* To order with B18CO, add the suffix "CO" to the
above part number. Additional conduit clips with
thread impression use the 4I extension. (EX. 812M4I)
Note:
May require dedicated drop wire/rod - consult local authority.
1.
Product intended for single and multiple runs of conduit.
2.
For single runs, extra leg may be bent of removed if needed.
When mounting box to B18 Bar and using screws, such as
3.
CADDY SMS8, two screws are required. When supporting the
CADDY B18 series with threaded rod going through both
the B18 and the box, this single support is appropriate.
Additional screws are not necessary.
Fig. 1 Fig. 2 Fig. 3
Fig. 4 Fig. 5
Fig. 6 Fig. 7
Fig. 8
Fig. 9
Sizing Chart
Global Part
Number
Fig.
Conduit/Cable
Installation Attachment
6MB18
1
MC/AC
Attaches to #12 wire
through 1/4" [6] rod or
1/8" [3] through 1/4" [6]
flange.
812MB18
1
1/2" [13] & 3/4" [19]
16MB18
1
1" [25]
MCS50B18
6
MC/AC
MCS100B18
6
MC/AC
6M3B18CO
8
MC/AC
6MB186
1
MC/AC
Attaches to 3/8" [10]
plain or threaded rod or
1/4" [6] through 3/8" [10]
flange.
812MB186
1
1/2" & 3/4"
16MB186
1
1" [25]
812MB188Z
1
1/2" [13] & 3/4" [19]
Attaches to 1/2" [13] &
5/8" [16] threaded rod
6MB1824
4
MC/AC
Attaches to 1/8" [3]
through 1/4" [6] flange.
812MB1824
4
1/2" [13] & 3/4" [19]
16MB1824
4
1" [25]
6MB1858
4
MC/AC
Attaches to 5/16" [8]
though 1/2" [13] flange.
812MB1858
4
1/2" [13] & 3/4" [19]
16MB1858
4
1" [25]
812MB18912
4
1/2" [13] & 3/4" [19]
9/16" [14] though 3/4"
[19] flange
6MB18A
2
MC/AC
1/4" [6] center hole for
screw or threaded rod
mount.
812MB18A
2
1/2" [13] & 3/4" [19]
16MB18A
2
1" [25]
MCS50B18A
7
MC/AC
6M3B18ACO
9
MC/AC
812MB18S
3
1/2" [13] & 3/4" [19]
1/4-20 x 5/8" [16] stud.
*(XXX)CO
5
Factory riveted assembly for multiple conduit
clips, mounting plate and oneclip, factory
riveted. Additional conduit clips ordered
seperately.
SMS8
-
Self tapping screws for mounting box to bar.
TECHNICAL SUPPORT:
www.erico.pentair.com
CFS223_J
INSTRUCTION SHEET
1 OF 4
© 1998-2017 Pentair All Rights Reserved
WARNING:
Pentair products shall be installed and used only as indicated in Pentair product instruction sheets and training materials. Instruction sheets are available at
1.
www.erico.pentair.com
and from your Pentair customer service representative.
PENTAIR products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be
completely
followed to ensure proper and safe installation and performance.
3.
Improper installation, misuse, misapplication or other failure to completely follow Pentair's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and/or death, and void your warranty.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
6.
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified
engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
Pentair, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by Pentair or its global affiliates. All other trademarks
are the property of their respective owners. Pentair reserves the right to change specifications without prior notice.
B18 Series
Combination Box and/or Conduit/Cable Hangers from
Drop Wire/Rod and Beam
