Philips Avent SCD480 Bedienungsanleitung

SCD480

3 4 5 6 7 8

4 6

SCD480

ENGLISH 6

DANSK 13

DEUTSCH 21

 29

SUOMI 38

FRANÇAIS 45

NEDERLANDS 53

ESPAÑOL 62

ITALIANO 70

NORSK 78

PORTUGUÊS 85

SVENSKA 92

TÜRKÇE 100

BAHASA INDONESIA 107

Introduction

Congratulations on your purchase and welcome to Philips AVENT! To fully benet from the support

that Philips AVENT offers, register your product at www.philips.com/welcome.

Philips AVENT is dedicated to producing caring, reliable products that give parents the reassurance

they need.This Philips AVENT baby monitor allows you to hear your baby from wherever you are in

and around your home.The sixteen different channel options guarantee minimal interference and a

secure reception, enabling you to be in constant contact with your baby.

General description (Fig. 1)

ABaby unit

1Microphone

2Socket for small plug

3On/off button

4Power-on light

5Microphone sensitivity control

6Channel selector

7Adapter

8Small plug

9Battery compartment lid

BParent unit

1Adapter

2Small plug

3Power-on light

4Loudspeaker

5Connection light

6Volume control with on/off function

7Connection alarm switch

8Battery compartment lid

9Channel selector

Important

Read these instructions for use carefully before you use the appliance and save them for future

reference.

Danger

- Never immerse any part of the baby monitor in water or any other liquid.

Warning

- Check if the voltage indicated on the adapters of the baby unit and the parent unit correspond

to the local mains voltage before you connect the appliance.

- Only use the adapters supplied to connect the baby unit and the parent unit to the mains.

- The adapters contain a transformer. Do not cut off the adapters to replace them with other

plugs, as this causes a hazardous situation.

- If the adapters are damaged, always have them replaced with one of the original type in order

to avoid a hazard. For the correct type, see chapter ‘Replacement’.

- Never use the baby monitor in moist places or close to water.

- Except for the battery compartments, do not open the housing of the baby unit or the parent

unit in order to prevent electric shock.

- This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their

safety.

ENGLISH

- Children should be supervised to ensure that they do not play with the appliance.

- The baby monitor has an operating range of 200 meters/600 feet in open air. Depending on the

surroundings and other disturbing factors, the operating range may be smaller (see section

‘Operating range’, in chapter ‘Using the appliance’.

Caution

- Use and store the appliance at a temperature between 10°C and 40°C.

- Do not expose the baby unit and parent unit to extreme cold, heat or direct sunlight.

- Make sure the baby unit and its cord are always out of reach of the baby (at least 1 metre/3

feet away).

- Never place the baby unit inside the baby’s bed or playpen.

- Never cover the parent unit and the baby unit with anything (e.g. a towel or blanket).

- Always place non-rechargeable batteries of the correct type in the baby unit and the parent

unit.

General

- This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult

supervision and should not be used as such.



This Philips AVENT appliance complies with all standards regarding electromagnetic elds (EMF). If

handled properly and according to the instructions in this user manual, the appliance is safe to use

based on scientic evidence available today.

Preparing for use

Baby unit

You can use the baby unit from the mains or on non-rechargeable batteries. Even if you are going to

use the unit from the mains, we advise you to insert the non-rechargeable batteries.This guarantees

automatic back-up in case of mains failure.

Mains operation

1 Put the appliance plug in the baby unit and put the adapter into a wall socket (Fig. 2).

The power-on light goes on.

Operation on non-rechargeable batteries

The baby unit runs on four 1.5V R6 AA batteries (not included).We strongly advise you to use

Philips LR6 PowerLife batteries.

Do not use rechargeable batteries, as the baby unit does not have a charging function.

Unplug the baby unit and make sure your hands and the unit are dry when you insert the non-

rechargeable batteries.

1 Unlock the battery compartment lid by turning the locking knob with a coin.Then remove

the lid (Fig. 3).

2 Insert four non-rechargeable batteries.

Make sure the + and - poles of the batteries point in the right direction.

3 Reattach the battery compartment lid and close it by turning the locking knob with a coin.

When the batteries are low, the power light on the baby unit ashes red.

Parent unit

You can use the parent unit from the mains or on non-rechargeable batteries. Even if you are going

to use the unit from the mains, we advise you to insert the non-rechargeable batteries.This

guarantees automatic back-up in case of mains failure.

ENGLISH 7

Mains operation

1 Put the appliance plug in the parent unit and put the adapter into a wall socket.

The power-on light goes on.

Operation on non-rechargeable batteries

The parent unit runs on four 1.5V R6 AA batteries (not included).We strongly advise you to use

Philips LR6 PowerLife batteries.

Do not use rechargeable batteries, as the parent unit does not have a charging function.

Unplug the parent unit and make sure your hands and the unit are dry when you insert the non-

rechargeable batteries.

1 Turn the locking knob a quarter turn (1) and slide the battery cover downwards to remove it

(2) (Fig. 4).

2 Insert four non-rechargeable batteries.

Make sure the + and - poles of the batteries point in the right direction.

3 Replace the battery compartment lid.

Note: When the batteries are low, the power light on the parent unit ashes red.

Note: When the batteries are completely empty, the parent unit automatically switches off and loses

contact with the baby unit.

Using the appliance

1 Place the two units in the same room to test the connection (Fig. 5).

Make sure the baby unit is at least 1 metre/3 feet away from the parent unit.

2 Press the on/off button to switch on the baby unit (Fig. 6).

The power-on light lights up green continuously.

3 Turn the volume control to switch on the parent unit and to set the volume to the level you

prefer. (Fig. 7)

The power-on light lights up green continuously.

,When a connection has been established between the units, the connection light on the

parent unit lights up green constantly.

Note: It takes about 30 seconds before a connection is established.

Note: If a connection cannot be established, the connection light on the parent unit ashes red.

4 Place the baby unit at least 1 metre/3 feet away from your baby (Fig. 8).

5 Place the parent unit within the operating range of the baby unit. Make sure it is at least 1

metre/3 feet away from the baby unit. For more information on the operating range, see

section ‘Operating range’ below (Fig. 9).

Operating range

The operating range of the baby monitor is 200 metres/600 feet in open air. Depending on the

surroundings and other disturbing factors, this range may be smaller.

Dry materials Material thickness Loss of range

Wood, plaster, plaster cardboard, glass

(without metal, wires or lead) <30cm/12in 0-10%

Brick, plywood <30cm/12in 5-35%

ENGLISH8

Dry materials Material thickness Loss of range

Reinforced concrete <30cm/12in 30-100%

Metal grilles or bars <1cm/0.4in 90-100%

Metal or aluminium sheets <1cm/0.4in 100%

For wet and moist materials, the range loss may be up to 100%.

Features



The parent unit has a link light that continuously advises you of the status of the connection

between the baby and the parent units.You can set an alert on the parent unit to notify you if the

link is lost. The alert will sound an audible beep and the link light will ash red when a connection is

lost.

To activate the alert on the parent unit:

1 Turn the locking knob a quarter turn (1) and slide the battery cover downwards to remove it

(2) (Fig. 4).

2 Set the link alarm switch in the battery compartment to the ‘on’ position.

3 Replace the battery compartment lid.

To switch off the alert, set the link alert switch to the ‘off’ position.

Adjustable sound sensitivity

With the microphone sensitivity control on the baby unit, you can set the sound that is picked up by

the baby unit to the desired level: low, mid or high.When the microphone sensitivity is set to ‘high’,

the baby unit picks up all sounds.

Note: The sensitivity of the baby unit can only be changed when there is a connection between the baby

unit and the parent unit.

1 Use the microphone sensitivity control to set the microphone sensitivity of the baby unit to

the desired level.You can use your own voice as a sound reference (Fig. 10).

The power-on light on the baby unit turns yellow when a sound is transmitted.

Note:Whilst operating on batteries, if the sensitivity is set to a high level, the parent unit will consume

more power.

Adjustable loudspeaker volume

You can change the volume on the parent unit, so you can adjust to suit your surroundings.

1 Turn the volume dial on the right side of the parent unit until the desired loudspeaker

volume for the parent unit has been reached.

Note:Whilst operating on batteries, if the volume is set to a high level, the parent unit will consume more

power.

Channel selector

Always make sure that the channel selectors inside the battery compartments of both units are set

to the same channel.With these channel selectors, you can select sixteen different channel positions.

If you experience interference from other baby monitors, radio devices etc., select a different

channel..

1 Open the battery compartment lids of both units.

ENGLISH 9

,Baby unit: (Fig. 3)

- Turn the locking knob with a coin and remove the lid.

- Remove the batteries from the battery compartment, if present.

- Use a small, at screwdriver to turn the channel selector to the desired position.

,Parent unit: (Fig. 4)

- Turn the locking knob a quarter turn (1) and slide the battery cover downwards to remove it

(2).

- Remove the batteries from the battery compartment, if present.

- Use a small, at screwdriver to turn the channel selector to the desired position.

Note: Make sure both units are set to the same channel.

If you do not experience any interference when you test the connection, close the battery

compartments of the baby and the parent units.

If you experience interference, set the selector to another channel and test the connection again.

If the units are operating on non-rechargeable batteries, replace the batteries and close the battery

compartments.

Cleaning and Maintenance

Do not immerse the parent unit or the baby unit in water and do not clean them under the tap.

Do not use cleaning spray or liquid cleaners.

- Unplug the baby unit or the parent unit if they are connected to the mains.

- Clean the parent unit and the baby unit with a damp cloth.

Make sure the units are dry before you connect them to the mains.

- Clean the adapters with a dry cloth.

Storage

When you are not going to use the baby monitor for some time, remove the non-rechargeable

batteries from the baby unit and parent unit. Store the baby unit, the parent unit and the adapters in

a cool and dry place.

Replacement

Baby unit

Batteries

Only replace the non-rechargeable batteries of the baby unit with four 1.5V R6 AA batteries.

Note: We strongly advise you to use Philips non-rechargeable batteries.

Adapter

Only replace the adapter of the baby unit with an adapter of the original type.You can order a new

adapter from your dealer or a Philips service centre:

- SBC CS0920/00W (EU/SGP only)

- SBC CS0920/05W (UK only)

- 9VD200 (AU/NZ only)

Parent unit

Batteries

Only replace the non-rechargeable batteries of the parent unit with four 1.5V R6 AA batteries.

Note: We strongly advise you to use Philips non-rechargeable batteries.

ENGLISH10

Inhaltsverzeichnis

Sprachen:

Andere Philips Babyphone Handbücher

Philips

Philips SBC SC466 Bedienungsanleitung

Philips

Philips Dect SC479 Bedienungsanleitung

Philips

Philips AVENT SCD845 Bedienungsanleitung

Philips

Philips SCD469/05 Bedienungsanleitung

Philips

Philips AVENT SCD535 Bedienungsanleitung

Philips

Philips AVENT SCD486H1 Bedienungsanleitung

Philips

Philips SBCSC365 Bedienungsanleitung

Philips

Philips AVENT DECT SCD535/00 Bedienungsanleitung

Philips

Philips SBCSC368/00Y Bedienungsanleitung

Philips

Philips SKM7488NC/84 Bedienungsanleitung

Philips

Philips AVENT SCD501 Bedienungsanleitung

Philips

Philips AVENT SCD860 Bedienungsanleitung

Philips

Philips AVENT SCD503/26 Bedienungsanleitung

Philips

Philips SBCSC464 Bedienungsanleitung

Philips

Philips SCD463/79 Bedienungsanleitung

Philips

Philips AVENT SCD720 Bedienungsanleitung

Philips

Philips SCD590 Bedienungsanleitung

Philips

Philips Avent SCD506 Bedienungsanleitung

Philips

Philips Analogue monitor SCD450 Bedienungsanleitung

Philips

Philips Avent SCD730 Bedienungsanleitung

Philips

Philips SBCSC468/00 Bedienungsanleitung

Philips

Philips AVENT SCD501 Bedienungsanleitung

Philips

Philips SBC SC 477 Bedienungsanleitung

Philips

Philips Avent SCD506 Bedienungsanleitung

Beliebte Babyphone Handbücher anderer Marken

Motorola

Motorola MBP15 Bedienungsanleitung

Oricom

Oricom Babysense 7 Bedienungsanleitung

Levana

Levana TW502 Bedienungsanleitung

Luvion

Luvion Essential Bedienungsanleitung

NUK

NUK Eco Control Video Display 550VD Bedienungsanleitung

Lorex

Lorex sweet peek mini Bedienungsanleitung

Mondevices

Mondevices MonBaby 2 Bedienungsanleitung

Famidoc

Famidoc FDBB-V2 Bedienungsanleitung

Graco

Graco iMonitor 2797 Bedienungsanleitung

babymoov

babymoov High Care A014001 Bedienungsanleitung

Ramili

Ramili RV1000 Bedienungsanleitung

Swann

Swann SW231-FLO Bedienungsanleitung

Badabulle

Badabulle Baby Online 300 m+ Bedienungsanleitung

Philips AVENT

Philips AVENT SCD526/00 Bedienungsanleitung

Uniden

Uniden Guardian UBR223 Bedienungsanleitung

Summer

Summer Day & Night 28470A Bedienungsanleitung

Ivation

Ivation Wireless Monitoring System Bedienungsanleitung

Levana

Levana Lila Bedienungsanleitung