Philips DYNALITE DDRC420FR Bedienungsanleitung

DDRC420FR

4 x 20A Relay Controller

Instruction Manual

features

4 x Feed Thru Outputs –Latching Relays rated at 20A inductive, no

de-rating necessary

Separate Control Supply –1 phase at 0.1A

Manual Overrides for each channel

Powerful Internal PLC –Custom scripts can be written to provide

process control based on conditional logic.

Many Control Options –Control of this device can be via a

combination of methods eg. Serial control port, relay contacts, push

button control panels, infrared receivers and timeclocks.

Simple Installation –DIN Rail mount facilitates installation.

All connection terminals accessible without disassembly.

Warning –this device is a class A product. In a domestic environment this

product may cause radio interference, in which case the user may be required

to take adequate measures.

Manual Override Switches –These switches do not provide permanent

isolation. Isolate at the supply before performing work on load circuits.

Special Programming –Once powered and terminated correctly this device

will only operate in basic mode. A new Dynalite panel will turn on all lighting

channels from button 1 and turn off from button 4 if network terminations are

correct. Only once the full network is test correct can commissioning begin.

Advanced functions can be commissioned via Envision software. If

commissioning is required, contact your local distributor for details.

Check Connections –Tighten all load-carrying screw connections, as

vibrations from transport can cause terminal block screws to become loose.

Power Sources –This device should only be operated from the type of supply

specified on the front cover. This device must be earthed.

Output Circuits –The load circuit should not exceed the specified capacity of

20A. Loads should be calculated to ensure that the overall maximum capacity

of 80A is not exceeded. Each channel shall be protected with a HRC fuse or

MCB rated 20A or less. Output circuits are suitable for Single Phase or Three

Phase Star (with Neutral) only, Delta wiring is not supported.

Mounting Location –Install in a dry, well-ventilated location. Controllers may

emit some mechanical noise. Take this into account when deciding the

mounting location.

Data Cable –Use screened, stranded RS485 data cable with three twisted

pairs. Segregate from mains cable by 300mm minimum. Connect devices in a

‘daisy chain’. A data cable connected to an energized device is live. Do not

cut or terminate live data cables.

electrical diagram

To reduce the risk of fire or electric shock, do

not expose this device to rain or moisture. Do

not energise unless the front cover is in place.

The device must be earthed. Installation,

programming and maintenance must be carried

out by qualified personnel.

………

All manuals and user guides at all-guides.com

all-guides.com

connecting data cable

installation steps

1. Mount the device on a DIN rail inside an approved enclosure.

2. Calculate loads to ensure any channels are not overloaded, then connect loads to the output channels. The maximum loading of this device is as

follows:

Maximum Channel Load: 20A 230V AC

Total Box Load: 80A

Connect supply and load cables to each channel. Note that this device must have an individual supply circuit for each channel. The supply circuits

can be on any phase. Note that loads must have a Neutral (1 Phase or 3 Phase Star), Delta wiring is not supported.

3. Connect a single phase 0.1A feed to the supply terminals. This device must be earthed.

4. Connect data cables to the device as per the diagrams below.

5. If the Auxiliary input is to be used, connect a dry contact device in between the AUX and GND terminals. Keep cable runs between the AUX

terminals and the dry contacts under two metres. The function of the Auxiliary input will need to be programmed at the time of commissioning.

product specifications

Supply:

100-240V 50/60Hz Single Phase at 0.25A

Load Outputs:

4 x Feed Thru Outputs at 20A per channel, maximum device load of 80A

Wiring topology: 1 Phase & Neutral and 3 Phase & Neutral Star. Delta not supported

Switching Device:

Relay –50A 230V AC inductive (5000W Lighting Load rated)

Supply Terminals:

1 x Phase, 1 x Neutral, 1 x Earth, up to 1 x 4mm2cable per terminal

Load Terminals:

IN, OUT for each channel, up to 1 x 4mm2cable per terminal

IO:

1 x RS485 DyNet/DMX512 Serial port

1 x AUX programmable dry contact input

DyNet DC Supply:

120mA (Supply for approx 6 panels)

Preset Scenes:

170

Compliance:

CE, C-Tick

Operating Environment:

0° to 50°C ambient temperature

0% to 90% RH non-condensing

Construction:

Polycarbonate plastic DIN rail mount

Dimensions:

H 93mm xW 105mm x D 75mm

Weight:

0.8kg

DDRC420FR Instruction Manual Rev G.doc. Specifications subject to change without notice.

Dynalite manufactured by WMGD Pty Limited (ABN 33 097 246 921). Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: +61 2 8338 9899 Fax: + 61 2 8338 9333

E-mail: dynalite.info@philips.com Web: philips.com/dynalite

All manuals and user guides at all-guides.com

Andere Philips Controller Handbücher

Philips

Philips 9890 000 0268 Series Bedienungsanleitung

Philips

Philips Dynalite Revolution Series Bedienungsanleitung

Philips

Philips iColor Keypad Bedienungsanleitung

Philips

Philips iPlayer 3 Bedienungsanleitung

Philips

Philips ColourChaser Touch Bedienungsanleitung

Philips

Philips dynalite DBC1210 Bedienungsanleitung

Philips

Philips Vaya Touch Controller Bedienungsanleitung

Philips

Philips CoralCare Bedienungsanleitung

Philips

Philips LFH 2305 Bedienungsanleitung

Philips

Philips Dynalite DMC2 Bedienungsanleitung

Philips

Philips dynalite DBC1220GL Bedienungsanleitung

Philips

Philips Strand Lighting Sixer Bedienungsanleitung

Philips

Philips Dynalite DMC-GRMS-UL Bedienungsanleitung

Philips

Philips LLC7811/00 Bedienungsanleitung

Philips

Philips LFC7310/00 Bedienungsanleitung

Philips

Philips dynalite DMRC210-RJ-DA Bedienungsanleitung

Philips

Philips Dynalite DMAL120F Bedienungsanleitung

Philips

Philips 9290 014 61062 Bedienungsanleitung

Philips

Philips Dynalite DDBC300-DALI Bedienungsanleitung

Philips

Philips Dynalite DDBC1200 Bedienungsanleitung

Philips

Philips AntumbraButton Bedienungsanleitung

Philips

Philips iPlayer 3 Bedienungsanleitung

Philips

Philips DYNALITE DDRC1220FR-GL Bedienungsanleitung

Philips

Philips Dynalite DMRC210DA-RJ12 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch