithium-ion battery.

At the end of its life, the battery

must be returned to the authorized

distributor from whom it was pur-

chased to be recycled in accor-

dance with waste regulations.

Do not expose to rain.

Please read the operating instruc-

tions.

2.7. PERSONAL PROTECTION EQUIPMENT

Equipment Wearing of

1 Safety helmet --

2 Protective visor --

3 Protective gloves Recommended

4 Safety footwear Recommended

5 Ear protection --

6 Protective goggles Recommended

7 Jacket or over-sleeves --

8 Work trousers --

Andere Handbücher für FIXION 2

Inhaltsverzeichnis

Andere pellenc Werkzeuge Handbücher

pellenc

pellenc FIXION 2 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung