Philips KWR101830/01B Bedienungsanleitung

Philips Home Control

Confidential ©Philips Home Control,

2013

Page 1 of 14

Manual of KWR101830/01B, KWR101830/01BS &

KWR101830BU

Philips Home Control

Confidential ©Philips Home Control,

2013

Page 2 of 14

FCC Statement

FCC Part 15.19

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

No special accessory is required to enable the equipment to comply with the emission

limits.

KWR101830/01B Manual (Draft Version)

Status :Draft, For Review Page 3 of 14

Philips Proprietary &Confidential

Philips Home Control Company Restricted

1. Product Description

1.1 Product Features

•Dual button entry RC and KWR.

•Number of keys: 38 for KEYBOARD, 18 for RC. Total 56 keys.

•4 main functions: Remote Control, Mouse Cursor Control, Qwerty KEYBOARD for text entry and

downstream data transfer.

•128k Flash for handling RF functions.

•6 axis motion pointing.

•IR Learn using Data Flash.

•IR Database.

•IR uses Flash chip.

•Low voltage alert through LED blinks.

•Works with USB Receiver dongle OVU810006.

KWR101830/01B Manual (Draft Version)

Status :Draft, For Review Page 4 of 14

Philips Proprietary &Confidential

Philips Home Control Company Restricted

1.2 Product

Picture for illustration onl

KWR101830/01B Manual (Draft Version)

Status :Draft, For Review Page 5 of 14

Philips Proprietary &Confidential

Philips Home Control Company Restricted

2. RF Functions

2.1 RF Pairing

1) Make sure RC is within 1m distance from the STB and no other RF RCs are present.

2) Make sure the Qwerty keyboard faces upwards.

3) Press and hold Keyboard W and Keyboard O keys together for at least 5 seconds.

4) The KEYBOARD LED will start blinking, and RC is now in pairing mode.

5) Activate pairing mode on STB (STB sends activate command or reset dongle power).

6) Once the pairing is successful, the KEYBOARD LED will be turned off; otherwise, the KEYBOARD

LED will stay lit till timeout.

There will be a 30 seconds timeout for RC to be in pairing mode. Previously paired receiver shall be

retained as long as the STB did not initiate the pairing. See Note below on different pairing scenarios.

User can start from Step 1 again if pairing failed.

Note:

When a previously paired RC starts pairing with

1. Different receiver

o Only upon successful pairing, the RC shall replace the previously paired receiver with the new

receiver.

o If the pairing process fails or pairing timeout occurs, the previously paired receiver will be retained.

2. Same receiver

o Previously paired information of the same receiver shall first be erased from the RC before pairing

process starts.

o If the pairing process fails or pairing timeout occurs, the previously paired receiver will not be

retained.

At any one time,

 Only one RC is allowed to be in pairing mode, i.e. no concurrent pairing is allowed.

 Each RC can only work with one receiver, i.e. 1-to-1 pairing.

2.2 RF Un-Pairing

The following steps for un-pairing:

1) Make sure the Qwerty keyboard faces upwards.

2) Press and hold Keyboard X and Keyboard UP keys together for at least 5 seconds.

3) The KEYBOARD LED will start blinking slowly after 5 seconds.

4) Reset the power or battery and the RC is ready to pair again.

2.3 Remote Idling, RF Link Timeout with connection

When detected no activity, the RC will enter SLEEP mode. During SLEEP mode, RF link will be

disconnected to preserve power. Pressing any key or any gesture action will resume the RC to

ACTIVE mode almost immediately. The key-press that resumes the RC from SLEEP mode will be

remembered and transmitted.

When the RC wakes up from SLEEP mode, there may be reconnection latency depending on the RF

link condition with the receivers.

Once the RF (2.4G) link has been established, the RC will execute upon ANY key-press. Key presses

prior to successful RF link connection will not be transmitted.

KWR101830/01B Manual (Draft Version)

Status :Draft, For Review Page 6 of 14

Philips Proprietary &Confidential

Philips Home Control Company Restricted

2.4 RF Broken Link

RF link is broken when the RF (2.4G) connection is lost or when the receivers sleep or during system

shutdown states (S3, S4 or S5) or due to out-of-range.

2.5 RF ACTIVE / SLEEP

From RF ACTIVE >> SLEEP User action Remote Control action

No key-press for less than 15 seconds. RF goes to SLEEP. In SLEEP mode, all LEDs are OFF.

No motion senses for about 15 seconds. RF goes to SLEEP. In SLEEP mode, all LEDs are OFF.

2.6 RF Auto Connection

When the RC wakes up or resumes from SLEEP mode or come back within range of a powered-on

paired receiver, the RF link will be reconnected automatically. No RF re-pairing is needed.

2.7 RF Out-of-Range

When the RF link is broken or out-of-range and is stationary, the RC goes to SLEEP immediately to

conserve power.

KWR101830/01B Manual (Draft Version)

Status :Draft, For Review Page 7 of 14

Philips Proprietary &Confidential

Philips Home Control Company Restricted

3. Operational Features

3.1 Mode Switch

3.1.1 RC to Keyboard

When in RC mode, KEYBOARD keys will be locked to prevent accidental presses. KEYBOARD keys

can only be unlocked by tilting 90 degrees clockwise or anticlockwise. Once tilted more than 90

degrees, mouse cursor will stop moving if it is in Mouse mode.

If KEYBOARD keys are faced up upon power up, a command will be sent from the RC.

3.1.2 Keyboard to RC

When in KEYBOARD mode, user can change to RC mode by tilting 90 degrees clockwise or

anticlockwise. When in KEYBOARD mode, RC keys will be locked to prevent accidental presses.

Once tilted more than 90 degrees, mouse cursor will start moving if it is in Mouse mode.

If RC keys are faced up upon power up, a command will be sent from the RC.

3.2 Remote IR Keys

TV POWER, VOL+, VOL-, MUTE and AV are IR command keys. With RC side faced up and in a

portrait orientation, pressing these buttons will fire the respective IR codes from the IR LED of the

remote control.

3.3 Remote RF keys

Remote RF keys will be sent in the form of HID Keyboard keys.

3.4 Motion Control Mouse Mode

Mouse mode allows user to use the 3-D gyroscope and accelerometer of the RC as a floating mouse

or joystick. In this mode, user is also expected to operate the remote control in free air and not laid

down and operating it in a stationary position.

The relative movement of panning and lifting (roll, yaw and pitch) will control the mouse cursor to

move in the same relative direction on the screen.

For mouse cursor control, toggle motion sensor ON:

- Move remote control in the air to use motion mouse control

- Press OK key will be Mouse Left Click function only, press and hold Mouse Left Click is supported

- Provides RAW data for gesture processing, enable/disable with downstream command from host.

KWR101830/01B Manual (Draft Version)

Status :Draft, For Review Page 8 of 14

Philips Proprietary &Confidential

Philips Home Control Company Restricted

3.4.1 Mouse Mode

Default mode for mouse mode = OFF when first power up or upon a power recycle.

There will be LED indication on TV POWER button on the activation and deactivation of motion

sensor.

Mouse mode will be disabled if user entered programming mode, i.e. IR Learning with mouse mode

ON; user needs to press MOUSE key again if mouse function is needed after exiting programming

mode.

Downstream command from host can also toggle Mouse mode ON/OFF. Both MOUSE (TOGGLE)

key and downstream command have equal priority, hence the last trigger will supersede previous

state.

- Mouse mode code will be sent upon a reset cycle either during power recycle or watchdog reset.

- Mouse mode code will be sent when user pressed the MOUSE key

- Mouse mode code will be sent after each downstream command

- Mouse mode code will be sent after any other feature (e.g. IR Learning mode) that changes Mouse

ON/OFF state.

3.5 Keyboard Mode

The Qwerty keyboard will be held by both hands and used in landscape orientation.

The keyboard also supports secondary keys by using FN, CAPS or Alt Gr; this allows the keyboard

to support uppercase characters, symbols and digits with the limited number of Qwerty keys.

There are 2 ways of activating secondary keys:

1. Press and release FN or CAPS or Alt Gr key followed by pressing another key. For example, press

FN then Q will send „1‟, press CAPS then Q will send „Q‟. After Q is released and pressed again,

„q‟will be sent.

2. Press and hold FN or CAPS or Alt Gr key followed by pressing another key. For example, press

and hold FN and then press Q will send „1‟, press and hold CAPS and then Q will send „Q”.

As long as the secondary key is pressed and held, the secondary character will have the same

repeating behavior as the normal primary key „press and hold‟.

To minimize accidental presses of the Qwerty keys while in RC or Mouse Cursor Control, the Qwerty

keys will be deactivated. When not in SLEEP mode and the keyboard side is detected faced down,

the Qwerty keys will be locked, key presses on the keyboard will be ignored. When device is not in

SLEEP mode and the keyboard side is detected faced up, the Qwerty keys are unlocked.

3.5.1 Other Key Codes

When “ALTGr” + “Space” is pressed, F10 key code will be sent from the RC.

KWR101830/01B Manual (Draft Version)

Status :Draft, For Review Page 9 of 14

Philips Proprietary &Confidential

Philips Home Control Company Restricted

3.6 LED Indicator Behaviour

Total 3 backlit LED indicators:

1) RED colour, on TV POWER key, RC side, indicates all key-press events on RC side except for

Mouse Left Click.

2) RED colour, on SYSTEM POWER key, RC side, for Mouse Left Click only.

3) AMBER colour, on TAB key, KEYBOARD side, indicates all key-press events on KEYBOARD side.

Location Indication purpose Status description

TV POWER Indicates IR and RF code transmission 1 short blink in red each time a valid

key is pressed.

TV POWER Low battery warning 2 long blinks in red each time a RC key

is pressed.

TAB Low battery warning 2 long blinks in amber each time a

KEYBOARD key is pressed.

SYSTEM POWER Mouse Left Click 1 short blink in red each time Mouse

Left Click is pressed.

SYSTEM POWER Definition of Error (in setup mode):

- Key-press and hold ≥30 seconds

- Invalid key-press

- Timeout

3 short blinks.

SYSTEM POWER IR Learn / AutoSearch programming As defined in Section 7.

TAB Shows successful RF pairing Flashes rapidly in amber for 2 s

TAB Key stuck 3 short blinks

TAB Indicates Qwerty KEYBOARD activated 2 blink in amber when KEYBOARD key

is pressed except for:

- ALTGr, CAPS and FN keys (No LED

indication).

KWR101830/01B Manual (Draft Version)

Status :Draft, For Review Page 10 of 14

Philips Proprietary &Confidential

Philips Home Control Company Restricted

4. Infrared Function

The remote control has a default IR code table for 5 TV keys (TV POWER, VOL+, VOL-, MUTE and

AV). These 5 keys also support IR Learning.

4.1 Infrared (IR) Learn

Following are the 5 IR functions keys for IR

Learning: Key Name

Key function

TV POWER TV Power On/Off

VOL+ TV Volume Up

VOL- TV Volume Down

MUTE TV Mute

AV Source selection

Follow the key sequences below to invoke the infrared (IR) Learning feature for a key:

Step IR Learn Sequence

1 Press and hold “VOL+” and “VOL-” Key for 3 seconds. Release the keys, SYSTEM POWER

LED stays on; RC enters IR Learning mode.

2 Press and release a learnable key. The SYSTEM POWER LED indicator will reverse blink once

and TV POWER LED will turn ON.

3 Hold the remote to be learned at an optimum distance (3cm to 6cm); aim directly at DUAL IR

lens and press the key to be learned until SYSTEM POWER LED responds.

4 The SYSTEM POWER LED shall slow blink 2 times if learning is successful and the newly

learned code will replace the previous one.

The SYSTEM POWER LED shall fast blink 3 times if the learning fails. Previously learned code

will be kept. TV POWER LED will turn OFF.

Go back to Step 2 to select learnable key again.

5 User can learn other keys by repeating Steps 2 to 4.

6 Press “BACK” Key in IR Learning mode and will exit to normal mode.

Error handling:

1. If a wrong key is pressed at Step 2, SYSTEM POWER LED will fast blink 3 times and go back

to Step 2.

2. If any stuck key(s) occurs in any of the learning sequence, SYSTEM POWER will fast blink 3

times, exit IR Learning mode and enter Stuck Key mode.

Please take note of the following points when performing infrared (IR) Learning:

1. The remote will NOT exit IR Learning mode, except for the following occurrences:

1. If no key is selected within 30 seconds after entering IR Learning mode.

2. If stuck key timed out.

3. If “BACK” Key is pressed.

2. After pressing and releasing a learnable key and waiting for the signal to be learned:

1. If there is no signal received within 30 seconds, SYSTEM POWER LED shall fast blink 3

times to indicate learning had failed and exits IR Learning mode.

2. If the same key is pressed again (See Section 7.2), SYSTEM POWER LED will slow blink 2

times and wait for a new key-press (go back to Step 2 to select a learnable key again).

3. If any other key is pressed, SYSTEM POWER LED will fast blink 3 times and wait for a new

key-press (go back to Step 2 to select learnable key again).

3. The TV POWER LED will always be ON during IR Learning mode while waiting for a key input

or signal to be learned.

4. When IR learning is in progress, RF functions are disabled (e.g. keys on KEYBOARD side are

locked). Only after exiting from IR Learning mode, the RF functions are resumed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Fernbedienung Handbücher

Philips

Philips SRP2018 Bedienungsanleitung

Philips

Philips SRP5004/87 Bedienungsanleitung

Philips

Philips SRU 740/10 Bedienungsanleitung

Philips

Philips SRP5004/53 Bedienungsanleitung

Philips

Philips SBCRU640 Bedienungsanleitung

Philips

Philips SRU4007/27 Bedienungsanleitung

Philips

Philips SRP1103/27 Bedienungsanleitung

Philips

Philips SBC RU422 Bedienungsanleitung

Philips

Philips SBC RU 510 Bedienungsanleitung

Philips

Philips SRU3030/10 Bedienungsanleitung

Philips

Philips Perfect replacement SRP5107/27 Bedienungsanleitung

Philips

Philips SRU3007/27 Bedienungsanleitung

Philips

Philips SRU4105WM - Universal Remote Control Bedienungsanleitung

Philips

Philips Perfect replacement SRU5107WM Bedienungsanleitung

Philips

Philips SBCRU630/85 Bedienungsanleitung

Philips

Philips 22AV8573/00 Bedienungsanleitung

Philips

Philips SRU 5120/87 Bedienungsanleitung

Philips

Philips SRP1101/10 Bedienungsanleitung

Philips

Philips SRP9348D/27 Bedienungsanleitung

Philips

Philips SBCRU440/00U Bedienungsanleitung

Philips

Philips RC4284504/01RP Bedienungsanleitung

Philips

Philips SRU160NC/05 Bedienungsanleitung

Philips

Philips Magnavox PM520 Bedienungsanleitung

Philips

Philips SRP3013 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung