Philips EasyKey 9000 Series Bedienungsanleitung

Contents

5 How to use EasyKey 15

6 Other Functions 18

7 The Use and Meanings of

Indicators 20

8 Troubleshooting 22

Indoor Infrared Sensor Unlock

Restore to Default Settings

Mute Button

Outside Forced Lock

Door Lock Status Indicator

Low Battery Voltage Indicator

Outside Forced Lock Indicator

Mute Indicator

Inside Deadlock Indicator

System Lock-up Indicator

[OPEN/CLOSE] Indicator

Indoor Infrared Sensor Unlock

Indicator

Alarm Types and Methods

How to use an Emergency Power

Supply

How to Replace Batteries

Unlock

Unlock from Outside

-With a PIN Code

-With a Fingerprint

-With a Key Tag/Card

Unlock from Inside

-With a Rotatory Knob

-With a Functional Button

-With an Infrared Sensor

Lock

-Auto/Manual Mode

-Lock from Outside

-Lock from Inside

Indoor Deadlock

Mechanical Key Opening

1 Important Information 02

2 EasyKey Installation 03

3 Get to know your

EasyKey 08

4 How to set up your

EasyKey 09

Safety

Warning

Disposal of used products

and batteries

Packing List

Exploded Views

Pre-install Instruction

Installation Steps

Outside Escutcheon

Inside Escutcheon

-Pre-setup Instruction

-Modify Master PIN Code

-User Settings

-Delete a user record

-System Settings

-Extended Functions

-System Query

-Local Query

-Bluetooth Settings

2 3

① Outside Escutcheon

with Silicone Pad

⑤ Mounting Plate

⑨ Certicate of

Conformity

⑬Installation kit

② Inside

Escutcheon with

Silicone Pad

⑥ User Manual

⑩Key Tag X 2

⑭Cleaning Pad

③ Drilling Template

⑦ QSG

⑪Mechanical

Key X 2

④ Mortise

⑧ Warranty Card

⑫Batteries

Strike

EasyKey

User Manual Quick Start

Guide

EasyKey

Warranty

Card

EasyKey

合格证

Gateway

1 Important information

Safety

◆Before using Philips EasyKey, please

read and understand all instructions.

Damage caused by non-compliance with

the instructions will not be covered by

warranty.

◆Use only the manufacturer-specied

accessories/components.

◆Use only the alkaline batteries the

product is equipped with, or use the

same specification type of alkaline

batteries.

◆Do not forcibly disassemble this product

to avoid triggering an alarm or damaging

the product.

◆Do not scrape the ngerprint sensor

with sharp objects, otherwise it may cause

permanent damage.

◆Do not expose products to environments

where there is water leakage or splashing.

◆Do not expose the product to corrosive

substances to prevent damaging the

protective cover.

◆Do not hang objects on the handle, in

case it might aect the normal use of the

lock.

◆Pleae clean the product with a soft cloth.

◆Do not remove the battery during

setting up and operating.

◆Please let a professional technician

to install the door lock and follow the

installation guidelines provided.Do not

disassemble the lock by yourself. Keep the

relevant sealed stickers properly. Do not

easily disclose the password information.

◆Please modify the default master PIN

code immediately after nishing installing

and debugging, and keep the mechanical

key properly.

◆Please replace all the batteries

immediately if there is a low battery alarm.

Please make sure to correctly match the

poles (+/-) when installing the batteries.

Caution

◆Do not place the battery near re

sources to avoid explosion.

◆Do not use any emergency power

supply that does not meet the safety

requirements to power up the product.

◆Do not connect the 2 poles of the

batteries with metals to avoid short circuit

which may lead to an explosion.

◆Please make sure any component

replacement is executed by Philips, Philips

authorized service center or professional

technicians.

◆Do not use accessories or parts that have

been produced by other manufacturers or

have not been specically recommended

by Philips. The use of such accessories and

parts may void your warranty.

Disposal of used products and

batteries

◆You can have your locks reclaimed at

Philips authorized service centers. You will

receive corresponding compensation if

your products meet our conditions.

◆Please familiarize yourself with the local

electronic product collection system.

◆Please follow local regulations and do

not discard used products into ordinary

household waste.

◆Proper disposal of used products can

help to avoid potential negative impacts

on the environment and human health.

◆Batteries must not be disposed of with

ordinary household waste.

◆Please familiarize yourself with the local

regulations on batteries classication

recycling. Disposing of batteries properly

can help avoid a negative impact on the

environment and human health.

2 Easykey Installation

Packing List

This packing list is for reference only. Please refer to the actual packing items.

4 5

Exploded Views

1. Deco Cover

2. M6 Connecting Screw

(X1)

3. Upper Mounting

Plate Set (X1)

4. M6 Connecting Screw

Tube (X 2)

5. Outside Escutcheon

(X1)

6. Battery Cover

7. M6 Anchor Screw (X2)

8. Inside Escutcheon

(X1)

9. Compressed Spring

(X2)

10. Square Shaft (X2)

11. M5 Connecting Screw

(X4)

12. Mounting Plate (X1)

13. Mortise (X1)

14. M5 Connecting

Screw Tube (X4)

Pre-install Instruction

This product can be installed on 4 types of opening directions: left-out pull,

right-in push, right-out pull and left-in push.

Left-open Right-open

Left-in

push Right-

in push

Indoor Indoor

Outdoor Outdoor

Left-

out pull Right-

out pull

1. Please choose proper installation kit as per the door thickness.

2. The default installation kit is applicable for a door thickness of 38-60mm, if your door thickness

does not within this range, please feel free to contact us.

Attention

6 7

First x the mounting plate

against the inner surface of the

door, and fasten it with 4 M5

connecting screws, and then x the

upper mounting plate with M6

connecting screws.

Fasten the 4 anchor

screws in the

mortise.

The latch bolt can’t be poped

up during installation.

Pass the connecting cable through

the hole above the door. Align

the square shaft of the outside

escutcheon with the two rotary

holes on the mortise, then

insert the square shaft into the

rotary holes, so that the outside

escutcheon is close t in the outside

door.

Installation Steps

Please use the appropriate

square shaft and connecting

tubes with proper length.

To install the connecting

screw tubes on the outside

escutcheon, and put the

compressed spring and

square shaft accordingly

into the square shaft

holes.

To drill the needed

holes in the door

as per the drilling

template,then mount

the mortise on the

door frame.

Unscrew the deco

cover by turning it

counterclockwise, and

press the battery cover

button to remove the

battery cover. Then

the two M6 mounting

screws can be installed

to fasten the inside

escutcheon.

After completing the installation

of the strike,please check whether

the smart lock can be used

normally.

Turn clockwise to

install the deco cover,

install the battery, put

the battery cover back,

and after attach the

strike, the installation

of the smart lock is

complete.

To check whether

if the rotary knob,

mechanical keys,

and all other

components could

be used normally.

Insert the outside escutcheon

connection cable and the motor

cable into the corresponding

sockets on the inside escutcheon,

and then connect the front and

rear Bluetooth connecting cables,

and then align the square shaft

of the inside escutcheon with the

two rotary holes on the mortise,

then insert the square shaft into

the rotary holes, so that the inside

escutcheon is close t in the inside

door.

Put the compressed spring and

square shaft into the square shaft

hole of the inside escutcheon

accordingly.

Be sure to hide the extra mortise and the

escutcheon connecting cables in the door hole,

and also hide the extra Bluetooth connecting

cable in the inside escutcheon.

M6 Connecting

Screw Tube

Mortise Connecting

Cable

Escutcheon

Connecting Cable

Battery cover

button

Front Bluetooth

Connecting Cable

M5 Connecting

Screw Tube

Front Bluetooth

Connecting Cable Escutcheon

Connecting Cable

Front Bluetooth

Connecting Cable

Mortise Connecting

Cable Socket

Escutcheon Connecting

Cable Socket

Rear Bluetooth

Connecting Cable

Attention Attention Attention

Attention

8 9

Handle

Battery Cover

Auto/Manual Mode

Switch

RESET

OPEN/CLOSE Button

Rotary Knob

Battery Cover

3 Get to know Your EasyKey

Inside Escutcheon

4 How to set up your EasyKey

Pre-install Instruction

◆There are two modes for the EasyKey System: general mode and dual verication

mode.

◆User Code

When you want to delete one single user record, you could delete it in the system by

deleting its user code.

◆You could ll in the below blank sheet with the user information in case you might

need to check or review in the future.

1.Press [*] key to return to the previous menu.

2.The default master PIN code is 12345678.

Unlock with any of the

registered identify methods Unlock with any two of the registered identify

methods among PIN code, Key Tag, and

Fingerprint

General Mode Dual Verication Mode

Outside Escutcheon

Fingerprint Sensor

Keypad

Mute Button

Outside Forced Lock

Button

Lock Status Indicator

Handle

Card Reader

Low Battery Voltage

Indicator

RESET

Mechanical Key

Emergency Power

Supply Interface

9 10

Network Communicat

-ion Module Interface

CardPIN CodeFingerprintNameNumber

◆Icon annotation

Master

PIN code

One-time

user PIN

code

User

code

00-99

User PIN

code

User

code

00-09

Finger

Key Tag/

Card

# *

Attention

10 11

◆How to enter into Master Mode

Light up the

keypad.

Press [#] before inputting any other

numbers. After hearing a voice prompt

of "Enter master PIN code", enter your

master PIN code and conrm with [#].

Then you are in master mode.

Add a one-time User PIN Code

Delete a User Record

Delete a single User PIN Code

Delete All User PIN Codes

Add a Fingerprint

Add a Key Tag

Modify master PIN code

Enter the new master PIN code and

conrm with [#] again. Re-enter

the same master PIN code and

conrm with [#]. After hearing a

voice prompt of “Succeeded”, press

[*] to return to previous menu until

you nally exit master mode.

Enter [1] to modify master PIN code.

Enter [#], enter master PIN code and

conrm with [#].

Enter [#], then enter master PIN code

and conrm with [#].

Enter [2] to add a user record, then enter

[1] to add a new user PIN code, and the

system will automatically number it and

generate a voice prompt.

Enter a user PIN code of 6 to 12 digits

and conrm with [#]. Then re-enter the

user PIN code and conrm with [#]. After

hearing a voice prompt of “Succeeded”,

press [*] until you exit master mode.

User settings

Add a user PIN code

Enter [#], enter master PIN code and

conrm with [#].

Enter a one-time user PIN code of 6 to

12 digits and conrm with [#]. Then re-

enter the one-time user PIN code and

conrm with [#]. After hearing a voice

prompt of “Succeeded”, press [*] until

you exit master mode.

Enter [2] to enter into user setting, then

enter [2] again to add a one-time user PIN

code.

2 2

Enter [#], enter master PIN code and

conrm with [#].

Place your nger against the sensor.

After hearing a voice prompt of “Take

away your nger and enroll again”,

please take away your nger and re-

place it against the sensor. After hearing

a voice prompt of “Succeeded”, press [*]

until you exit master mode.

Enter [2] to add a user record, then enter

[3] to add a user ngerprint, and the

system will automatically number it and

generate a voice prompt.

Enter [#], enter master PIN code and

conrm with [#].

Enter [2] to add a user record, then

enter [4] to add a user key tag, and the

system will automatically number it and

generate a voice prompt.

Place the key tag against the card reader

until you hear a beep. After hearing a

voice prompt of “Succeeded”, press [*]

until you exit the master mode.

1 13

Enter [#], enter master PIN code and

conrm with [#].

Enter [3] to delete a user record, then

enter [1] to delete a user PIN code, and

then enter [1] to delete a single user PIN

code.

Enter a user code (code: 00-09) of 2

digits and conrm with[#]. After hearing

a voice prompt of “Succeeded”, press [*]

until you exit the master mode.

Enter [3] to delete a user record, then

enter [1] to delete a user PIN code, and

then enter [2] to delete all user PIN

codes. After hearing a voice prompt of

"Succeeded", press [*] until you exit the

master mode.

Enter [#], enter master PIN code and

conrm with [#].

12 13

System Initialization

Remove the battery cover, then double

press the [RES] hole with a sharp

object, after hearing a voice prompt of

“Restoring to default settings”, all user

information will be emptied.

Delete all One-time PIN Codes

Enter [#], enter master PIN code and

conrm with [#].

Enter [3] to delete a user record, then

enter [2] to delete all one-time user PIN

code.

After hearing a voice prompt of

“Succeeded”, press [*] until you exit the

master mode.

Enter the 2-digit [user number] (00-99)

of the ngerprint that is to be deleted

and conrm with [#]. After hearing a

voice prompt of “Succeeded”, press [*]

until you exit the master mode.

Enter [3] to delete a user record, then

enter [3] to delete ngerprint record,

and then enter [1] to delete one single

ngerprint record.

3 3

Enter [#], enter master PIN code and

conrm with [#].

Delete a Fingerprint

Enter [3] to delete a user record, then

enter [3] to delete ngerprint record, and

then enter [2] to delete all ngerprint

records. After hearing a voice prompt of

"Succeeded", press [*] until you exit the

master mode.

3 3

Delete All Fingerprints

Enter [#], enter master PIN code and

conrm with [#].

Enter [3] to delete a user record, then

enter [4] to delete key tag record, and

then enter [1] to delete one single key

tag record. After hearing a voice prompt

of “Succeeded”, press [*] until you exit

the master mode.

Delete a Key Tag

Enter [#], enter master PIN code and

conrm with [#].

Enter [3] to delete a user record, then

enter [4] to delete key tag record, and

then enter [2] to delete all key tag

records. After hearing a voice prompt of

"Succeeded", press [*] until you exit the

master mode.

Delete All Key Tags

Enter [#], enter master PIN code and

conrm with [#]. Choose the language as needed: For

Chinese, press [1]; for English, press

[2]. After hearing a voice prompt of

“Succeeded”, press [*] until you exit the

master mode.

Enter [4] to get into system settings,

then enter [1] to get into language

settings.

The default language is English.

Language Settings

or 2

Enter [#], enter master PIN code and

conrm with [#].

System Settings

Attention

The default volume is “high volume”.

Choose the volume as needed: For

high volume, press [1]; for low volume,

press [2]; for mute mode, press [3]. After

hearing a voice prompt of “Succeeded”,

press [*] until you exit the master mode.

Enter [4] to get into system settings, then

enter [2] to enter into volume settings.

Volume Settings

or or

Enter [#], then enter master PIN code

and conrm with [#].

Attention

or 2

Enter [4] to get into system settings,

then enter [3] to enter into identify

verication methods portfolio.

For single verication method, press

[1]; for dual verication method, press

[2]. After hearing a voice prompt of

“Succeeded”, press [*] until you exit the

master mode.

Switch to Dual Verication Mode

Enter [#], then enter master PIN code

and conrm with [#].

14 15

Unlock | Unlock from Inside

Touch and wake up

the keypad, then enter a

registered user PIN code

and conrm with [#].

After hearing a voice

prompt of “Door opened”,

push or pull the handle to

open the door.

Place the nger of

which the ngerprint has

been registered against

the sensor.

After hearing a voice

prompt of “Door opened”,

push or pull the handle to

open the door.

Place the key tag/

card that has been

successfully registered

properly against the card

reader.

After hearing a voice

prompt of “Door opened”,

push or pull the handle to

open the door.

Features with an infrared

sensor on the handle, when

the sensor is triggered, hold

the handle’s sensor modules

on both the front and rear

side simultaneously,you

could easily unlock the door.

Double press the [OPEN/

CLOSE] functional button

within one second, then

push or pull to unlock.

With a Rotary Knob With a Functional

Button

With an Infrared

Sensor

Philips EasyKey employs

indoor fast opening

mortise. You can unlock

from inside by rotating

the rotary knob.

The extended functions are optional.

or 2

Enter [5] to get into extended functions.

To join a network, press [1]. To exit a

network, press [2]. Before setting up the

extended functions, please download

and open Philips EasyKey (APP) from

App Stores via your phone.

Enter [#], enter master PIN code and

conrm with [#].

Extended Functions

Attention

Enter [6] to get into system query, then

enter [1] to get into security code query,

the system will broadcast the product

series number automatically.

Directly input 400# could enter into system

query.

Security Code Query

Enter [#], enter master PIN code and

conrm with [#].

System Query

Attention

Local Query

Enter [6] to get into system query,

then enter [2] to get into product

software version query, the system will

broadcast the product software version

automatically.

Directly input 114# could enter into local query.

Enter [#], enter master PIN code and

conrm with [#].

Attention

Enter [7] to get into Bluetooth settings

menu.

To disable Bluetooth, please press [3].

After hearing a voice prompt of “Settings

succeeded”, press [*] until you exit the

master mode.

Enter [#], then enter master PIN code

and conrm with [#].

Bluetooth Settings

Attention

1.Directly input 403# to enable Bluetooth, and

input 404# to disable Bluetooth.

2.When the Bluetooth is o, please press [1] to

enable Bluetooth.

3. When using the newly updated EasyKey App

to bind with the smart lock, users could follow

up the chapter of “Add a device” to nish the

binding process.

5.How to use your EasyKey

Unlock | Unlock from outside

With a PIN code

Push or

pull to

unlock

Push or

pull to

unlock

Push or

pull to

unlock

Keypad

With a ngerprint

Fingerprint

sensor

Card

reader

With a Key Tag

16 17

Lock | Auto/Manual Mode

When the door is under auto mode, the latch bolt will be popped

up after closing the door, and there will be a voice prompt of “Door

Close”.

When the door is under auto mode, the latch bolt will be popped

up after closing the door, and there will be a voice prompt of “Door

Close”.

When the door is under manual mode, the latch bolt won’t pop

up after closing the door. Only after a successful verication

among any of the registered identity methods (PIN Code/Key Tag/

Fingerprint), the latch bolt will pop up, and there will be a voice

prompt of “Door Close”. When it is under manual mode and the door

is closed, waking up the outside escutcheon and unlock the system

could directly open the door.

When the door is under manual mode, the latch bolt won’t be

popped up after closing the door. Click on [CLOSE] and the latch

bolt will be popped up. After successfully locking the door, the

system will generate a voice prompt of “Door Close”.

Lock from Outside

Lock from Inside

[A] indicates auto

mode, after closing

the door, the latch

bolt will pop up, and

the door is lock.

[M] indicates manual

mode, after closing

the door, the latch

bolt will not pop up,

and the door is open.

Inside Deadlock

Mechanical Key Opening

When the EasyKey is locked, long-press the

[CLOSE] button, after the indicator ashes once

in red, and there will be a voice prompt of “Inside

deadlock enabled”.

Under inside deadlock mode, all functions of the

outside escutcheon will be locked. If you try to wake

up the system manually, the keypad area will display

the combination of “15937(X)” and there will be a voice

prompt of “Inside deadlock enabled” reminding you

that the door has been deadlocked from inside. Under

deadlock mode, all operations of the outside escutcheon

are disabled. Master PIN code verication or mechanical

key opening is required to release the door from deadlock

mode.

Cut the box and take

out the mechanical

keys. Push the cover

aside and reveal the

key itself.

Insert the key into

the keyhole and keep

the key and key shell

vertical to each other.

Rotate the key shell

towards the handle for

90°until it closes to

the door surface.

Rotate the key shell

downwards for 180° to

make it parallel to the

ground. Then rotate it

horizontally towards

the handle to unlock

the door.

It is suggested you not to use the mechanical key for daily unlocking. Use the key for emergencies

only, in case the battery is dead, forget the PIN code, or the system fails to work properly.

Lock | Auto/

Manual switch

Attention

Push Button

Andere Handbücher für EasyKey 9000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Türschloss Handbücher

Philips

Philips EasyKey 7100DS Bedienungsanleitung

Philips

Philips EasyKey 5100 Bedienungsanleitung

Philips

Philips DDL503-13HBS Bedienungsanleitung

Philips

Philips EasyKey DDL702E Bedienungsanleitung

Philips

Philips EasyKey 7000 Series Bedienungsanleitung

Philips

Philips EasyKey 7200 Bedienungsanleitung

Philips

Philips Home Access 4000 Series Bedienungsanleitung

Philips

Philips EasyKey 3000 Series Bedienungsanleitung

Philips

Philips EasyKey Alpha Bedienungsanleitung

Philips

Philips EasyKey Alpha Series Bedienungsanleitung

Philips

Philips EasyKey DDL702 Bedienungsanleitung

Philips

Philips Alpha Series Bedienungsanleitung

Philips

Philips DDL173LCGBB/97 Bedienungsanleitung

Philips

Philips EasyKey Bedienungsanleitung

Philips

Philips EasyKey 5000 Series Bedienungsanleitung

Philips

Philips EasyKey 7000 Series Bedienungsanleitung

Philips

Philips EasyKey Bedienungsanleitung

Philips

Philips EasyKey DDL151Z00BB/97 Bedienungsanleitung

Philips

Philips EasyKey 7000 Series Bedienungsanleitung

Philips

Philips DDL193LAFCG/97 Bedienungsanleitung

Philips

Philips EasyKey Alpha Series Bedienungsanleitung

Philips

Philips EasyKey 7100 Bedienungsanleitung

Philips

Philips EasyKey 5100 Bedienungsanleitung

Philips

Philips EasyKey 9000 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung