Philips Bodine Cold-Pak B4CF1 Bedienungsanleitung
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
SAVE THESE INSTRUCTIONS
THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
© Philips Emergency Lighting
236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-853-5009 • www.philips.com/bodine
70009410
EMERGENCY LIGHTING EQUIPMENT
Installation Instructions
1. To prevent high voltage from being present on red, yellow & yellow/black output leads prior to installation,
inverter connector must be open. Do not join inverter connector until installation is complete and AC power
is supplied to the emergency ballast.
2. This product is for use with one 13 W through 42 W (4-pin) compact fluorescent lamp without integral starters.
3. Make sure all connections are in accordance with the National Electrical Code, Canadian Electrical Code and
any local regulations.
4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter
connector of the emergency ballast before servicing.
5. This emergency ballast is for factory or field installation inside or on top of the fixture.
6. This product is suitable for damp locations where the ambient temperature is -20°C minimum, +55°C
maximum. Product is also suitable for installation in sealed and gasketed fixtures. Product is not suitable
for heated air outlets and wet or hazardous locations.
7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).
8. Do not install near gas or electric heaters.
9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field replaceable.
Contact the manufacturer for information on service.
10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
11. Do not use this product for other than intended use.
12. Servicing should be performed by qualified service personnel.
CAUTION: Verify that all replacement lamp types marked on the installed luminaire are also identified as suitable for
use with this inverter/charger pack.
06/19/17
B4CF1 Cold-Pak
Ni - Cd
INSTALLATION
WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED, YELLOW & YELLOW/
BLACK OUTPUT LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN.
DO NOT JOIN INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS
SUPPLIED TO THE EMERGENCY BALLAST.
NOTE: Make sure that the necessary branch circuit wiring is available. An unswitched
source of power is required. The emergency ballast must be fed from the same
branch circuit as the AC ballast.
STEP #1 INSTALLING THE EMERGENCY BALLAST
> Disconnect AC power from the fixture.
> Refer to illustrations below to install emergency ballast. Note: These are only examples of possible installations.
STEP #2 INSTALLING THE TEST SWITCH
> Drill a 1/2" hole and install the test switch (e.g. through
the side of a surface mounted fixture).
> Refer to the illustrations below and wire the test switch so
that it removes AC power from both the emergency ballast
and the AC ballast at the same time.
* For installation on top of the fixture, wire bundle covers (RMC-60) may be required by state or local codes. These covers are available
from the manufacturer as an accessory kit and must be ordered separately. Call your local distributor or the factory for complete
information.
Inside Ballast Channel
INSIDE BALLAST CHANNEL INSIDE THE FIXTURE Inside Strip Fixture
ON TOP OF FIXTURE
UNSWITCHED FIXTURE
SWITCHED FIXTURE
BLACK
WHITE
HOT
COM
TEST
SWITCH
WALL
SWITCH
AC
BALLAST
BLACK
EMERGENCY
BALLAST
WHITE
WHT/BLK
HOT
COM
TEST
SWITCH
AC
BALLAST
WHT/RED
WHITE
BLACK 120V
OR
ORANGE 277V
EMERGENCY
BALLAST
WHT/BLK
WHT/RED
WHITE
BLACK 120V
OR
ORANGE 277V
Fixture
Test Button
Hex Nut
Hex Nut
Test Switch
Leads
Push to Test
2
When AC power is applied, the charging indicator light is illuminated, indicating that the battery is being charged. When
power fails, the emergency ballast automatically switches to emergency power (internal battery), operating one lamp at
reduced illumination. This emergency ballast will operate one 13 W through 42 W lamp for a minimum of 90 minutes. When
AC power is restored, the normal ballast operation is delayed by approximately three (3) seconds to prevent false tripping
of AC ballast (end-of-lamp-life) shutdown circuit. The temperature control circuitry assures the proper charging current and
battery protection under the full allowable ambient temperature range.
Although no routine maintenance is required to keep the emergency ballast functional, it should be checked periodically to
ensure that it is working. The following schedule is recommended:
1. Visually inspect the charging indicator light monthly. It should be illuminated.
2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. One lamp should
operate at reduced illumination.
3. Conduct a 90-minute discharge test once a year. One lamp should operate at reduced illumination for at least
90 minutes.
! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !
OPERATION
STEP #4 WIRING THE EMERGENCY BALLAST
> Determine the type of AC ballast installed in the fixture.
> Select the appropriate wiring diagram on back to connect the emergency ballast to the AC ballast and lamp(s).
Make electrical connections in accordance with the National Electrical Code, Canadian Electrical Code and any local
regulations.
> After installation is complete, supply AC power to the emergency ballast and join the inverter connector.
> At this point, power should be connected to both the AC ballast and the emergency ballast, and the Charging
Indicator Light should illuminate indicating the battery is charging.
> A short-term discharge test may be conducted after the emergency ballast has been charging for one hour. Charge
for 24 hours before conducting a long-term discharge test. Refer to OPERATION.
> In a readily visible location, attach the label "CAUTION - This Unit Has More Than One Power Connection Point.
To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency
Power Supplies Before Servicing."
MAINTENANCE
STEP #3 INSTALLING THE CHARGING INDICATOR LIGHT
> Install the CHARGING INDICATOR LIGHT as shown in the illustration below so that it will be visible after the
fixture is installed.
NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label.
Charging
Indicator
Light
1/2" White
Bushing
Violet (+)
Brown (–)
Violet (+)
Brown (–)
1/2" White
Bushing
5/8" Black
Bushing
5/8" Black
Bushing
1/2" Punch
Fixture Fixture
Charging
Indicator
Light
3
FIG G. ONE (1) 4-PIN COMPACT LAMP RAPID START BALLAST
WIRING DIAGRAM for Emergency-Only fixtures
WIRING DIAGRAMS for 1-LAMP emergency operation
EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.
IMPORTANT: REFER TO TABLE 1 REGARDING BROWN CONNECTOR
RAPID START AC BALLASTS
1 LAMP
RAPID START
BALLAST
BLUE
BLUE
BROWN
BROWN
RED
YELLOW
YEL/BLK
BLU/WHT
BLUE
RED
RED
LAMP 1
WARNING: Refer to Table 1 before connecting
E
M
E
R
G
E
N
C
Y
B
A
L
L
A
S
T
BLACK
WHITE
BLK
TEST
SWITCH
COM BLK
WHT/BLK
WHITE
WALL SWITCH
WHT/RED
RED
WHITE
VIOLET (+)
BROWN (-)
(CAP UNUSED LEAD) BLACK 120V
OR
ORANGE 277V
INVERTER
CONNECTOR
CHARGING
INDICATOR
HOT
FIG H. TWO (2) 4-PIN COMPACT LAMP RAPID START BALLAST
2 LAMP
RAPID START
BALLAST
BLUE
BLUE
BROWN
BROWN
RED
YELLOW
YEL/BLK
BLU/WHT
BLUE
YELLOW
YELLOW
RED
RED
LAMP 1
LAMP 2
WARNING: Refer to Table 1 before connecting
EMERGENCY
E
M
E
R
G
E
N
C
Y
B
A
L
L
A
S
T
BLACK
WHITE
BLK
TEST
SWITCH
COM BLK
WHT/BLK
WHITE
WALL SWITCH
WHT/RED
RED
WHITE
VIOLET (+)
BROWN (-)
(CAP UNUSED LEAD) BLACK 120V
OR
ORANGE 277V
INVERTER
CONNECTOR
CHARGING
INDICATOR
HOT
FIG I. ONE (1) 4-PIN COMPACT LAMP WITHOUT AC BALLAST(13 W-42 W)
E
M
E
R
G
E
N
C
Y
B
A
L
L
A
S
T
BROWN
BROWN
RED
YELLOW
YEL/BLK
BLU/WHT
BLUE
(CAP)
(CAP)
LAMP
WHT/RED
RED
WHITE
VIOLET (+)
BROWN (-)
WHITE
WHT/BLK
COMMON
HOT
(CAP UNUSED LEAD)
(CAP)
(CAP)
BLACK 120V
OR
ORANGE 277V
TEST
SWITCH
INVERTER
CONNECTOR
CHARGING
INDICATOR
B
L
K
B
L
K
WARNING: Refer to Table 1 before connecting
TABLE 1
LAMP
POWER
BROWN
CONNECTOR
13 - 23 W CLOSED
24 - 42 W OPEN
4
Inhaltsverzeichnis
Andere Philips Beleuchtungsausrüstung Handbücher
Philips
Philips Leko Lite 11430C Fehlerbehebungshandbuch
Philips
Philips 56494-31-16 Bedienungsanleitung
Philips
Philips HUE GO Bedienungsanleitung
Philips
Philips ColorGraze IntelliHue Powercore BCS559 30x60 RGBMW... Bedienungsanleitung
Philips
Philips SM500T Bedienungsanleitung
Philips
Philips EasySmart InstantFit t8 Bedienungsanleitung
Philips
Philips Lightstrip Plus 71901/U8 Series Bedienungsanleitung
Philips
Philips hue Centris Bedienungsanleitung
Philips
Philips 910503700745 Bedienungsanleitung
Philips
Philips RC095V Bedienungsanleitung
Philips
Philips Hadco BUL16 MICRO BULLYTE Bedienungsanleitung
Philips
Philips HF3651 Bedienungsanleitung
Philips
Philips SL BAR 660 Bedienungsanleitung
Philips
Philips bodine LP400 Bedienungsanleitung
Philips
Philips 56454-17-16 Bedienungsanleitung
Philips
Philips Day-Brite Bedienungsanleitung
Philips
Philips LP600STU Bedienungsanleitung
Philips
Philips Selecon Bedienungsanleitung
Philips
Philips ColorBlast TRX Bedienungsanleitung
Philips
Philips HF3671/01 Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
