Phonak TVLink basestation Bedienungsanleitung
029-1013-02/V1.00/2010-04/A+W/FO Printed inSwitzerland
©Phonak AG All rights reserved
EU Representative:
Phonak GmbH
D-70736 Fellbach-Oeffingen
Germany
!
0678
1
Phonak TVLink basestation
The TVLink basestation is connected to your TV (or any
other audio source) and wirelessly sends audio signals
from your TV to an A2DP Headset within a range of up
to 30 meters (100 ft).
Buttons
(a) ON/OFFbutton
(b) Volume control (up)
(c) Volume control(down)
Inputs
(d) Power input (mini-USB)
(e) Audio input(3.5 mm jack)
(f) Charging slot
(g) Status light
1. Device description
(b)(c)
(f) (g)
(d) (e)
(a)
TVLinkbasestation
2
TVLinkbasestation
Step 1:Connecting the TVLink basestation
To connect the power supply (h):
Place the TVLink basestation next to your TV.
Connect the mini-USB plug of the power supply to
the Power input (“Power”) of the TVLinkbasestation.
Plug the power supply into the wall socket.
2. Installing the Phonak TVLink
(d)
(h)
3
Use the RCA/Cinch cable (i) to connect the TVLink
basestation to the TV:
Connect the 3.5 mm stereo plug to the audio input
(“Audio IN”) of the TVLink basestation.Connect the
red and white RCA/Cinch plugs to the matching
red and white RCA/Cinch output sockets on your TV.
(e)
(i)
2. Installing the Phonak TVLink
4
2. Installing the Phonak TVLink
You can also connect your TVLinkbasestation to the
3.5 mm headset socket of your TV, using the 3.5 mm
audio cable (k):
Connect the 3.5 mm stereo plug to the audio input
of the TVLink basestation (“Audio IN”).
Plug the other end into the headsetoutput socket
of your TV.
(e)
(k)
5
When connecting the TVLink basestation to the
3.5 mm headset socket of your TVyou are able to
adjust the volume via your TV remote control.
ManyTVs will switch off their loudspeakers when
plugging the 3.5 mm jack into the headset socket –
the TV will not be audible for other people. In such
a case use the Cinch/RCA or SCART socket as
described above. For further information on volume
adjustment please refer to step 6 below. The Phonak
TVLink basestation can also be connected to any
other audio source such as an MP3 player, PC or
home sound system using the stereo plug cable (k).
2. Installing the Phonak TVLink
6
Switch on the TVLink basestation by a short press
of the ON/OFFbutton (a) as shown in fig. 1. The
status light(g) will illuminate green initially and
may switch to blue later.
(a)
(g)
Fig. 1
Step2:Switching on
2. Installing the Phonak TVLink
7
Step3:Pairing the TVLink basestation and a headset
Before starting to use the TVLink system,the TVLink
basestation and the headset need to be paired.The
pairing procedure controls which Bluetooth devices
are permitted to communicate with each other.
Pairing needs to be completed only once for each
device youwish to use.
2. Installing the Phonak TVLink
If the TVLink basestation status light(g) is not
flashing blue already, press the ON/OFF button (a)
for 5seconds until the Bluetooth indicator (g)is
fast flashing blue.
Wait untilthe Bluetooth indicator light (g) turns
solid blue. This can take up to 2 minutes but
typically is done within a few seconds.
2. Installing the Phonak TVLink
8
Initiate the pairing process on your headset as
stated in its manual.
9
Step4:Listening to your TV
You will hear the sound of your TV directly in your
Headset.
If you cannothear the sound of your TV through
TVLink please repeat steps 1 to 4 on pages 2 to 9.
The TVLink systemsupports Bluetooth operation up
to arange of 30 m (100 ft). Line-of-sight between your
Headset and the TVLink basestation is not required.
However, interference inthe environment by walls or
furniture may reduce the operating range.
3. Daily usage of the Phonak TVLink
Inhaltsverzeichnis
Andere Phonak Adapter Handbücher
