Philips AUT3234 Bedienungsanleitung

Under-the-sink ltration

AUT3234

Water Solutions

User manual 1EN Manual del usuario 16ES

Manuel d'utilisation 33FR Manuale utente 49IT

Руководство пользователя 66RU

Content

I. Product Introduction 1

II. Product Specifications 1

III. Product overview and

installation illustration

IV. Installation

Install the three-way ball valve

Install the faucet

Install the system

V. Usage instruction

Before the first-time use

User interface

VI. Maintenance

Routine maintenance

Filter lifetime

Filter cartridge replacement

VII. Precautions

Warning

VIII. Troubleshooting 12

IX. Guarantee & Service 13

X. Packaging list 14

Installation

I. Product Introduction

Congratulations on your purchase and welcome to Philips! Our under-the-sink

water filtration system AUT3234 comes with a 4-stage ultrafiltration, which

eectively reduces particles, heavy metals, volatile organic compounds, pesticides,

bacteria, and pollutants down to 0.01 micron*, while retaining beneficial minerals

at the same time.

Read this user manual carefully before you use the appliance. Save it for future

reference.

* The substances removed or reduced by this system are not necessarily in all

user’s water.

** When the inlet water pressure exceeds 0.4 MPa, a pressure relief valve should

be installed before the system. When the inlet water pressure is below 0.1 MPa,

a pressure booster should be installed before the system. The pressure relief valve

and extra pressure booster need to be purchased separately.

Product name Philips under-the-sink water filtration system

AUT3234

2 liters/minute

CBPA filter: 4000 liters

UF filter: 8000 liters

CB filter: 4000 liters

Product model

Water flow rate

Filtration capacity

Inlet water pressure 0.1-0.4 MPa**

Inlet water temperature 5℃-38℃

Applicable water source

Municipal tap water, which meets all European

Directive on Water for Human Consumption 98/83

requirements and its national transpositions in

the various EU member states.

II. Product Specification

Rated voltage

4.5V

III. Product overview and installation illustration

Carbon block and sediment filter 2-in-1 filter (CBPA)

Hollow ber membrane lter (UF)

Carbon block filter (CB)

1/4” PE pipe

System

Hot

Cold

Filtered water outlet pipe

Faucet

Water inlet pipe

Three-way ball valve

Quick connect fitting

Faucet and accessory

1 2

CBPA

IV. Installation

Note:

- Before installation, it is important to check the condition of the system to

make sure it has not been damaged during transport.

- Unpack the system and its accessories. Remove the protective packaging material.

Recyclable materials have been used for the packaging and should be disposed

of in the appropriate recycling bins or at the specific local recycling center.

Warning: Keep plastic bags out of the reach of children, as they may be dangerous.

- Check if anything is missing according to the packing list and the overview.

- Given that the system will improve the quality of your drinking water, all tools

to be used in the installation process should be clean, rust and grease-free.

- The installation process should be carried out under appropriate hygienic

conditions, taking all necessary precautions concerning materials and components

that will come into contact with water to be treated or consumed.

- Avoid external contamination of the system through improper handling, using

gloves, sanitizing gel, and washing hands as often as is necessary during the

installation process, first use, and system maintenance.

- The system and installation shall comply with applicable local regulations.

- This product cannot be disposed of with other domestic waste products.

At the end of the product’s service life, it should be returned to the place of

purchase, or at a local recycling center, indicating that it contains electric

and electronic components. The appropriate collection and treatment

of the product, which no longer are to be used, contributes to the

preservation of natural resources and avoids any potential public health risks.

1. Install the three-way ball valve

a. Turn off the cold water supply. Turn on the kitchen cold water faucet to release

the pressure and allow water to drain from the line. Disconnect the cold water

hose from the cold water valve.

Cold

(1) (2)

Hot Cold

b. Slide the nut of the three-way ball valve onto the 1/4" PE pipe and insert the

pipe into the opening of the three-way ball valve. Tighten the nut with a wrench.

c. Install the three-way ball valve on the cold

water valve. Please don’t miss the gasket

inside the three-way ball valve during

installation.

d. Connect the cold water hose with the

three-way ball valve and screw it tightly

with a wrench. Please don’t miss the

gasket in the cold water hose during

installation.

Gasket

(1)

(2)

(1) (2)

Gasket

Water outlet

Lever

Washer

Spacer

Nut

Quick connect tting

e. Switch off the three-way ball valve. Turn on

the cold water supply. Wipe the connections

with a tissue to see if there is leakage. If the

tissue stays dry, it means the three-way ball

valve is installed properly.

Hot Cold

2. Install the faucet

Note:

Select an appropriate installation position. The environment where the faucet is

installed should adhere to any appropriate hygiene and sanitation conditions.

Make sure the faucet sits flat on top of the sink or countertop surface.

a. Drill a hole with a diameter of about 25mm. Skip this step if there is already a

hole in the sink or the countertop surface.

b. Install the faucet according to the diagram.

Screw the faucet stem nut all the way up the

faucet stem, and tighten it to secure the faucet.

3. Installing the system

Note:

Please check if there is sucient space for installing the system itself, its accessories,

connections, and for servicing and repair. Under no circumstances should the system

be installed outdoors. The environment where the system is installed should

adhere to any appropriate hygiene and sanitation conditions. Avoid any external

dripping liquids from pipes or drains etc onto the system.

(1)

(2)

This system should be placed on a stable and at surface. Keep the system away

from heat. It shall not be placed in a place that may have inammable gas leakage.

a. Press down the collets and pull out the plugs

of the water inlet and outlet holes in the back

of the system.

b. Connect the water inlet and the three-way ball valve.

Measure the length of the 1/4" pipe you

need to connect the system and the

three-way ball valve, and cut it accordingly

with a pipe cutter. Insert the other end of

the 1/4" pipe which has been connected

with the three-way ball valve into the water

inlet hole in the back of the system. Use a

clip to secure the pipe at the hole.

Note: The inlet water pressure should be within 0.1-0.4 MPa. If the pressure is too

low, a pressure booster should be installed before the system. If the pressure

is too high, a pressure relief valve should be installed before the system.

The pressure relief valve and extra pressure booster need to be purchased

separately.

c. Connect the water outlet and the faucet.

Measure the length of the 1/4” pipe you need, and cut it with a pipe cutter.

Insert one end of the pipe into a quick connect fitting, and connect the quick

connect fitting on the stem of the faucet. Use a clip to secure the pipe. Insert

the other end of the 1/4" pipe into the water outlet hole in the back of the

system until it stops.

1 2

d. Put in 3 AAA batteries.

e. Move the system to its space in the under-the-sink cabinet.

f. Remove the plastic wrap of the lter cartridges. Insert the lter cartridges in the

system accordingly, and turn them clockwise to align the triangle icon on the

filter cartridge with the lock icon on the system.

g. Check if the system is installed properly, and turn on the three-way ball valve.

AAA

CBPA

(1)

(2)

Inhaltsverzeichnis

Sprachen:

Andere Philips Wasserfiltersystem Handbücher

Philips

Philips AUT2015 Bedienungsanleitung

Philips

Philips WP3893 Bedienungsanleitung

Philips

Philips AC4012 Bedienungsanleitung

Philips

Philips AWP2980 Bedienungsanleitung

Philips

Philips Saeco AquaClean CA6903 Bedienungsanleitung

Philips

Philips AC4141 Bedienungsanleitung

Philips

Philips AC4142 Bedienungsanleitung

Philips

Philips AWP3753 Bedienungsanleitung

Philips

Philips AWP2900 Bedienungsanleitung

Philips

Philips WP3810 Bedienungsanleitung

Philips

Philips AUT3015 Bedienungsanleitung

Philips

Philips AWP1811 Bedienungsanleitung

Philips

Philips AC4144 Bedienungsanleitung

Philips

Philips WP3822 Micro X-Pure Bedienungsanleitung

Philips

Philips AWP2900 Bedienungsanleitung

Philips

Philips WP3891/01 Bedienungsanleitung

Philips

Philips WP3820 Bedienungsanleitung

Philips

Philips Saeco AquaClean CA6903 Bedienungsanleitung

Philips

Philips Saeco AquaClean CA6903/47 Bedienungsanleitung

Philips

Philips WP3890/01 Bedienungsanleitung

Philips

Philips Micro Pure WP3811 Bedienungsanleitung

Philips

Philips WP3892 Bedienungsanleitung

Philips

Philips AUT3268 Bedienungsanleitung

Philips

Philips Pure Taste WP3861 Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung