Philips EvoKit 2x4 P 36L 36W 835 2 0-107 G2 Bedienungsanleitung

Installation guide

Philips EvoKit LED 2x4 and 2x2

Products 2x4

EvoKit 2x4 P 36L 36W 835 2 0-10 7 G2

EvoKit 2x4 P 36L 36W 840 2 0-107 G2

EvoKit 2x4 P 36L 34W 835 1 Mk10 7 G2

EvoKit 2x4 P 36L 34W 840 1 Mk10 7 G2

EvoKit 2x4 P 36L 33W 835 5 Mk10 7 G2

EvoKit 2x4 P 36L 33W 840 5 Mk10 7 G2

EvoKit 2x4 P 36L 34W 830 1 Mk10 7 G2

EvoKit 2x4 P 36L 33W 830 5 Mk10 7 G2

EvoKit 2x4 P 36L 36W 830 2 0-10 7 G2

EvoKit 2x4 P 42L 39W 835 2 0-10 7 G2

EvoKit 2x4 P 42L 39W 840 2 0-10 7 G2

EvoKit 2x4 P 42L 40W 835 1 Mk10 7 G2

EvoKit 2x4 P 42L 40W 840 1 Mk10 7 G2

EvoKit 2x4 P 42L 42W 835 5 Mk10 7 G2

EvoKit 2x4 P 42L 42W 840 5 Mk10 7 G2

EvoKit 2x4 P 42L 40W 830 1 Mk10 7 G2

EvoKit 2x4 P 42L 42W 830 5 Mk10 7 G2

EvoKit 2x4 P 42L 39W 830 2 0-10 7 G2

EvoKit 2x4 P 52L 51W 835 2 0-10 5 G2

EvoKit 2x4 P 52L 51W 840 2 0-10 5 G2

EvoKit 2x4 P 52L 52W 835 1 Mk10 5 G2

EvoKit 2x4 P 52L 52W 840 1 Mk10 5 G2

EvoKit 2x4 P 52L 53W 835 5 Mk10 5 G2

EvoKit 2x4 P 52L 53W 840 5 Mk10 5 G2

EvoKit 2x4 P 52L 52W 830 1 Mk10 5 G2

EvoKit 2x4 P 52L 53W 830 5 Mk10 5 G2

EvoKit 2x4 P 52L 51W 830 2 0-10 5 G2

This installation guide is only valid for the following Philips EvoKit models:

Products 2x2

EvoKit 2x2 P 23L 23W 835 2 0-10 7 G2

EvoKit 2x2 P 23L 23W 840 2 0-10 7 G2

EvoKit 2x2 P 23L 23W 835 1 Mk10 7 G2

EvoKit 2x2 P 23L 23W 840 1 Mk10 7 G2

EvoKit 2x2 P 23L 25W 835 5 Mk10 7 G2

EvoKit 2x2 P 23L 25W 840 5 Mk10 7 G2

EvoKit 2x2 P 23L 23W 830 1 Mk10 7 G2

EvoKit 2x2 P 23L 25W 830 5 Mk10 7 G2

EvoKit 2x2 P 23L 23W 830 2 0-10 7 G2

EvoKit 2x2 P 32L 31W 835 2 0-10 7 G2

EvoKit 2x2 P 32L 31W 840 2 0-10 7 G2

EvoKit 2x2 P 32L 32W 835 1 Mk10 7 G2

EvoKit 2x2 P 32L 32W 840 1 Mk10 7 G2

EvoKit 2x2 P 32L 34W 835 5 Mk10 7 G2

EvoKit 2x2 P 32L 34W 840 5 Mk10 7 G2

EvoKit 2x2 P 32L 32W 830 1 Mk10 7 G2

EvoKit 2x2 P 32L 34W 830 5 Mk10 7 G2

EvoKit 2x2 P 32L 31W 830 2 0-10 7 G2

20130919

220130919

WARNING

FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN SERIOUS INJURY OR

SIGNIFICANT PROPERTY DAMAGE.

For your protection, carefully read these warnings and instructions in their entirety before installing or maintaining this equipment. These

instructions do not attempt to cover all installation and maintenance situations. If you do not understand these instructions or if additional

information is required, contact your local Philips representative. Retain these instructions for maintenance reference.

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

The EvoKit must be installed and maintained by a professional electrician in accordance with the applicable federal, state and local laws,

regulations and electrical codes, and the installation instructions provided in this document. This professional should be familiar with the

construction and operation of this product and any hazards involved. If not qualiﬁed, do not attempt installation. Contact a qualiﬁed electrician.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR

PERSONAL INJURY

Do not install in a damaged ﬁxture.

Install the EvoKit only in NEMA type G or

Type NFG t-grids with a minimum troer

depth of 3”.

Before installation, turn power o.

WARNING

RISK OF PERSONAL INJURY

This equipment may have sharp edges.

Wear gloves to prevent cuts or abrasions

when removing from carton, handling and

maintaining this equipment.

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

To prevent wiring damage or abrasion, do

not expose wiring to edges of sheet metal

or other sharp objects.

Caution

This kit is designed for permanent

installation in ordinary (Non-Hazardous)

locations in accordance with the National

Electrical Code and all applicable local

codes. Do not use in areas of limited

ventilation or in high ambient enclosures.

Caution

Do not make or alter any open holes

in an enclosure of wiring or electrical

components during kit installation except if

speciﬁcally mentioned in these installation

guide.

Notice

Handle components with care. Do

not drop, slide or scratch any of the

components to prevent visual damage

to the product, loss of functionality or

diculties during installation.

Notice

Do not use abrasive materials, glass cleaners or other solvents on cover plate or lens. To clean

the faceplate, use a mild soap solution.

Do not expose the product to substances and /or materials containing sulphur, chlorine or

other halogen compounds and to chemicals mentioned in below table.

Category Chemical Name

Solvents Toluene, xylene, benzene, chloromethane, chloroform, ethyl

acetate, butyl acetate, acetone, MEK, MIBK

Acid HCl, H2SO4, HNO3

Alkali KOH, NaOH, LiOH, Ca(OH)2

Oil Diesel oil, petroleum, hydro carbons

Host lighting ﬁxture



The Philips EvoKit is designed for installation in a wide variety of 2x4 and 2x2 indoor ﬂuorescent based ﬁxtures in horizontal applications.



• The Philips EvoKit is non-air handling.

• Install the Philips EvoKit only in ﬂuorescent based host lighting ﬁxtures only with a minimum depth of 3”.

• Install the Philips EvoKit only in combination with 15/16” NEMA G or NEMA NFG t-grids.

• Due to the wide variety in troers and ceiling grids, it is recommended that the installer does a test install before commencing a renovation.

• Please verify voltage on the Philips EvoKit product label matches the mains voltage.

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

Luminaire wiring and electrical parts may

be damaged when drilling for installation of

LED retroﬁt kit. Check for enclosed wiring

and components.

320130919

WARNING

RISK OF FIRE, ELECTRIC SHOCK

OR PERSONAL INJURY

Before installation, turn power o.

Installation Philips EvoKit 2x4 and 2x2

Remove host ﬁxture contents

Installation of Side Panels (A)

Set contains Tools required

A Side Panel

B LED Panel

C Troer Label

D Closing Panel

E Diuser

1. Turn power o and take out original cover.

5. Install Side panels (A) in-between troer and

T-grid.

4. Disconnect host ﬁxture ballast from mains.

Notice

Make sure to remove packaging (except the

LED protection*), from EvoKit components

before installing.

Do not install with total power input greater

than power rating of original ﬁxture.

When space in the troer is limited, remove

original ballast.

2. Take out TL tubes.

* Remove LED protection just before installing

the Diuser (E) (see step 14).

3. Remove belly pan. If remaining troer height

is limited, remove ballast.

6. Slide Side Panel (A) outwards as far as

possible.

420130919

Installation Philips Bodine BSL310 (Optional)

Installation LED Panel (B)

Installation Troer Label (C)

Ground connection (Situation 1 - 2)

DO NOT

TOUCH LED

THIS LUMINAIRE HAS BEEN MODIFIED

FROM ITS ORIGINAL CONFIGURATION.

THIS LUMINAIRE WILL NO LONGER ACCEPT THE

ORIGINAL LAMPS STATED ON THE RELAMP LABEL.

CE LUMINAIRE A SUBI DES MODIFICATIONS PAR

RAPPORT À SA CONFIGURATION D’ORIGINE.

CE LUMINAIRE N’ACCEPTERA PLUS LES

AMPOULES PRÉVUES À L’ORIGINE ET REPRISE

SUR L’ÉTIQUETTE RELATIVE AU REMPLACEMENT.

THIS LUMINAIRE HAS BEEN MODIFIED

FROM ITS ORIGINAL CONFIGURATION.

THIS LUMINAIRE WILL NO LONGER ACCEPT THE

ORIGINAL LAMPS STATED ON THE RELAMP LABEL.

CE LUMINAIRE A SUBI DES MODIFICATIONS PAR

RAPPORT À SA CONFIGURATION D’ORIGINE.

CE LUMINAIRE N’ACCEPTERA PLUS LES

AMPOULES PRÉVUES À L’ORIGINE ET REPRISE

SUR L’ÉTIQUETTE RELATIVE AU REMPLACEMENT.

ATTENTION

ESD SENSITIVE

90o

ground

For installation of the Philips Bodine BSL310 Emergency LED Driver, please see the emergency driver installation section from this EvoKit manual

7. Install LED panel (B) in between troer and

T-grid.

9. Place Troer Label (C) inside original troer.

Notice

Make new electrical connections to mains

by employing applicable connectors in

accordance with the applicable federal, state

and local laws, regulations and electrical

codes.

Notice

Do not touch the LEDs with hands or

tooling! Touching LEDs can lead to failure of

the product.

Notice

It is imperative to use the retroﬁt warning

sticker included with the product in order

to alert the end user that this luminaire will

no longer operate on the originally intended

lamps.

WARNING

RISK OF PERSONAL INJURY

Proper grounding of EvoKit metal parts is

required to ensure personal safety.

WARNING

RISK OF PERSONAL INJURY

While installing the LED panel (B) and

Closing Panel (D), make sure the electrical

wiring is not clamped between panels.

8. Fit tab on LED Panel (B) through slot hole on

Side Panel.

Fixate panels and establish ground by turning

each fastener 90 degrees.

10a. Situation 1 Grounding:

Screw grounding cable from Led Panel (B)

to original troer if host ﬁxture ground

connection is made trough host ﬁxture.

10b. Situation 2 Grounding:

Connect to the incoming ground lead

from conduit.

520130919

Mains connection

mains

11. Connect main cables and hide connected

wires behind LED Panel (B).

Installation Closing Panel (D)

Installation Diuser (E)Remove LED protection

LED PROTECTION

90o

12. Install Closing Panel (D) in-between troer

and T-grid.

15. Slide Diuser (E) under the tabs on one side

from either Panel and press diuser (E) over

the tabs on opposite panel.

14. Tear o LED protection.

13. Fixate panels and establish ground by

turning each fastener 90 degrees.

Connection 0-10V and MK10 dimmer (Optional)

DIM+ Class 1 Wiring

or Class 2 Circuit

0-10VDC

DIM-

EvoKit 0-10V wiring diagram

0-10V

}120V / 277V

Dimmer

LINE 2

NEUTRAL

EvoKit MK10 wiring diagram

MK 10

16a. Optional: For connection EvoKit 0-10V

input, use indicated connections on the

driver.

16b Optional: For connection a dimmer to the

EvoKit Mark 10, use indicated connections

on the driver.

Notice

Use 18 AWG Solid Copper Wire

Rated>=300V. Strip Wire 3/8”

In case the EvoKit MK10 277V is installed in

combination with a dimmer, use a minimum

of 2 EvoKits MK10 277V per dimmer.

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

While installing the LED panel (B) and

Closing Panel (D), make sure the electrical

wiring is not clamped between panels.

620130919

Initial installation Philips Bodine BSL310 Emergency LED driver (Sold separately)

violet

brown

15 mm

max.

1. Secure BSL310 (X) to the back side of LED

Panel (B) using two screws (W).

Components: Screws (W), Emergency LED

driver (X), Test switch (Y) Wiring harnass (Z).

3. Install the test switch by feeding the violet

and brown wires through this 1/2” hole and

hand tighten the plastic nut included with the

test switch/LED combo. Add connect from

test switch to wiring harnass (Z) (violet -

violet, brown - brown).

2. Drill 1/2” hole in the LED Panel (B) for

installation of LED/test switch on indicated

area.

Notice

Ensure an un-switched hot circuit is available

to the ﬁxture. This is required for proper

emergency ﬁxture operation.

If the Philips Bodine BSL310 Emergency LED Driver is to be installed into the EvoKit retroﬁt ﬁxture, please follow these instructions and the

instructions provided with the Emergency driver.

WARNING

RISK OF PERSONAL INJURY

Ensure all warning and cautionary markings

given in the Philips Bodine BSL310 installation

instructions are heeded.

blue

BSL310

red/white

yellow /

black red/white

blue/white

yellow

black

white

4. Disconnect the red/white single wire from

the EvoKit driver. Replace it with the blue

output wire from the BSL310 (Z). Place a

wire nut over the original red/white wire for

proper isolation.

5. Connect the yellow output wire from the

BSL310 to the EvoKit blue/white wire

connection block and the yellow/black

output wire from the BSL310 (Z) to the

EvoKit red/white wire connection block.

6. Disconnect black wire and insert white/black

wire (Z) in the EvoKit driver.

AC DRIVER

Emergency

LED

Driver

LOAD

SELECT

JUMPER

WIRE

RED

WHT/RED

BLACK

HOT

COMMON WHITE

BLACK

WHITE

WHT/BLK

WALL SWITCH

CONVERTER

CONNECTOR

7. Connect WHT/RED, BLACK and WHITE

(2x) wires (Z) as per the BSL310 wiring

diagram.

Connect the BSL310 red to red as indicated

in schematic (Z).

A Division of Philips Electronics North

America Corporation.

Printed in USA 8/13

www.philips.com

Philips Lighting

281 Hilmont Road

Markham, Ontario

Canada, L6C 253

1-800-555-0050

A Division of Philips Electronics Ltd.

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

1-800-555-0050

Notice

For the EVOkit, do not connect the jumper

wire / load select (yellow/red) on BSL310.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Leuchte Handbücher

Philips

Philips PTS7-1 Bedienungsanleitung

Philips

Philips 1050SQ_3D Bedienungsanleitung

Philips

Philips SmartBright Dual Select Waterproof Benutzerhandbuch

Philips

Philips ProSpec 37B70E Bedienungsanleitung

Philips

Philips Lytespan 8313 Bedienungsanleitung

Philips

Philips eW Burst Powercore Bedienungsanleitung

Philips

Philips P-5933 Bedienungsanleitung

Philips

Philips Selecon SPX series Bedienungsanleitung

Philips

Philips HF3470/01 Bedienungsanleitung

Philips

Philips 6912528PH Handbuch

Philips

Philips ProSpec 37240 Bedienungsanleitung

Philips

Philips EG1-7 Bedienungsanleitung

Philips

Philips Lytespan 24MHT4RF Bedienungsanleitung

Philips

Philips 69112-31-PH Bedienungsanleitung

Philips

Philips VL72 Bedienungsanleitung

Philips

Philips 17434/**/P7 Series Bedienungsanleitung

Philips

Philips selecon plcyc1 MKII Bedienungsanleitung

Philips

Philips 69141-53-PH Bedienungsanleitung

Philips

Philips 69130-87-PH Bedienungsanleitung

Philips

Philips hue Bedienungsanleitung

Philips

Philips D04 Bedienungsanleitung

Philips

Philips Calculite 8044 Bedienungsanleitung

Philips

Philips Lytecaster 313X Bedienungsanleitung

Philips

Philips Arcitone 336053196 Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung

ArtFox

ArtFox Beam 15R extreme Bedienungsanleitung