Philips SQM5572/27 Bedienungsanleitung

www.philips.com/welcome

SQM5572/27

EN Full motion wall mount 3

FR Support mural inclinable dans tous les sens 10

ES Soporte de pared móvil 17

Table of contents

1 Important 3

2 Your full motion wall mount 3

2.1 What’s in the box 4

2.2 What you’ll also need 4

3 Installing your wall mount 5

3.1 Mounting the wall plate (drywall) 5

3.2 Mounting the wall plate (concrete) 5

3.3 Attaching the arms to the display 6

4 Mounting and adjusting 7

5 Guarantee and service 8

1 Important

Take time to read this manual before you

use your wall mount. It contains important

information and notes regarding operating your

wall mount.

part is prohibited without the written consent of

the copyright owner.Trademarks are the

property of Koninklijke Philips Electronics N.V.

or their respective owners.

BWarnings

• Make sure these instructions are read

and thoroughly understood before

attempting installation. If you are

unsure of any part of this installation,

contact a professional installer for

assistance or contact Customer Service

at 1-919-573-7854.

• This product has been designed

for application on a vertical wall in

commercial and residential buildings,

constructed of wood wall studs or

masonry (solid concrete, brick, and

stone). If you are unsure of your wall

composition or for assistance with other

surfaces, contact a qualied installer.

• This product is not designed for use on

walls constructed of metal studs. If you

are unsure of your wall composition

or for assistance with other surfaces,

contact a qualied installer.

• The wall or mounting surface must be

capable of supporting the combined

weight of the mount and the display;

otherwise the structure must

be reinforced.

• Do not exceed the maximum load

capacity of 200lbs for this product.

• Safety gear and proper tools must

be used. Failure to do so can result in

property damage and/or serious injury.

• A minimum of two people are required

for this installation. Do not attempt

to install this mount alone under any

circumstance.

• Follow all instructions and

recommendations regarding adequate

ventilation and suitable locations for

mounting your display. Consult the

owner’s manual for your display for

more information.

2 Your full motion wall mount

Congratulations on your purchase and welcome

to Philips!

To fully benet from the support that Philips

offers, register your product at

www.philips.com/welcome.

Designed to t most brands of TV with a focus

on safety and ease of use.

Includes Easy 1-2-3 installation kit, complete

with: all necessary hardware for mounting on

different types of walls, mounting templates,

stud nder and bubble level.

C- UL US Listed for weight capacity

up to 198lbs.

2.1 What’s in the box.

Wall mount Stud nder Cotter pin (S) S4 Allen Key (x1)

Bag #1 (A) M4x12 Bolt (x4) (B) M4x30 Bolt (x4) (C) M4 Lock Washer (x4)

Bag #2 (D) M5x12 Bolt (x4) (E) M5x30 Bolt (x4) (F) M5 Lock Washer (x4)

Bag #3 (G) M6x12 Bolt (x4) (H) M6x35 Bolt (x4) (I) M6 Lock Washer (x4)

Bag #4 (J) M8x16 Bolt (x4) (K) M8x40 Bolt (x4) (L) M8 Lock Washer (x4)

Bag #5 (M) Small Spacer (x4) (N) Large Spacer (x4) (O) M6 Washer (x4)

Bag #6 (P) Concrete Anchor (x4) (Q) M8x63 Lag Bolt (x4) (R) Lag Bolt Washer (x4)

2.2 What you’ll also need.

• Phillips head screw driver

• Ratchet or driver with 7 mm socket

• Electric drill

• 1/4" (6 mm) drill bit for drywall installation

• 12 mm masonry bit for concrete installation

3 Installing your wall mount

In this chapter, the basic steps to get you started

are described.

B Warning

Carefully read the safety precautions in

“Section 1 Important” before you install

the wall mount.

3.1 Mounting the wall plate (drywall)

B Warning

For safety reasons, this mount must be

secured to two adjacent wood studs at

least 16" apart.The studs must be capable

of supporting the combined weight of the

mount and display.

1See enclosed mounting template for

diagram and guide of how to mount

properly on the wall.

2 Using a stud nder, locate and mark two

adjacent studs for securing the mount

(make sure your marks are in the center

of each stud).You can use your own stud

nder or the one included in the

hardware kit.

D Note

Once studs have been located you will

need to verify with a hammer and a nail

A) Simply place the nail over your mark

on the wall and tap in with hammer.

If the nail encounters resistance and is

secure in wall you have veried a

stud location.

B) If the nail just pushes through with no

resistance you will need to start over

and locate the stud.

3Using the enclosed mounting template,

place the diagram against the wall and mark

four locations (two per stud) on the wall

where the mount is to be installed. Be sure

to use the center of each stud.

4With the help of another person, place the

mount against the wall and level it using the

bubble guide.

5While another person holds the mount in

place, mark four locations (two per stud)

on the wall where the mount is to be

installed. Be sure to use the center of each

stud. (these marks should line up with the

ones made in step 3 above using

the template).

6Set the mount aside and drill a 1/4" (6 mm)

pilot hole at each marked location.

7Place the mount back against the wall and

secure it using the lag bolts (Q) and lag bolt

washers (R) provided. Do not over-tighten

these bolts and do not release the mount

until all bolts are in place.

8Once all (4) lag bolts are in place you must

tighten each one. (note: be sure not to over

tighten). 1

3.2 Mounting the wall plate (concrete)

B Warning

For safety reasons,the concrete wall must be

capable of supporting the combined weight of

the mount and display.

1See enclosed mounting template for

diagram and use enclosed mounting

template as a guide for precision mounting.

2Using the enclosed mounting template,

place the diagram against the wall and mark

four locations on the wall where the mount

is to be Installed.

3With the help of another person, place the

mount against the wall and level it using the

bubble guide.

4While another person holds the mount

in place, mark four locations on the wall

where the mount is to be installed.

5Set the mount aside and drill a 12mm pilot

hole at each marked location. Remove any

excess dust from the holes.

6Insert a Concrete Anchor (P) into each

hole so that it is ush with the concrete

surface.A hammer can be used to lightly

tap the anchors into place if necessary.

7Place the mount back against the wall and

secure it using the lag bolts (Q) and lag bolt

washers (R) provided. Do not over-tighten

these bolts and do not release the mount

until all bolts are in place.

8Once all (4) lag bolts are in place you

must tighten each one. Be sure not to

over tighten. 2

D Note

If the concrete wall is covered by a layer

of plaster or drywall, the concrete anchor

must pass completely through the layer to

rest ush with the concrete surface.

3.3 Attaching the arms to the display

B Warning

Use extra care during this part of the

installation. If possible, avoid placing your

display facedown as it may damage the

viewing surface.

D Note

Your mount comes with a selection of bolt

diameters and lengths to accommodate a

wide variety of display models. Not all of

the hardware in the kit will be used.

1Determine the correct length of bolt to

use with your display by rst examining the

back of your display.

A. If your display has a flat back:You will

use one of the shorter bolts (A, D, G, or J)

from the hardware kit. 3

B. If your display has a curved or

recessed back: You will use one of the

longer bolts (B, E, H, or K) along with a

spacer (M or N). 4

2Determine the correct diameter of bolt to

use by carefully trying one bolt each from

Bags 1 - 4 of the hardware kit. Do not force

any of the bolts – if you feel resistance stop

immediately and try a smaller diameter bolt.

3Attach the arms to the back of your display

using the bolts identified in Steps 1 and 2

along with the corresponding Lock Washer

(C, F, I, or L). 5

A) If you are using the M4, M5, or M6 bolts

(Bags 1, 2, and 3 respectively), you will also

need to use the M6 Washers (O).

B) If you are using one of the longer bolts on

a display with a curved or recessed back,

you will also use a spacer (M or N). Use the

smaller spacer (M) for M4 and M5 bolts and

the large spacer (N) for M6 and M8 bolts.

4Make sure all screws are secure, but do not

over-tighten them.

E Tip

Use a longer bolt and spacer for displays

with curved or recessed backs. Do not use

the M6 Washer (O) if you are using the M8

Bolts (J or K).

4 Mounting and adjusting

1With the help of another person, carefully

lift your display and place it on mount.

Place the display in the middle of the

mount, and do not release the display until

the mounting arms have securely hooked

onto the crossbars. 6

2Move the safety tab located on each arm

into position to avoid having the display

accidentally lifted from the mount.This

MUST be done in order to secure the

display to the mount.

D Note

A cotter pin (included) is used to secure

the arm into position OR a padlock

(not included) can be inserted into one

of the tabs to help prevent theft of

your display. 7

3The cable management clips can be used

to keep your power cord and other cables

in order.

4Side-to-side and front-to-back adjustments

can be made by firmly grasping your display

and carefully moving it to the desired

position.

5If any of the arms become too lose to hold

their position, they can be tightened using the

alley key provided in your hardware kit. 8

6To adjust the tilt position of your display,

have one person hold the display in place while

another person loosens the two tilt adjustment

knobs located on either side of the mount.

Once the knobs are loose, move the display to

the desired angle.Tighten the knobs securely

before releasing the display. 9

7If you find that your display is not level, first

loosen the horizontal adjustment screws located

behind the mount using the allen key provided

in your hardware kit. Carefully level your display

and re-tighten the adjustment screws once you

are satisfied. 10

5 Guarantee and service

Please contact Philips directly if you have any

questions in the installation process of the wall

mount. Call 1-919-573-7854.

Limited Two-Year Warranty

Philips warrants that this product shall be free

from defects in material, workmanship and

assembly, under normal use, in accordance with

the specications and warnings, for two years

from the date of your purchase of this product.

This warranty extends only to the original

purchaser of the product, and is not transferable.

To exercise your rights under this warranty, you

must provide proof of purchase in the form of

an original sales receipt that shows the product

name and the date of purchase. For customer

support or to obtain warranty service, please

call 919-573-7854.THERE ARE NO OTHER

EXPRESS OR IMPLIED WARRANTIES. Philips’

liability is limited to repair or, at its sole option,

replacement of the product. Incidental, special

and consequential damages are disclaimed where

permitted by law.This warranty gives you specic

legal rights.You may also have other rights that

vary from state to state.

www.philips.com/welcome.

Table des matières

1 Consignes de sécurité importantes 10

2 Votre support mural inclinable

dans tous les sens 10

2.1 Contenu de la boîte 11

2.2 Outils requis 11

3 Installation du support mural 12

3.1 Installation de la plaque murale sur

un mur de gypse 12

3.2 Installation de la plaque murale sur

un mur de béton 12

3.3 Fixation des bras sur le téléviseur 13

4 Montage et réglage 14

5 Garantie et service 15

1 Consignes de sécurité

importantes

Lisez ce manuel attentivement avant d’utiliser

votre support mural. Il contient des informations

importantes concernant l’installation et

l’utilisation du support.

totalité ou d’une partie du présent manuel est

interdite sans l’autorisation écrite du titulaire du

droit d’auteur. Les marques de commerce sont la

propriété de Koninklijke Philips Electronics N.V.

ou de leur détenteur respectif.

BAvertissements

• Assurez-vous de bien comprendre

les instructions avant d’installer le

support mural. Si vous n’êtes pas

certain de bien comprendre une étape,

consultez un installateur professionnel

ou communiquez avec le service à la

clientèle, au 1 (919) 573-7854.

• Le support mural est conçu pour

être xé sur les murs d’immeubles

commerciaux ou résidentiels ayant une

ossature en bois, en béton, en briques

ou en pierres. Si vous n’êtes pas certain

de la composition du mur ou si vous

voulez installer le support mural sur une

autre surface, consultez un installateur

professionnel.

• Le support mural n’est pas conçu

pour être xé aux murs de gypse dont

la structure est faite de montants

métalliques. Si vous n’êtes pas certain

de la composition du mur ou si vous

voulez installer le support mural sur une

autre surface, consultez un installateur

professionnel.

• Le mur ou la surface porteuse choisie

doit pouvoir supporter le poids combiné

du support et du téléviseur, sinon,

la structure doit être renforcée.

• Ne dépassez pas la capacité de charge

maximum du produit, soit 90,72 kg

(200 lb).

• Pour réduire les risques de dommages

matériels et de blessure, portez

l’équipement de sécurité nécessaire et

utilisez les outils appropriés.

• L’installation doit être effectuée par au

moins deux personnes. N’essayez en

aucun cas d’installer le support mural

sans l’aide d’une autre personne.

• Suivez toutes les instructions et

recommandations concernant le

dégagement autour du téléviseur et

l’emplacement choisi pour le support

mural. Pour en savoir davantage,

consultez la documentation du

téléviseur.

2 Votre support mural

inclinable dans tous les sens

Félicitations pour votre achat et bienvenue dans

le monde Philips!

Pour bénécier pleinement de l’assistance

offerte par Philips, enregistrez votre produit sur

le site www.philips.com/welcome.

Conçu pour s’adapter à la plupart des marques

de téléviseur, en gardant à l’esprit la sécurité et

la facilité d’utilisation.

Comprend une trousse d’installation en trois

étapes faciles avec tout le matériel nécessaire

pour xer le support sur différents types de

murs, des gabarits de montage, un détecteur de

montant et un niveau à bulle.

Homologué C-UL pour un poids maximal de

90 kg (198 lb).

Inhaltsverzeichnis

Sprachen:

Andere Philips Rack & Stand Handbücher

Philips

Philips IntelliVue Arm Bedienungsanleitung

Philips

Philips Brisa FB3114E_3d Bedienungsanleitung

Philips

Philips STS1000/00 Bedienungsanleitung

Philips

Philips IntelliVue MP2 Bedienungsanleitung

Philips

Philips Brilliance 151AX Bedienungsanleitung

Philips

Philips STS8001/00 Bedienungsanleitung

Philips

Philips Easy Bracket STS1000/00 Bedienungsanleitung

Philips

Philips RAR-MAR36 Bedienungsanleitung

Philips

Philips SQM7441 Bedienungsanleitung

Philips

Philips Efficia Rack Bedienerhandbuch

Philips

Philips STS8001 Bedienungsanleitung

Philips

Philips TC27PV2 Bedienungsanleitung

Philips

Philips 9890 010 83921 Bedienungsanleitung

Philips

Philips SQM7842 Bedienungsanleitung

Philips

Philips STS1300 Bedienungsanleitung

Philips

Philips SB7G19S/00 Bedienungsanleitung

Philips

Philips 60PL9200D Bedienungsanleitung

Philips

Philips 22AV3200 Bedienungsanleitung

Philips

Philips 22AV3200 Bedienungsanleitung

Philips

Philips HeartStart MRx Bedienungsanleitung

Philips

Philips SB7S17S/00 Bedienungsanleitung

Philips

Philips SDW1410 Bedienungsanleitung

Philips

Philips STS8007 Bedienungsanleitung

Philips

Philips SB7G17S/00 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung