Philips B200G Bedienungsanleitung

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Company

281 Hillmount Road

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

B200G Industrial Duty Emergency Unit

(With IntelliCharge)

Installation and Operating Instructions

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

All servicing should be performed by qualified personnel only.

Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering by

unauthorized personnel.

The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

Do not use this equipment for other than intended use.

Do not use outdoors.

Do not let supply cords touch hot surfaces.

Do not mount near gas or electric heaters.

Do not mount near open flames or sparks.

The battery supplied with this equipment is a sealed maintenance free lead calcium battery. Do not attempt to

service this battery.

SAVE THESE INSTRUCTIONS

CAUTION: To avoid electrical overload, total connected lamp load (factory and field installed) should not

exceed output rating.

WARNING –Shut off AC power to branch circuits to which units will be connected. All wiring should be per

N.E.C. Articles 501-4(b) and local codes.

To maintain warranty, equipment with batteries must be installed or placed on charge within prescribed period

after shipment.

Page 2 of 7

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Company

281 Hillmount Road

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

Page 3 of 7

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Company

281 Hillmount Road

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

INSTALLATION INSTRUCTIONS

The B200G is intended for surface mounting only and is suitable for 120VAC or 277VAC, 60 Hz operation.

1. Remove keyway knockouts (2) if cabinet is to be mounted to the wall.

2. Remove hole plugs as needed for installing the lamp heads. (Figure 1)

Figure 1

3. Install lamp heads to cover per instructions provided with lamp heads.

4. Connect lamp head leads, one grey lead to one terminal on the lamp head, a white lead to the other

terminal. (Figure 4)

5. Remove appropriate knockout located on sides of cabinet to accept AC service.

6. Mount cabinet directly to wall or use optional mounting plate MBB. (Figure 2)

Figure 2

7. Max Mounting Height: 12W Halogen=7.5 ft., 7W/MR16/LED=30 ft., 15W LED AR111=31ft.

8. Install batteries in battery chamber. DO NOT LIFT BATTERY BY TERMINALS. (Figure 3)

9. Connect Battery leads to the batteries. (Figure 4). Warning: The unit will be damaged if the batteries

are connected improperly.

Page 4 of 7

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Company

281 Hillmount Road

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

10. Hookup AC service to the unit as follows: Caution: Do not connect AC until battery is installed.

OPERATING INSTRUCTIONS

Energize AC power to the unit. The unit will initiate normal power-up sequence (See Normal Power Up

Sequence).

Figure 3

Self-Diagnostic System Operation –Emergency Light or EXIT Sign Products

Normal Power Up Sequence

At power up the red and green LED indicators will alternately flash for one to two seconds. Next the product will execute

a “Power Up Quick Test” causing the green LED indicator to flash rapidly. If any faults are detected during the “Power Up

Quick Test” these will be evident by a flashing red LED indicator. If the audible diagnostic option has been ordered, the

flashing red LED will be accompanied by a simultaneous beeping tone. (Note: A continuous rapid alternating Red/Green

flash with rapid beeping tone indicates 277V applied to 120V input lead. TURN OFF POWER IMMEDIATELY!)

120 VAC OPERATION

277 VAC OPERATION

White Wire

- Common

White Wire

- Common

Black Wire

- 120V Line

Black Wire

- Cap Wire

Blue Wire

- Cap Wire

Blue Wire

- 277V Line

Green Wire

- Ground

Green Wire

- Ground

Page 5 of 7

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Company

281 Hillmount Road

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

Emergency Operation

Emergency operation occurs when AC power fails. The product remains in emergency operation until AC power is

restored or battery capacity is depleted. During emergency operation both red and green LED indicators are disabled.

User Interface

Green LED indicator

Slow Flash/Continuous ON = AC power present; normal operating condition

Rapid Flash = product performing an automatic or manually initiated diagnostic test

Red LED indicator

Single Flash = battery fault

Two Flashes = lamp failure (light bar failure –EXIT signs)

Three Flashes = charger fault

Four Flashes = transfer fault

(If more than one fault condition is present simultaneously, the red LED will flash the indication pattern for each

fault independently then repeat the cycle.)

Pushbutton Test Switch

Long Press (longer than 0.5sec) transfers product to emergency operation during time the button is

pressed.

Short Press initiates self-diagnostic activities as follows:

One Press cancels diagnostic test presently running.

Two Presses starts a one minute diagnostic test.

Three Presses starts a 90 minute diagnostic test.

Four Presses conducts a lamp load calibration (emergency light products only).

Seven Presses initiates a system reset.

(Note: the microprocessor will allow up to seven, one minute diagnostic tests within the first 24 hours of

operation. Allow 24 hours of charging before performing any long duration testing.)

Buzzer (optional) –Sounds in unison with the flashing red LED if a fault condition is present. Buzzer may be

silenced for up to 196 hours by a short press of either the test switch or the optional IR remote control device

“silence” button. Correcting fault condition will cancel fault notification. Lamp failure indication requires a

manually activated diagnostic test after lamp replacement to cancel notification.

Page 6 of 7

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Company

281 Hillmount Road

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

IR Remote Control (optional) - is a hand held device that allows remote activation of diagnostic testing and

silencing of the optional buzzer during fault conditions.

Top View of IR Remote Control

Bottom View of IR Remote Control

Press any button for desired action

To stop a test, press “Cancel”

See label on bottom view for additional information

Page 7 of 7

Philips Lighting Company

200 Franklin Square Drive

Somerset, NJ 08873

Phone: 855-486-2216

www.philips.com/luminaires

Philips Lighting Company

281 Hillmount Road

Markham ON, Canada L6C 2S3

Phone: 800-668-9008

www.philips.com/luminaires

9140052272 June, 2015

Figure 4

Inhaltsverzeichnis

Andere Philips Sicherheitssystem Handbücher

Philips

Philips 26PF9631D Bedienungsanleitung

Philips

Philips ADIM ADM0101 Bedienungsanleitung

Philips

Philips LBB 1370 Bedienungsanleitung

Philips

Philips MathLine 27CE7695 Bedienungsanleitung

Philips

Philips lifeline Bedienungsanleitung

Philips

Philips AutoDome TC700 Series Bedienungsanleitung

Philips

Philips VSS2360/00T Bedienungsanleitung

Philips

Philips In.Sight M100 Bedienungsanleitung

Philips

Philips VSS2364/C4T Bedienungsanleitung

Philips

Philips LDH2544/10 Bedienungsanleitung

Philips

Philips VSS2902 Bedienungsanleitung

Philips

Philips In.Sight M100 Bedienungsanleitung

Philips

Philips Lifeline FD100 Bedienungsanleitung

Philips

Philips FD100SL Bedienungsanleitung

Philips

Philips M100/37 Bedienungsanleitung

Philips

Philips VSS7370/D3T Bedienungsanleitung

Philips

Philips VSS2360/00T Bedienungsanleitung

Philips

Philips VSS7374/D4T Bedienungsanleitung

Philips

Philips LRM3120K/27 Bedienungsanleitung

Philips

Philips HF3506/05 Bedienungsanleitung

Philips

Philips LRM3220D/27 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung