Philips 27PS60S321 Bedienungsanleitung

Philips Consumer Electronics

Technical Service Data

Service and Quality

Service Publications Dept.

One Philips Drive

P.O. Box 14810

Knoxville, TN 37914

REFER TO SAFETY GUIDELINES

SAFETY NOTICE: ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE

HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS

TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.

CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING

Manual 7629

Model no.: 27PS60S321

First Publish: 12740 T8

Rev. Date: 2002-06-06

Print Date: 7/8/2004

Pg. SCHEMATIC DIAGRAMS AND PC BOARDS

1. PCB Locations

2. Power Supply (Diagram A1)

3. Line Deflection (Diagram A2)

4. Frame Deflection (Diagram A3)

5. Tuner IF (Diagram A4)

6. Video IF And Sound IF (Diagram A5)

7. Synchronization (Diagram A6)

8. Control (Diagram A7)

9. Audio Amplifier (Diagram A8)

10. BTSC (Stereo/SAP) Decoder (Diagram A9)

11. Audio/Video Source Switching (Diagram A10)

12. BTSC - NDBX Stereo Decoder (Diagram A11)

13. Front I/O + Control, Headphone (Diagram A12)

14. Rear I/O Cinch (Diagram A13)

15. PIP Interface (Diagram A16)

16. CRT Panel (Diagram B1)

17. Side AV and Headphone Panel (Diagram C)

18. PIP Panel (Diagram P)

19. Main Panel (component side)

20. Main Panel (copper side)

21. CRT Panel (component side)

22. CRT Panel (copper side)

23. Headphone Panel (component side)

24. Side AV Panel (component side)

25. PIP panel (component side)

26. PIP panel (copper side)

27. Top Control Panel (component side)

28. EPS Panel PCB (Top View only)

29. Card Interface Panel PCB (Top View)

30. Card Interface Panel PCB (Bottom View)

Philips Consumer Electronics

Technical Service Data

Service and Quality

Service Publications Dept.

One Philips Drive

P.O. Box 14810

Knoxville, TN 37914

REFER TO SAFETY GUIDELINES

SAFETY NOTICE: ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE

HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS

TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.

CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING

Manual 7629

Model no.: 27PS60S321

First Publish: 12740 T8

Rev. Date: 2002-06-06

Print Date: 7/8/2004

Mechanical Diagrams

MAIN CABINET EXPLODED VIEW Page: 1 of 1

Philips Consumer Electronics

Technical Service Data

Service and Quality

Service Publications Dept.

One Philips Drive

P.O. Box 14810

Knoxville, TN 37914

REFER TO SAFETY GUIDELINES

SAFETY NOTICE: ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE

HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS

TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.

CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING

Manual 7629

Model no.: 27PS60S321

First Publish: 12740 T8

Rev. Date: 2002-06-06

Print Date: 7/8/2004

Electrical Adjustments

Alignments

Index of this chapter:

1. General Alignment Conditions

2. Commercial Models SDAM Entry

3. Hardware Alignments

4. Software Alignments and Settings

Note: The Service Default Alignment Mode (SDAM) is described in the "Service

Modes, Error Codes and Fault Finding" section. SDAM menu navigation is performed

by using the MENU UP, MENU DOWN, MENU LEFT, and MENU RIGHT keys of the

remote control transmitter.

General Alignment Conditions

Perform all electrical adjustments under the following conditions:

AC voltage and frequency: 110 V (± 10 %), 60 Hz (± 5 %).

Connect the television set to the AC power via an isolation transformer.

Allow the television set to warm up for approximately20 minutes.

Measure the voltages and waveforms in relation to chassis ground (with the

exception of the voltages on the primary side of the power supply). Never use

heatsinks as ground.

Test probe: Ri > 10 MO; Ci < 2.5pF.

Use an isolated trimmer/screwdriver to perform the alignments.

Service Default Alignment Mode (SDAM) Entry for

Commercial Models

Note: For commercial models, a master setup remote control is required in order to access the Service

Default Alignment Mode (SDAM).

1. Use the master setup remote control to identify the television’s operational mode (either

“consumer” or “commercial”). Place the master setup remote control in setup mode by

pressing the TV SETUP key.

2. Press the RECALL key. Information similar to the following will be displayed.

Status Item Status Data Meaning

SYSTEM STATUS

(L011TV-US4PV) Information title

MODE COMMERCIAL/CONSUMER Operational mode

CHANNEL CHANNEL, INPUT Currently tuned channel/input

DCM OFF/ON Data Comm. Module online/offline

CODES 209 222 1 33 Internal data for factory/service use

SIGNAL TUNED/NOT TUNED Valid signal present/absent

OP HRS 0031h Number of hours set has operated (hex)

ERRORS 0 0 0 0 0 Internal data for factory/service use

VERSION 3.3 Microprocessor software version

3. To change the television’s mode, ensure the master setup remote control is in setup mode,

then press the 0-2-4-9-9-5-MENU keys in order, without permitting the display to time out

while entering the key sequence.

ote: If the operational mode is changed, the television must be turned off and then back on to

complete the mode change. When the television is in consumer mode, do not use the master setup

remote control to activate commercial mode features.

4. When the television is in commercial mode, the Institutional Television Menu may be accessed by

pressing the MENU button. Though the specific items in the menu will vary, information similar to

the following will be displayed.

Menu Item Settings / Options

(MENU TITLE) SETUP MENU / MAIN MENU

LANGUAGE ENGLISH / ESPANOL / FRANCAIS

CHANNEL INSTALL >

CABLE TUNING ON / OFF

BRIGHTNESS - - - | - - - 31

COLOR - - - | - - - 31

CONTRAST - - - | - - - 31

SHARPNESS - - - | - - - 31

TINT - - - | | - - - 0

NOISE REDUCTION ON / OFF

SOUND MODE MONO / STEREO

SAP OFF / NO SAP / ON

AUDIO OUT FIXED / VARIABLE

BALANCE - - - | - - - 0

TREBLE - - - | - - - 31

BASS - - - | - - - 31

INCRED STEREO ON / OFF

AVL ON / OFF

VOLUME BAR ON / OFF

MIN VOLUME | - - - - - - 0

MAX VOLUME - - - - - - | 63

SWITCH ON VOLUME - - - | - - - 31

SWITCH ON CHANNEL CH. 1-125 / FRONT / AUX / S-VIDEO / CVI / STANDARD

POWER ON STANDARD / FORCED

CHANNEL DISPLAY NUMBER / LABEL / ALL / NONE

KEYBOARD LOCK ON / OFF

ESP 1 – 99 / OFF

AUDIO / VIDEO MUTE OFF / BLACK / BLUE

EXT AUD / VID OUT ON / OFF

WELCOME MESSAGE >

CHANNEL GUIDE POWER ON / OFF / ON

REMINDER ON / OFF

3 DIGIT ENTRY ON / OFF

A/CH A/V SWITCH ON – OFF

CC OFF / CC-1 / CC-2 / CC ON MUTE

SAVE CC ON / OFF

V-CHIP MENU ITEM ON / OFF

SAVE V-CHIP ON / OFF

V-CHIP SETUP >

SLEEPTIMER OFF / 15 / 30 / 45 / 60 / 90 / 120 / 180 / 240

EXIT >

5. After making changes to the settings, the EXIT option may be used to leave the Institutional

Television Menu.

Hardware Alignments

Figure: Mono Carrier (Top View) LS

Vg2 Adjustment

1. Enter SDAM:

2. Press the following key sequence on the remote control transmitter:

0-6-2-5-9-6-MENU

Do not allow the display to time out between entries while keying the sequence.

3. Use the MENU UP/DOWN keys to highlight the WHITE TONE sub menu.

4. Press the MENU LEFT or MENU RIGHT key to enter the WHITE TONE sub

menu.

5. In the WHITE TONE sub menu, press the MENU UP/DOWN keys to select

NORMAL RED, NORMAL GREEN, or NORMAL BLUE.

6. Use the MENU LEFT/RIGHT keys to set the values of NORMAL RED, NORMAL

GREEN and NORMAL BLUE to 40.

7. Press the MENU button twice to enter the normal user menu.

8. In the normal user menu, use the MENU UP/DOWN keys to highlight the

PICTURE sub menu (if necessary).

9. Press the MENU LEFT/RIGHT keys to enter the PICTURE sub menu.

10.Use the MENU UP/DOWN keys to select PICTURE. Be sure to record the

current value of PICTURE.

11.Use the MENU LEFT/RIGHT keys to set the value of PICTURE to zero.

12.Use the MENU UP/DOWN keys to select BRIGHTNESS. Be sure to record the

current value of BRIGHTNESS.

13.Use the MENU LEFT/RIGHT keys to set the value of BRIGHTNESS to minimum

(OSD just visible in a dark room).

14.Press the MENU button twice to return to the top level SDAM menu.

15.Press the STATUS/EXIT button to hide the SDAM onscreen display.

16.Connect the RF output of a video pattern generator to the antenna input.

17.Input a "black picture" test pattern to the television set.

18.Set the oscilloscope to 50 V/div and the time base to 0.2 milliseconds (external

triggering on the vertical pulse).

19.Ground the scope at the CRT panel and connect a 10:1 probe to one of the

cathodes of the picture tube socket (see schematic diagram B).

20.Measure the cut off pulse during first full line after the frame blanking (see Fig.

8-2). You will see two pulses, one being the cut off pulse and the other being the

white drive pulse. Choose the one with the lowest value; this is the cut off pulse.

21.Select the cathode with the highest VDC value for the alignment. Adjust the V

Cut-Off of this gun with the SCREEN potentiometer (see Fig. 8-1) on the LOT to

the correct value (see table below).

22.Press the STATUS/EXIT button to display the SDAM onscreen display.

23.Press the MENU button to enter the normal user menu.

24.In the normal user menu, use the MENU UP/DOWN keys to highlight the

PICTURE sub menu (if necessary).

25.Press the MENU LEFT/RIGHT keys to enter the PICTURE sub menu.

26.Use the MENU UP/DOWN keys to select PICTURE.

27.Use the MENU LEFT/RIGHT keys to reset the value of PICTURE to the original

value.

28.Use the MENU UP/DOWN keys to select BRIGHTNESS.

29.Use the MENU LEFT/RIGHT keys to reset the value of BRIGHTNESS to the

original value.

30.Press the MENU button twice to return to the top level SDAM menu.

31.Use the POWER button on the remote control transmitter or the POWER button

on the television set to turn off the television set. This will save the changes

made in SDAM.

Figure: V Cut-Off

Table: Cut-off Voltage, Large Screen

Screen Size Cut-off Voltage

25/28Tesla, 25/28BLD +140V +/- 4V

20RF/21RF/25RF/29RF,21RF Pin-Free, 25"HF LA,

25V/27V/32V/35V/25"/33"/28BLS, 29",29SF EU, +145V +/- 4V

21RF AP/CH, 25" AP/CH, 25RF/29RFAP/CH, 29SF AP +155V +/- 4V

21RF Ph, 24/28/32WS BLD,29RF (Eu), 28/32WSRF +160V +/- 4V

Focusing

1. Connect the RF output of a video pattern generator to the antenna input.

2. Input a circle or crosshatch test pattern to the television set.

3. Press the AUTO PICTURE button on the remote control transmitter repeatedly to

choose PERSONAL or MOVIES picture mode.

4. Adjust the FOCUS potentiometer (see Fig. 8-1)until the vertical lines near the left

and right sides of the screen, and near the horizontal center of the screen, are at

minimum width without visible haze.

Software Alignments and Settings

The following options are performed in the Service Default Alignment Mode (SDAM).

SDAM is described in the "Service Modes, Error Codes and Fault Finding" section.

The following alignments are explained:

1. OPTIONS

2. TUNER

3. WHITE TONE

Inhaltsverzeichnis

Andere Philips Fernseher Handbücher

Philips

Philips 34 IN WIDESCREEN HDTV MONITOR 34PW862H Handbuch

Philips

Philips 32PFL3008K Bedienungsanleitung

Philips

Philips 20PFL4122/79 Bedienungsanleitung

Philips

Philips 21PT9457 Bedienungsanleitung

Philips

Philips 32PT842H99 Handbuch

Philips

Philips 21PT4525/V7 Bedienungsanleitung

Philips

Philips 32PW962A/05 Bedienungsanleitung

Philips

Philips 28PT4501 Bedienungsanleitung

Philips

Philips 29PT8006 Bedienungsanleitung

Philips

Philips 42PF7320A Gebrauchs- und Wartungshandbuch

Philips

Philips 21PT1727 Bedienungsanleitung

Philips

Philips MG2.1E Bedienungsanleitung

Philips

Philips 21PT1354 Bedienungsanleitung

Philips

Philips 52PFL7762D/05 Bedienungsanleitung

Philips

Philips 43PUS6031 Bedienungsanleitung

Philips

Philips TV 34PT9421 /93 Bedienungsanleitung

Philips

Philips Magnavox PR0925B Bedienungsanleitung

Philips

Philips 32PS60B Bedienungsanleitung

Philips

Philips 32PW8718 Bedienungsanleitung

Philips

Philips 75PUS7101/12 Bedienungsanleitung

Philips

Philips 27PTG015D Bedienungsanleitung

Philips

Philips PL7119C Bedienungsanleitung

Philips

Philips 34PW8621 Handbuch

Philips

Philips 8807 Series Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Toshiba

Toshiba 27A10 Bedienungsanleitung

Hitachi

Hitachi 32FX48B Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Sony

Sony XBR-100Z9D Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Sylvania

Sylvania 6427FB Bedienungsanleitung

Sanyo

Sanyo CE19LD90N-B Bedienungsanleitung

North State

North State TV2GO Bedienungsanleitung

RCA

RCA RTU7877 Bedienungsanleitung

Sharp

Sharp 21K-FG1RU Bedienungsanleitung

Sony

Sony Esprit TAV-L1 Bedienungsanleitung

Grundig

Grundig 43 VLE 4820 Bedienungsanleitung

Samsung

Samsung LN26C350D1D Bedienungsanleitung