Perle JETSTREAM 8500 Kurzanleitung

Inhaltsverzeichnis

Andere Perle Schalten Handbücher

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Perle

Perle 30th December 1998

Page 1of 2

Configuration of JETSTREAM 8500 & MTSRD for AIX 4.2

This is a quick installation guide for MTSRD on an AIX 4.2 system, to enable a login

on a terminal on a JETSTREAM 8500 port.

·Attach the JETSTREAM 8500 to the network and verify that it has an IP address,

broadcast address and subnet mask.

If not, add these using the following CLI commands, then reboot the

JETSTREAM.

set server internet 195.49.144.4

set server broadcast 195.49.144.255

set server subnet 255.255.255.0

save

·On the AIX system, add the JETSTREAM to the host table using smit, type:

smit

Then select ‘Communications Applications & Services’, ‘ TCPIP’,’ Further

Configuration’, ‘ Name Resolution’, ‘Hosts table’ ,’ Add a host’

·Install the mtsrd Software

cd /

installp -aX all

·Configure the JETSTREAM Ports

Log in to the JETSTREAM 8500 as admin, and type screen<cr>.

Use ‘network configuration’, ‘host table’, ‘add host’ and enter the AIX host

name and the TCP/IP address of this host to define the AIX host on the

JESTREAM.

Use ‘line configuration’ , ‘ line settings’ and select line 1

Set the service to SILENT RAW, enter the HOSTNAME of the AIX system

in the hostname field and set hostport to 10000

Set up further ports using hostport 10001 for line 2, hostport 10002 for line 3

and so on.

Perle

Perle 30th December 1998

Page 2of 2

·Update the /etc/mts/defaults file

Edit the file and change the MTS VERSION line to be:

MTS_VERSION JETSTREAM 8500 2.2.4 # JETSTREAM version

2.2.4 was our version of software; check the version you are using.

·Set up mtsrd ports on the AIX

Each JETSTREAM port must be configured on a different TCP port via smit,

type:

smit

Followed by selecting ‘Devices’, ‘ Communication’, ‘Specialix MTS’, ‘Add

Control Device’. Enter TCP/IP port number 10000.

Then ‘add a block of TTY ports’ with login set to enabled.

Attach a terminal to one of the JETSTREAM’s ports and you should see a

login.

Equipment used

JETSTREAM 8500 running version 2.2.4

WYSE 60 configured at 9600, 8 bit, 1stop, Np parity, Xon/Xoff flow control

AIX version 4.2.1