Pepperl+Fuchs HiC2821 Bedienungsanleitung

Release date 2014-06-17 14:11 Date of issue 2014-06-17 216711_eng.xml

HiC2821

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

Pepperl+Fuchs Group USA: +1 330 486 0002 Singapore: +65 6779 9091Germany: +49 621 776 2222

www.pepperl-fuchs.com [email protected].com [email protected].com [email protected]

Switch Amplifier

Zone 2

Div. 2

Zone 0, 1, 2

Div. 1, 2

HiC2821

Termination Board

10 kΩ

1.5 kΩ

10a

SL1

24 V DC

FAULT

1a, 1b

2a, 2b

SL2

Connection

Assembly

• 1-channel isolated barrier

• 24 V DC supply (bus powered)

• Dry contact or NAMUR inputs

• Usable as signal splitter (1 input and 2 outputs)

• Relay contact output

• Fault relay contact output

• Line fault detection (LFD)

• Up to SIL2 acc. to IEC 61508

Function

This isolated barrier is used for intrinsic safety applications. It

transfers digital signals (NAMUR sensors/mechanical

contacts) from a hazardous area to a safe area.

The proximity sensor or switch controls a form A normally

open relay contact for the safe area load. The module output

changes state when the input signal changes state. The mode

of operation can be reversed with switch S1 on the side of the

unit.

One additional relay is available for the fault output. Line fault

detection (LFD) can be selected or disabled via switch S2.

During an error condition, the relay reverts to its de-energized

state and the LEDs indicate the fault. A separate output bus is

available. The fault conditions can be monitored via a Fault

Indication Board.

This module mounts on a HiC Termination Board.

Features

PWR

HiC

2821

1 ch

Switch

Amplifier

CH1

STATUS/

FAU LT

LED green:

Power supply

Front view

LED yellow/red:

Status output/

Fault input

Place for

labeling

Switch 1 ... 4

Release date 2014-06-17 14:11 Date of issue 2014-06-17 216711_eng.xml

Technical data HiC2821

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

Pepperl+Fuchs Group USA: +1 330 486 0002 Singapore: +65 6779 9091Germany: +49 621 776 2222

www.pepperl-fuchs.com [email protected].com [email protected].com [email protected]

General specifications

Signal type Digital Input

Supply

Connection SL1: 1a(-), 1b(-); 2a(+), 2b(+)

Rated voltage 19 ... 30 V DC via Termination Board

Ripple ≤10 %

Rated current ≤30 mA

Power loss ≤500 mW

Power consumption ≤500 mW

Input

Connection SL2: 5a(+), 5b(-)

Rated values acc. to EN 60947-5-6 (NAMUR), see system description for electrical data

Open circuit voltage/short-circuit current approx. 10 V DC / approx. 8 mA

Switching point/switching hysteresis 1.2 ... 2.1 mA / approx. 0.2 mA

Line fault detection breakage I ≤0.1 mA , short-circuit I ≥6.5 mA

Pulse/Pause ratio ≥20 ms / ≥20 ms

Output

Connection SL1: 8a, 7a; 10a, 9a

Output I signal ; relay

Output II signal or error message ; relay

Contact loading 50 V DC / 0.5 A

Minimum switch current 2 mA / 24 V DC

Energized/De-energized delay ≤20 ms / ≤20 ms

Mechanical life 107switching cycles

Error message output

Connection SL1: 6b

Output type open collector transistor (internal fault bus)

Transfer characteristics

Switching frequency ≤10 Hz

Electrical isolation

Output/power supply basic insulation acc. to EN 50178, rated insulation voltage of 50 V AC

Output/Output basic insulation acc. to EN 50178, rated insulation voltage of 50 V AC

Directive conformity

Electromagnetic compatibility

Directive 2004/108/EC EN 61326-1:2006

Conformity

Electrical isolation EN 50178:1997

Electromagnetic compatibility NE 21:2006

For further information see system description.

Degree of protection IEC 60529:2001

Input EN 60947-5-6:2000

Ambient conditions

Ambient temperature -20 ... 60 °C (-4 ... 140 °F)

Mechanical specifications

Degree of protection IP20

Mass approx. 100 g

Dimensions 12.5 x 128 x 106 mm (0.5 x 5.1 x 4.2 in)

Mounting on Termination Board

Coding pin 1 and 2 trimmed

For further information see system description.

Data for application in connection

with Ex-areas

EC-Type Examination Certificate BASEEFA 06 ATEX 0093 X , for additional certificates see www.pepperl-fuchs.com

Group, category, type of protection ¬II (1)G [Ex ia Ga] IIC

¬II (1)D [Ex ia Da] IIIC

¬I (M1) [Ex ia Ma] I

Input [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I

Voltage Uo10.5 V

Current Io17.1 mA

Power Po45 mW (linear characteristic)

Supply

Maximum safe voltage Um253 V AC (Attention! Umis no rated voltage.)

Output

Contact loading 50 V DC / 0.5 A

Maximum safe voltage Um253 V AC (Attention! The rated voltage can be lower.)

Release date 2014-06-17 14:11 Date of issue 2014-06-17 216711_eng.xml

Technical data HiC2821

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

Pepperl+Fuchs Group USA: +1 330 486 0002 Singapore: +65 6779 9091Germany: +49 621 776 2222

www.pepperl-fuchs.com [email protected].com [email protected].com [email protected]

Configure the device in the following way:

• Push the red Quick Lok Bars on each side of the device in the upper position.

• Remove the device from Termination Board.

• Set the DIP switches according to the figure.

Statement of conformity PF 08 CERT 1047 X

Group, category, type of protection,

temperature class

¬II 3G Ex nA nC IIC T4 Gc

Electrical isolation

Input/Output safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V

Input/power supply safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V

Directive conformity

Directive 94/9/EC EN 60079-0:2009, EN 60079-11:2012 , EN 60079-15:2010

International approvals

FM approval

Control drawing 16-534FM-12 (cFMus)

IECEx approval IECEx BAS 06.0026X

Approved for [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I

General information

Supplementary information EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of

Conformity and instructions have to be observed where applicable. For information see www.pepperl-

fuchs.com.

The pins for this device are trimmed to polarize it according to its safety parameter. Do not change!

For further information see system description.

Configuration

S1 S4

Open - energized

Input to output operation

Function

Switch settings

Input fault detection

Fault enable

Fault disable

Second output

As CH1

As fault

No function S4

Close - de-energized

Close - energized

Open - de-energized

Refer to the Instruction

Manual to install and

operate the unit

CAUTION

S1 S4

Release date 2014-06-17 14:11 Date of issue 2014-06-17 216711_eng.xml

Technical data HiC2821

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

Pepperl+Fuchs Group USA: +1 330 486 0002 Singapore: +65 6779 9091Germany: +49 621 776 2222

www.pepperl-fuchs.com [email protected].com [email protected].com [email protected]

The maximum number of switching cycles is depending on the electrical load and may be higher when reduced currents and

voltages are applied.

Maximum switching power of output contacts

I (A)

10050 U (V)

0.5

0.3

Electrical life

max. 2.5 x 105switching cycles

Electrical life

max. 1 x 105switching cycles

Resistive load DC

Andere Pepperl+Fuchs Verstärker Handbücher

Pepperl+Fuchs

Pepperl+Fuchs HiD2842 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiD2822 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFA4-SR2-Ex1.W Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs SIL HiD282 Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs 2/208 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiC2831R1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiC2842 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiD2824 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFU8-SR-Ex1.W Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs SIL KFU8-SR-Ex W LB Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiD2844 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KCD2-SR Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFD2-GU-1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiC2832R1 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFD2-SR2-Ex1.W.LB Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiC2841 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KCD2-SR-1.LB Benutzerhandbuch

Pepperl+Fuchs

Pepperl+Fuchs KFD2-SR2-Ex Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KCD2-SON-Ex Series Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs FYQLA1-140R-3 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs 2/209 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFD2-SR2-Ex1.W Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs HiD2844 Bedienungsanleitung

Pepperl+Fuchs

Pepperl+Fuchs KFD2-SR3-2.2S Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung