Philips LRM3120K/27 Bedienungsanleitung

Home power

LRM3120K/27

The alarm unit has a low battery circuit.

When the batteries reach a low level,

the indicator light will ash slowly.

Average battery life for typical usage is

up to one year.

LEARN

Home/

away

switch

Alarm/

chime

switch Magnet

Indicator

light

Learn

button

Double-

sided tape

Mounting

plate

Screws

Battery

compartment

Low Battery Indicator

The keypad controlled door alarm

requires three (3) AAA Alkaline

batteries (not included).

To install the batteries:

1. Remove screw from battery

compartment door located

on back of the unit. Slide o the

door in the direction of

the arrow.

2.Insert three (3) AAA batteries

noting the polarity diagram inside

the battery compartment.

3.Replace door and

secure screw.

Installing Batteries

The keypad allows you to set a

personal 4-digit code for arming and

disarming the alarm.

1. Remove screw from battery

compartment door located on

back of the unit. Slide o the door

in the direction of the arrow.

2.Press the LEARN button.

3.The red light on the front of the

alarm will blinkfor 15 seconds.

During this time, input your 4-digit

code. A beep will conrm each

input. The unit will ash a green

light 3 times to conrm the new

4-digit code has been saved.

4.Replace cover and

secure screw.

Creating Your Personal Alarm Code

LEARN

Learn

button

1. Select desired location for

alarm. The alarm is designed to

mount to the door frame or to

the door itself. Use either the

provided screws (for permanent

mounting) or double-sided tape

(for temporary mounting). The

recommended location is the

back of the door, with the magnet

mounted to the door frame.

Mounting the alarm to the door

ensures that the alarm will not be

damaged by opening and closing

the door.

Installation

Recommended Mounting Method Alternate Mounting Method

Note that the magnet may be

mounted to either side of the

alarm as long as the arrows line

up.

IMPORTANT:Whether mounting

to the door or door frame, the gap

distance between the alarm and

magnet must be 1/2” or less.

2.Attach the mounting plate to

the back of the alarm. Peel the

protective covering from one side

of the double-sided tape and then

apply to mounting plate. Remove

protective covering from the back

side of the double-sided tape

and lightly mount the alarm in

the desired position. Make sure

Distance must be less that 1/2”

the surface you are mounting to

is clean and dry. For best results,

clean the mounting surface with a

mixture of 50% isopropyl alcohol

and 50% water.

Do not apply rm pressure until

location is nal.

NOTE: When mounting to a door

frame, the mounting plate mounts

o-center to the left or right in

order to position alarm closest to

the edge of the door.

Double-sided tape

Mounting Plate

Alarm

3.Using double-sided tape, lightly

attach the magnet to the opposite

edge next to the alarm. Line up

the arrows of the alarm and the

magnet. Ensure the distance

between the two pieces is 1/2”

or less. To test the gap distance,

slide the ALARM/CHIME switch to

CHIME and open the door. If chime

sounds, then the gap distance is

correct. If it does not sound, move

either the alarm or magnet closer

so that gap distance is 1/2” or less.

4.Once you have conrmed the

correct positioning of the magnet

and alarm, lift the alarm o the

mounting plate and apply rm

pressure directly to the plate

itself. Once secured, reattach the

alarm to the mounting plate.

5.Apply rm pressure to the magnet

to secure its position as well.

1. Locate ALARM/CHIME switch on

right side of the alarm unit.

2.Slide switch to ALARM position.

3.Choose HOME or AWAY on the left

side of the alarm unit.

HOME MODE

In HOME mode, the alarm will sound

when the gap between the alarm and

the magnet is greater than 1/2” (i.e.

the door is opened).

AWAY MODE

In AWAY mode, there will be a 45 second

exit delay before the unit is armed.

The alarm’s indicator light will ash

red quickly, alerting you that the unit

has been activated and has begun the

45-second count down. The delay allows

time for you to leave the protected area

without triggering the alarm. When

returning to the protected area, there is

a 30 second delay to allow time to enter

4-digit code before the alarm will sound.

Operating In The Alarm Mode

Inhaltsverzeichnis

Sprachen:

Andere Philips Sicherheitssystem Handbücher

Philips

Philips AutoDome TC700 Series Bedienungsanleitung

Philips

Philips In.Sight M100 Bedienungsanleitung

Philips

Philips VSS2364/C4T Bedienungsanleitung

Philips

Philips lifeline Bedienungsanleitung

Philips

Philips Lifeline FD100 Bedienungsanleitung

Philips

Philips VSS7374/D4T Bedienungsanleitung

Philips

Philips FD100SL Bedienungsanleitung

Philips

Philips M100/37 Bedienungsanleitung

Philips

Philips VSS2360/00T Bedienungsanleitung

Philips

Philips VSS7370/D3T Bedienungsanleitung

Philips

Philips LDH2544/10 Bedienungsanleitung

Philips

Philips In.Sight M100 Bedienungsanleitung

Philips

Philips LBB 1370 Bedienungsanleitung

Philips

Philips 26PF9631D Bedienungsanleitung

Philips

Philips HF3506/05 Bedienungsanleitung

Philips

Philips LRM3220D/27 Bedienungsanleitung

Philips

Philips VSS2902 Bedienungsanleitung

Philips

Philips VSS2360/00T Bedienungsanleitung

Philips

Philips B200G Bedienungsanleitung

Philips

Philips ADIM ADM0101 Bedienungsanleitung

Philips

Philips MathLine 27CE7695 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung