Phytec PhyCORE-i.MX35 Bedienungsanleitung

A product of a PHYTEC Technology Holding company

phyCORE-i.MX35

HARDWARE MANUAL

EDITION JUNE 2010

phyCORE-i.MX35

PHYTEC Messtechnik GmbH 2010 L-734e_1

In this manual are descriptions for copyrighted products that are not explicitly indicated

as such. The absence of the trademark () and copyright () symbols does not imply

that a product is not protected. Additionally, registered patents and trademarks are

similarly not expressly indicated in this manual.

The information in this document has been carefully checked and is believed to be

entirely reliable. However, PHYTEC Messtechnik GmbH assumes no responsibility for

any inaccuracies. PHYTEC Messtechnik GmbH neither gives any guarantee nor accepts

any liability whatsoever for consequential damages resulting from the use of this manual

or its associated product. PHYTEC Messtechnik GmbH reserves the right to alter the

information contained herein without prior notification and accepts no responsibility for

any damages which might result.

Additionally, PHYTEC Messtechnik GmbH offers no guarantee nor accepts any liability

for damages arising from the improper usage or improper installation of the hardware or

software. PHYTEC Messtechnik GmbH further reserves the right to alter the layout

and/or design of the hardware without prior notification and accepts no liability for doing

so.

Rights - including those of translation, reprint, broadcast, photomechanical or similar

reproduction and storage or processing in computer systems, in whole or in part - are

reserved. No reproduction may occur without the express written consent from PHYTEC

Messtechnik GmbH.

EUROPE NORTH AMERICA

Address: PHYTEC Technologie Holding AG

Robert-Koch-Str. 39

D-55129 Mainz

GERMANY

PHYTEC America LLC

203 Parfitt Way SW, Suite G100

Bainbridge Island, WA 98110

USA

Ordering

Information: +49 (800) 0749832

[email protected] 1 (800) 278-9913

[email protected]

Technical

Support: +49 (6131) 9221-31

[email protected] 1 (800) 278-9913

[email protected]

Fax: +49 (6131) 9221-33 1 (206) 780-9135

Web Site: http://www.phytec.de http://www.phytec.com

1rst Edition June 2010

Contents

PHYTEC Messtechnik GmbH 2010 L-734e_1

1Preface...................................................................................................1

1.1 Introduction.....................................................................................2

1.2 Block Diagram................................................................................4

1.3 View of the phyCORE-i.MX35........................................................5

2Pin Description.....................................................................................7

3Jumpers...............................................................................................21

4Power Requirements..........................................................................26

5Real Time Clock U1 Backup-Voltage................................................27

6System Configuration........................................................................28

6.1 System Startup Configuration ......................................................28

6.1.1 Power-Up-Mode..............................................................28

6.1.2 Boot Mode Select ...........................................................29

7System Memory..................................................................................30

7.1 Memory Model..............................................................................31

7.2 DDR2-SDRAM (U6-U7)................................................................32

7.3 NOR-Flash (U9)............................................................................33

7.4 NAND Flash Memory (U10) .........................................................34

7.5 I²C EEPROM (U2)........................................................................35

7.5.1 Setting the EEPROM Lower Address Bits

(J11, J14, J15)................................................................36

7.5.2 EEPROM Write Protection Control (J1)..........................37

8RS-232 .................................................................................................38

8.1 RS232 Transceiver (U12).............................................................38

8.1.1 UART2 Routing (RN4)....................................................39

9USB......................................................................................................40

9.1 USB-OTG.....................................................................................40

9.2 USB-Host......................................................................................40

10 Ethernet Controller / Ethernet-Phy (U5)...........................................41

11 CAN......................................................................................................42

12 JTAG Interface (X2)............................................................................44

13 Technical Specifications ...................................................................48

phyCORE-i.MX35

PHYTEC Messtechnik GmbH 2010 L-734e_1

14 Hints for Handling the phyCORE-i.MX35 .........................................50

15 The phyCORE i.MX35 on the i.MX Carrier Board............................52

15.1 Concept of the phyCORE-i.MX Development Kits.......................53

15.2 phyMAP-i.MX35............................................................................54

15.2.1 phyMAP-i.MX35 Jumper Settings...................................56

15.2.2 phyMAP-i.MX35 Signal Mapping....................................59

15.2.3 phyMAP-i.MX35 USB-Host Interface..............................66

15.2.4 phyMAP-i.MX35 CAN Interface......................................68

15.2.5 phyMAP-i.MX35 Boot Select Switch...............................70

15.2.6 phyMAP-i.MX35 Mapper Physical Dimensions..............72

15.3 Cooperation of phyCORE-i.MX35 and

phyCORE-i.MX Carrier Board ......................................................73

15.3.1 Power Supply..................................................................74

15.3.2 CAN Interface.................................................................78

15.3.3 Push Buttons and LEDs .................................................80

15.3.4 Keypad Interface.............................................................82

15.3.5 Compact Flash Card.......................................................83

15.3.6 Security Digital Card/ MultiMedia Card...........................84

15.3.7 Audio and Touchscreen..................................................86

15.3.8 USB Host........................................................................88

15.3.9 LCD Connectors.............................................................90

15.3.10 Camera Interface............................................................92

15.3.11 JTAG Interface................................................................95

15.3.12 Complete Jumper Setting List for phyCORE-i.MX35

on the i.MX Carrier Board...............................................97

16 Revision History...............................................................................100

17 Component Placement Diagram.....................................................102

Index..........................................................................................................104

Contents

PHYTEC Messtechnik GmbH 2010 L-734e_1

Index of Figures

Figure 1: Block Diagram of the phyCORE-i.MX35 ......................................4

Figure 2: Top View of the phyCORE-i.MX35 (Controller Side)....................5

Figure 3: Bottom View of the phyCORE-i.MX35 (Connector Side) .............6

Figure 4: Pin-Out of the phyCORE-Connector

(Top View, with Cross Section Insert)..........................................8

Figure 5: Typical Jumper Pad Numbering Scheme...................................21

Figure 6: Jumper Locations (Top View).....................................................22

Figure 7: Jumper Locations (Bottom View) ...............................................23

Figure 8: JTAG Interface at X2 (Top View)................................................44

Figure 9: JTAG Interface at X2 (Bottom View) ..........................................45

Figure 10: Physical Dimensions of phyCORE-i.MX35 Module....................48

Figure 11: phyCORE-i.MX35 Carrier Board Connection Using

the phyMAP-i.MX35....................................................................53

Figure 12: phyMAP-i.MX35 Top View..........................................................54

Figure 13: phyMAP-i.MX35 Bottom View ...................................................55

Figure 14: Jumper Location on PMA-005....................................................56

Figure 15: PMA-005 USB-Host Interface.....................................................66

Figure 16: PMA-005 CAN Interface.............................................................68

Figure 17: PMA-005 Boot Select Dip-Switch...............................................70

Figure 18: Physical Dimensions of phyMAP-i.MX35 Mapper......................72

Figure 19: pyhCORE-i.MX Carrier Board and phyCORE-i.MX35

Power Supply .............................................................................74

Figure 20: phyCORE-i.MX Carrier Board CAN Interface.............................78

Figure 21: phyCORE-i.MX Carrier Board Buttons and LEDs......................80

Figure 22: phyCORE-i.MX Carrier Board Keypad Interface........................82

Figure 23: phyCORE-i.MX Carrier Board SD/MMC Card Interface.............84

Figure 24: phyCORE-i.MX Carrier Board Audio/Touch Interface................86

Figure 25: phyCORE-iMX Carrier Board USB-Host Interface.....................88

Figure 26: phyCORE-i.MX Carrier Board LCD Interfaces...........................90

phyCORE-i.MX35

PHYTEC Messtechnik GmbH 2010 L-734e_1

Figure 27: phyCORE-i.MX Carrier Board Camera Interface .......................92

Figure 28: phyCORE-iMX Carrier Board JTAG Interface............................95

Figure 29: phyCORE-i.MX35 Component Placement (Top View).............102

Figure 30: phyCORE-i.MX35 Component Placement

(Bottom View)...........................................................................103

Contents

PHYTEC Messtechnik GmbH 2010 L-734e_1

Index of Tables

Table 1: Pin-out of the phyCORE-Connector X1........................................9

Table 2: Jumper settings..........................................................................24

Table 3: i.MX35 default power input voltages ..........................................26

Table 4: Basic Boot Modes of i.MX35x Module........................................29

Table 5: Advanced Boot Modes of i.MX35x Module ................................29

Table 6: i.MX35 Memory Map ..................................................................31

Table 7: Compatible NOR Flash Devices.................................................33

Table 8: Compatible NAND Flash Devices ..............................................34

Table 9: U2 EEPROM I²C Address via J11, J14, and J15.......................36

Table 10: EEPROM Write Protection States via J1....................................37

Table 11: RN4 UART2 Signal Routing.......................................................39

Table 12: Fast Ethernet Controller Memory Map.......................................41

Table 13: CAN Controller Memory Map .....................................................42

Table 14: JTAG Connector X2 Signal Assignment ....................................46

Table 15: Jumper Settings of PMA-005......................................................58

Table 16: PMA-005 Mapping List...............................................................59

Table 17: PMA-005 USB-Host Jumper Settings ........................................67

Table 18: PMA-005 CAN Jumper Settings.................................................69

Table 19: x_BOOT3 Selection....................................................................71

Table 20: x_BOOT4 Selection....................................................................71

Table 21: Jumper settings for i.MX35 Power Supply via

Power Plug .................................................................................75

Table 22: Jumper Settings for i.MX35 Power Supply via POE...................76

Table 23: Jumper Settings for i.MX35 Power Supply via Battery...............77

Table 24: CAN2 Interface Jumper Settings................................................79

Table 25: x_BOOT_MODE0 Selection.......................................................81

Table 26: x_BOOT_MODE1 Selection.......................................................81

Table 27: x_Switch .....................................................................................81

phyCORE-i.MX35

PHYTEC Messtechnik GmbH 2010 L-734e_1

Table 28: SD/MMC Interface Jumper Settings for

i.MX35 Module............................................................................85

Table 29: Audio/Touchscreen Interface Jumper Settings for

i.MX35 Module............................................................................87

Table 30: UBS Host Interface Jumper Settings for i.MX35

Module........................................................................................89

Table 31: Camera Interface Jumper Settings for i.MX35 Module ..............93

Table 32: JTAG Jumper Settings for phyCORE-i.MX35 Module................96

Table 33: Jumper Settings for i.MX35 Module on i.MX

Carrier Board..............................................................................97

Preface

PHYTEC Messtechnik GmbH 2010 L-734e_1 1

1Preface

This hardware manual describes the phyCORE-i.MX35 Single Board Computer’s design and function.

Precise specifications for the Freescale i.MX35 microcontrollers can be found in the enclosed

microcontroller Data Sheet/User's Manual.

In this hardware manual and in the attached schematics, active low signals are denoted by a "/" or “#”

preceding the signal name (e.g.: /RD or #RD). A "0" indicates a logic zero or low-level signal, while a

"1" represents a logic one or high-level signal.

Declaration of Electro Magnetic Conformity of the PHYTEC

phyCORE-I.MX35

PHYTEC Single Board Computers (henceforth products) are designed for installation

in electrical appliances or as dedicated Evaluation Boards (i.e.: for use as a test and prototype

platform for hardware/software development) in laboratory environments.

Caution:

PHYTEC products lacking protective enclosures are subject to damage by ESD and, hence, may only

be unpacked, handled or operated in environments in which sufficient precautionary measures have

been taken in respect to ESD-dangers. It is also necessary that only appropriately trained personnel

(such as electricians, technicians and engineers) handle and/or operate these products. Moreover,

PHYTEC products should not be operated without protection circuitry if connections to the product's

pin header rows are longer than 3 m.

PHYTEC products fulfill the norms of the European Union’s Directive for Electro Magnetic Conformity

only in accordance to the descriptions and rules of usage indicated in this hardware manual

(particularly in respect to the pin header row connectors, power connector and serial interface to a

host-PC).

Implementation of PHYTEC products into target devices, as well as user modifications and extensions

of PHYTEC products, is subject to renewed establishment of conformity to, and certification of,

Electro Magnetic Directives. Users should ensure conformance following any modifications to the

products as well as implementation of the products into target systems.

The phyCORE-i.MX35 is one of a series of PHYTEC Single Board Computers that can be populated

with different controllers and, hence, offers various functions and configurations. PHYTEC supports a

variety of 8-/16- and 32-bit controllers in two ways:

(1) as the basis for Rapid Development Kits which serve as a reference and evaluation platform

(2) as insert-ready, fully functional phyCORE OEM modules, which can be embedded directly

into the user’s peripheral hardware design.

PHYTEC's microcontroller modules allow engineers to shorten development horizons, reduce design

costs and speed project concepts from design to market. For more information go to:

http://www.phytec.com/services/phytec-advantage.html

phyCORE-i.MX35

2PHYTEC Messtechnik GmbH 2010 L-734e_1

1.1 Introduction

The phyCORE-i.MX35 belongs to PHYTEC’s phyCORE Single Board Computer module family. The

phyCORE SBCs represent the continuous development of PHYTEC Single Board Computer

technology. Like its mini-, micro- and nanoMODUL predecessors, the phyCORE boards integrate all

core elements of a microcontroller system on a subminiature board and are designed in a manner

that ensures their easy expansion and embedding in peripheral hardware developments.

As independent research indicates that approximately 70 % of all EMI (Electro Magnetic Interference)

problems stem from insufficient supply voltage grounding of electronic components in high frequency

environments the phyCORE board design features an increased pin package. The increased pin

package allows dedication of approximately 20 % of all pin header connectors on the phyCORE

boards to ground. This improves EMI and EMC characteristics and makes it easier to design complex

applications meeting EMI and EMC guidelines using phyCORE boards even in high noise

environments.

phyCORE boards achieve their small size through modern SMD technology and multi-layer design. In

accordance with the complexity of the module, 0402-packaged SMD components and laser-drilled

microvias are used on the boards, providing phyCORE users with access to this cutting edge

miniaturization technology for integration into their own design.

The phyCORE-i.MX35 is a subminiature (85 x 58 mm) insert-ready Single Board Computer populated

with the Freescale i.MX35x microcontroller. Its universal design enables its insertion in a wide range

of embedded applications. All controller signals and ports extend from the controller to high-density

pitch (0.635 mm) connectors aligning two sides of the board, allowing it to be plugged like a "big chip"

into a target application.

Precise specifications for the controller populating the board can be found in the applicable controller

User’s Manual or datasheet. The descriptions in this manual are based on the Freescale i.MX35x. No

description of compatible microcontroller derivative functions is included, as such functions are not

relevant for the basic functioning of the phyCORE-i.MX35.

Inhaltsverzeichnis

Andere Phytec Hauptplatine Handbücher

Phytec

Phytec phyCORE-ADuC812 Bedienungsanleitung

Phytec

Phytec phyCORE-XC161 Bedienungsanleitung

Phytec

Phytec phyBOARD-Wega-AM335x Bedienungsanleitung

Phytec

Phytec phyCORE-P87C591 Programmierhandbuch

Phytec

Phytec phyCORE-MPC5554 Bedienungsanleitung

Phytec

Phytec PCM-995 Bedienungsanleitung

Phytec

Phytec phyCORE-PXA255 Bedienungsanleitung

Phytec

Phytec phyFLEX-i.MX 6 Programmierhandbuch

Phytec

Phytec PhyBOARD-WEGA-AM335 SERIES Bedienungsanleitung

Phytec

Phytec phyBOARD RANA-AM335x Bedienungsanleitung

Phytec

Phytec kitCON-161CS Bedienungsanleitung

Phytec

Phytec phyCARD-M Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX 6 Bedienungsanleitung

Phytec

Phytec phyCORE-LPC2294 Programmierhandbuch

Phytec

Phytec phyCORE-TriCore Bedienungsanleitung

Phytec

Phytec phyCORE-MPC565 Programmierhandbuch

Phytec

Phytec phyBOARD Wega AM335 Series Bedienungsanleitung

Phytec

Phytec phyCORE-LPC2292/94 Bedienungsanleitung

Phytec

Phytec phyCORE-AM335x Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX27 Bedienungsanleitung

Phytec

Phytec phyCORE-LPC3180 Bedienungsanleitung

Phytec

Phytec PhyBOARD-Mira i.MX6 Bedienungsanleitung

Phytec

Phytec phyBOARD-Wega AM335x Bedienungsanleitung

Phytec

Phytec phyBOARD WEGA-AM335x Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Phytec phyCORE-i.MX35 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken