Philips AD6000W/10 Bedienungsanleitung

www.philips.com/welcome

AD6000W/10

EN User manual

English

Contents

1 Important 4

Safety 4

Notice 5

2 Your Entertainment System 7

Introduction 7

What’s in the box 7

What else you need 7

Overview of the main unit 8

Get started to use AirPlay 8

3 Prepare 9

Connect power 9

Turn AD6000W on 9

4 Connect to your home Wi-Fi network

for AirPlay 10

Scenario 1: Connect to a WPS router 10

Scenario 2: Connect to a non-WPS router 11

5 Play 17

Stream audio from your iTunes music library

to AD6000W 17

Control play 18

Use advanced sound settings 18

Play/charge your iPod/iPhone/iPad through

USB socket 19

Play from an external device 19

6 Updatermware 20

Download the update le 20

Update from the conguration page 20

7 Product information 22

Specications 22

8 Troubleshooting 23

gDo not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

hDo not remove the casing of this product.

iDo not expose the product to dripping /

splashing water, rain or high humidity.

jKeep this product away from direct

sunlight,nakedamesorheat.

kDo not install near any heat sources

such as radiators, heat registers, stoves,

or other electrical equipment (including

ampliers).

lDo not place any other electrical

equipment on the product.

mDo not place any sources of danger

on the product (e.g. objects containing

liquids,burningcandles).

nWhere the mains plug or an appliance

coupler is used as the disconnect device,

the disconnect device shall remain readily

operable.

Warning

•Never remove the casing of this apparatus.

•Never lubricate any part of this apparatus.

•Never place this apparatus on other electrical

equipment.

•Keep this apparatus away from direct sunlight, naked

ames or heat.

•Ensure that you always have easy access to the power

cord, plug or adaptor to disconnect this apparatus from

the power.

Risk of overheating! Never install this apparatus

in a conned space. Always leave a space of

at least four inches around this apparatus for

ventilation. Ensure curtains or other objects

never cover the ventilation slots on this

apparatus.

1 Important

Safety

Information for Europe:

Know these safety symbols

The ‘exclamation mark’ calls attention to

features for which you should carefully read the

supplied literature to prevent operating and

maintenance problems.

The ‘lightening bolt’ symbol indicates uninsulated

components within the product that can cause

an electric shock.

To reduce the risk of re or electric shock, do

not expose the product to rain or moisture and

do not place any objects lled with liquids, such

as vases, on the product.

aRead these instructions.

bKeep these instructions.

cHeed all warnings.

dFollow all instructions.

eDo not use this product near water.

fClean only with dry cloth.

English

Please inform yourself about the local separate

collection system for electrical and electronic

products.

Please act according to your local rules and

do not dispose of your old products with your

normal household waste. Correct disposal of

your old product helps to prevent potential

negative consequences for the environment and

human health.

Environmental information

All unnecessary packaging has been omitted.

We have tried to make the packaging easy to

separate into three materials: cardboard (box),

polystyrene foam (buffer) and polyethylene

(bags, protective foam sheet.)

Your system consists of materials which can

be recycled and reused if disassembled by

a specialized company. Please observe the

local regulations regarding the disposal of

packaging materials, exhausted batteries and old

equipment.

“Made for iPod,”“Made for iPhone,” and “Made

for iPad” mean that an electronic accessory

has been designed to connect specically to

iPod, iPhone, or iPad, respectively, and has

been certied by the developer to meet

Apple performance standards. Apple is not

responsible for the operation of this device

or its compliance with safety and regulatory

standards. Please note that the use of this

accessory with iPod, iPhone, or iPad may affect

wireless performance.

Notice

This product complies with the radio

interference requirements of the European

Community.

The device can be operated in the EU without

restrictions indoor, but cannot be operated

outdoors in France in the whole of the band

until further notice.

This product complies with the requirement of

the 1999/5/EC directive.

Modications

Modications not authorized by the

manufacturer may void user’s authority to

operate this product.

Your product is designed and manufactured

with high quality materials and components,

which can be recycled and reused.

When this crossed-out wheeled bin symbol is

attached to a product it means that the product

is covered by the European Directive 2002/96/

EC.

AirPlay, iPod, and iPhone are trademarks of

Apple Inc., registered in the U S. and other

countries. iPad is a trademark of Apple Inc.

Class II equipment symbol:

CLASS II apparatus with double insulation, and

no protective earth provided.

Note

•The type plate is located on the bottom of the

apparatus.

English

Tip

•Please visit www.philips.com/welcome for information

about more Philips AirPlay-enabled devices.

With AD6000W, you can also:

• charge your iPod/iPhone/iPad through

the USB socket with an Apple USB

cable (not supplied).

• play your iTunes music library on your

iPod/iPhone/iPad through the USB

socket directly while charging.

• play music from other audio devices

through the MP3-LINK socket.

What’s in the box

Check and identify the contents of your

package:

• Main unit (with a built-in Wi-Fi

module)

• 1 x AC power adapter

• 1 x MP3 link cable

• User manual (in CD-ROM)

• Quick start guide

What else you need

To stream audio wirelessly by AirPlay, you need:

• A Wi-Fi certied router

• A host for your iTunes music library,

for example, an iPod touch/iPhone/

iPad installed with iOS 4.3 (or later)

or a Wi-Fi enabled PC/Mac installed

with iTunes 10 (or later)

Your AD6000W should be connected to the

same local network as your iTunes host device

through the Wi-Fi router.

2 Your

Entertainment

System

Congratulations on your purchase, and

welcome to Philips! To fully benet from the

support that Philips offers, register your product

at www.philips.com/welcome.

If you contact Philips, you will be asked for the

model and serial number of this apparatus.The

model number and serial number are on the

bottom of the apparatus.Write the numbers

here:

Model No. __________________________

Serial No. ___________________________

Introduction

Apple AirPlay technology enables you to play

your iTunes music library, hosted on a Mac, PC,

iPhone, iPod touch, or iPad on any AirPlay-

enabled device (for example, your AD6000W)

connected to the Wi-Fi network.

With an AirPlay-enabled device (for example,

your AD6000W), you can:

• stream audio from your iTunes music

library to any room in your house

• choose which AirPlay-enabled devices

you want to play music on (if you

have more than one such devices in

your house)

• stream audio to multiple AirPlay-

enabled devices at the same time

(from the iTunes music library on your

PC/Mac only)

eMP3-LINK

• Connect an external audio player

through the supplied MP3 link cable.

fDC IN

• Connect the power adaptor.

gUSB

• Connect an iPod/iPhone/iPad through

an Apple USB cable (not supplied).

Get started to use AirPlay

To get started with AirPlay, you need to:

1Upgrade your iPod touch/iPhone/iPad to

the latest iOS version (iOS 4.3 or later).

• Or install the latest version of iTunes

(iTunes 10 or later) on your PC/Mac.

2Connect power to AD6000W, then turn it

on (see ‘Prepare’ on page 9).

3Connect AD6000W to your existing home

Wi-Fi network (see ‘Connect to your

home Wi-Fi network for AirPlay’ on page

10).

4Make sure that your iPod touch/iPhone/

iPad or PC/Mac are also connected to the

same Wi-Fi network.

List of compatible iTunes host devices

for AirPlay

In terms of AirPlay, AD6000W is compatible

with:

• a Wi-Fi enabled PC/Mac installed with

iTunes 10 (or later); and

• the following iPod/iPhone/iPad models

installed with iOS 4.3 (or later):

• iPad 2

• iPad

• iPhone 4

• iPhone 3GS

• iPod touch (2nd, 3rd, and 4th

generation)

Overview of the main unit

aPower indicator

b+/-

• Adjust volume.

• Turn the unit on/off.

• (Press and hold) reset the unit.

dWI-FI SETUP button/indicator

• Connect the unit to a Wi-Fi network.

• Show the Wi-Fi connection status of

the unit.

English

Turn AD6000W on

1Press on the back to turn the unit on.

2Wait for successful boot-up of the unit.

»The boot-up takes about 35 seconds.

»During boot-up, the Wi-Fi SETUP

indicator on the back of the unit blinks

green quickly.

»After boot-up, if no Wi-Fi connection

has been set up for AD6000W, the

Wi-Fi SETUP indicator starts to blink

green slowly.

• To switch the unit to Eco standby mode,

press again.

• To switch the unit on from Eco standby

mode, press again.

3 Prepare

Always follow the instructions in this chapter in

sequence.

Connect power

Caution

•Risk of product damage! Make sure that the power

supply voltage matches the voltage printed on the

bottom of the unit.

•Risk of electric shock! When you unplug the AC

adaptor, always pull the plug from the socket. Never

pull the cord.

•Before you connect the AC adaptor, make sure that you

have completed all the other connections.

• Connect the AC power cord to

• the DC IN socket on the back of the

unit.

• the wall power socket.

Before connection of AD6000W to you home

Wi-Fi network, check the points below.

1Make sure that your Wi-Fi router is

powered on and working properly.

2Make sure that AD6000W has been

powered on and booted up successfully

(see ‘Turn AD6000W on’ on page 9).

3Identify the type of your Wi-Fi router (see

the user manual of your Wi-Fi router for

details).

Scenario 1: Connect to a

WPS router

Note

•Before you press any button on AD6000W, make sure

that AD6000W has been booted up successfully (see

‘Turn AD6000W on’ on page 9).

1Press the WPS button on your home Wi-Fi

router.

2Shortly after step 1, press Wi-Fi SETUP on

the back of AD6000W.

»The Wi-Fi SETUP indicator blinks red,

yellow and green alternately.

»Within 2 minutes, the WI-FI SETUP

indicator stops blinking and stays green,

and the unit beeps.

WPS

4 Connect to

your home Wi-

Fi network for

AirPlay

To connect AD6000W to your existing home

Wi-Fi network, you need to apply your home

Wi-Fi settings to AD6000W.

You can do this in two ways (depending on

which type of Wi-Fi router you use):

• Automatically - if your Wi-Fi router

is WPS (Wi-Fi Protected Setup)-

enabled and supports PBC (Push

Button Connection) (see Scenario 1:

Connect to a WPS router’ on page

10)

• Manually - if your Wi-Fi router does

not support WPS (see ‘Scenario 2:

Connect to a non-WPS router’ on

page 11)

Once connected successfully, AD6000W will

remember your home Wi-Fi settings.Then

you can enjoy AirPlay whenever AD6000W is

powered on and connected to your home Wi-

Fi network automatically.

English

The Wi-Fi enabled device can be an iPod touch/

iPhone/iPad or a Wi-Fi enabled PC/Mac.

Follow the sequence below for connection of

AD6000W to a non-WPS Wi-Fi router.

1Collect settings of your home Wi-Fi router

and write down on paper for use during

AD6000W Wi-Fi setup (see ‘Collect

settings of your home Wi-Fi router’ on

page 11).

2Switch AD6000W to Assisted Wi-Fi Setup

mode (see Switch AD6000W to Assisted

Wi-Fi Setup mode’ on page 12).

»A new Wi-Fi network created by

AD6000W will appear, with the

network name (SSID) of Philips Fidelio

AirPlay.

3Connect your Wi-Fi enabled device to the

newly created Wi-Fi network temporarily

(see ‘Connect your Wi-Fi enabled device to

the newly created Wi-Fi network’ on page

12).

4Open the built-in web page of AD6000W

with the Internet Browser of your Wi-Fi

enabled device (see ‘Open the built-in web

page of AD6000W’ on page 14).

5Change the internal Wi-Fi settings of

AD6000W based on the settings you

wrote on paper at step 1 (see ‘Change the

internal Wi-Fi settings of AD6000W’ on

page 15).

6Restore your Wi-Fi enabled device back

to your existing home Wi-Fi settings (see

‘Restore your Wi-Fi enabled device back to

your existing home Wi-Fi setting’ on page

16).

Collect settings of your home Wi-Fi

router

Note

•Always consult the user manual of your home Wi-Fi

router for detailed instructions.

»AD6000W is connected to your home

Wi-Fi network successfully.

Tip

•For some Wi-Fi routers, you may need to hold the

WPS button for Wi-Fi connection or enable the WPS

PBC function from the router conguration pages. See

the user manuals of the specic routers for details.

•If the Wi-Fi SETUP indicator on AD6000W blinks

yellow, it means that the Wi-Fi connection has failed.

Please wait for 2 minutes and try again. If the problem

remains, try to set up the Wi-Fi connection manually

(see ‘Scenario 2: Connect to a non-WPS router’ on

page 11).

•If the Wi-Fi connection fails again, press and hold on

the back of AD6000W to reset it, and then try again.

Scenario 2: Connect to a

non-WPS router

Note

•You can also follow the procedures below to connect

AD6000W to a WPS router manually.

To connect AD6000W to a Wi-Fi router

manually, you need access to AD6000W’s

built-in conguration web page for change of

its internal Wi-Fi settings.To do so, you need a

Wi-Fi enabled device with an Internet browser

for temporary Wi-Fi connection to AD6000W.

Andere Handbücher für AD6000W/10

Inhaltsverzeichnis

Andere Philips Sprecher Handbücher

Philips

Philips HTL3110B Bedienungsanleitung

Philips

Philips BT2200 Bedienungsanleitung

Philips

Philips AW5000 Bedienungsanleitung

Philips

Philips NTX400 Bedienungsanleitung

Philips

Philips DS7650 Bedienungsanleitung

Philips

Philips TANX20 Bedienungsanleitung

Philips

Philips MMS 430 Bedienungsanleitung

Philips

Philips BT50A Bedienungsanleitung

Philips

Philips SPA9120B Bedienungsanleitung

Philips

Philips BM90 Bedienungsanleitung

Philips

Philips HTS8141 Bedienungsanleitung

Philips

Philips Fidelio XS1 Bedienungsanleitung

Philips

Philips HTS3365 Bedienungsanleitung

Philips

Philips HSB4383 Bedienungsanleitung

Philips

Philips SPA2210W/10 Bedienungsanleitung

Philips

Philips TAS3505 Bedienungsanleitung

Philips

Philips SBCBC8210/06 Bedienungsanleitung

Philips

Philips MMS3160B Bedienungsanleitung

Philips

Philips CSS5530G Bedienungsanleitung

Philips

Philips SPA7300 Bedienungsanleitung

Philips

Philips NORELCO BT1300 Bedienungsanleitung

Philips

Philips DGX320B Bedienungsanleitung

Philips

Philips SPA1305/10 Bedienungsanleitung

Philips

Philips LSBS900/00S Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung