PICOTE Smart Spider DN150/6" Bedienungsanleitung

Operating & Safety Manual

Smart Spider DN150, DN200 & DN225 / 6”, 8” & 9” for 18mm/¾” Shaft

These instrucons are for your personal safety. Always ensure that you

have read and understood these instrucons before using any of the

Smart Spider range.

We now have resellers in the U.S., Europe & Australasia.

Locate your reseller at picotesolutions.com

TOPIC PAGE/S

SAFETY INFORMATION & SYMBOLS 3

AVAILABLE SIZES & POWER SOURCES 5

BILL OF MATERIALS 6

ASSEMBLY & USE 9

PRACTICAL TIPS & SAFETY ADVICE 18

MAINTENANCE & SPARE PARTS 20

WARRANTY POLICY & PROCEDURE 23

To watch practical demonstration videos, or to download an electronic copy of these

Instructions, please visit www.picotesolutions.com. Please note that videos are not

intended as a replacement or alternative to this operating and safety manual, but only

as an additional learning tool.

TABLE OF CONTENTS

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

SAFETY INFORMATION

This section contains important safety information. Failure to

comply could result in serious injury or death.

Safety Symbols

Personal Protective Equipment (PPE)

Always use Personal Protective Equipment when using the Smart Spider and Miller

systems, including suitable overalls / protective clothing & footwear and the following:

Always wear suitable eye protection when using the Smart Spider to prevent

sewage, chemicals or other dust from irritating your eyes.

Always wear suitable ear protection when using the Smart Spider and Miller

systems to prevent any hearing loss.

Always wear suitable cut-resistant gloves when using the Smart Spider to prevent

any hand injuries. Any open injuries or skin irritations should be covered at all

times to avoid contact with sewage, chemicals or dust.

Always wear a suitable ventilation mask when using the Smart Spider or Miller

systems to prevent any resin dust or fumes being inhaled or consumed, which can

cause occupational asthma or dermatitis as well as eye irritation.

Danger risk of serious injury from rotating parts

Danger risk of serious injury, follow instructions

Danger risk of serious injury or death by electrocution, follow instructions

Danger risk of serious injury from hot parts

Safety symbols are used throughout this manual to draw attention to potential hazards.

Danger do not touch. Risk of injury, follow instructions

Danger risk of serious injury or death by electrocution, follow instructions

Dust produced can be dangerous to your health, inflammable or explosive.

Make sure the drain pipe has been opened and ventilated to stop any

gases forming in the lateral drain where the work takes place.

Before assembly, use, replacement of parts or maintenance, unplug the Picote

milling machine or your hand drill from its power socket.

High voltage. Failure to comply may lead to serious injury

including electric shock or injury from rotating parts!

Always remember

Safety Symbols cont.

Safety symbols are used throughout this manual to draw attention to potential hazards.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

ELECTRICAL SET UP REQUIREMENTS FOR MAXI MILLER POWER PLUS

Electrical shock can cause serious or fatal injury. Only qualified personnel

should install, maintain or troubleshoot this equipment.

Picote recommends that a properly trained electrician be available to wire

a power distribution box to whatever power source is available. In the case

where a generator is required, a minimum power requirement of 25,000

KW/KVA 3 Phase 480 volt is necessary.

The Power Plus is a dual voltage 3 phase power configuration. It uses a 10 gauge 4

wire cord.

Be sure the system is properly grounded/earthed before applying power. Do not apply power

before you ensure that grounds are connected. Electrical shock can cause serious or fatal injury.

Follow the National Electrical Code (NEC) and local codes for the safe installation of the

equipment.

Do not operate the Power Plus Miller until you are sure that you are completely familiar with the

safe operation of the machine, all accessories and safety equipment. Improper use can lead to

severe injury. The user manual defines proper use of this equipment.

Contact Picote if you do not understand any procedure or operation concerning this

equipment or the user manual.

READ THE MAXI MILLER POWER+ MANUAL BEFORE USE

AVAILABLE SIZES & POWER SOURCES

The Smart Spider is to a specialty tool for cleaning fragile or damaged pipes. The Smart

Spider can go through pipes which have lost small sections without getting stuck. The

Smart Spider legs adapt to the pipe size when the tool rotates. A Drill Head can be used

if required.

Selecting the correct Smart Spider for the job

Choose your Smart Spider according to the size of the original host pipe.

SMART SPIDER Shaft size

mm/inches

BEND 90° BEND 45°

Smart Spider DN150 / 6” 18 / ¾”YES YES

Smart Spider DN200 / 8” 18 / ¾”YES YES

Smart Spider DN225 / 9” 18 / ¾”YES YES

CHOOSING YOUR POWER SOURCE

The Smart Spider, with the 18mm/¾” diameter shaft, has been designed for and can

ONLY be operated with the Picote Maxi Miller Power+ machine.

The machine should only be connected to a 380-480 Volt (3-phase) power supply.

The power source has to be grounded (earthed).

CHOOSING YOUR DRILL HEAD

The Smart Spider can be used with or without the Drill or Crusher Heads by adding a Hub

Disc. The Drill Head and the Crusher are used when there is blockage in the centre of the

pipe.

If the Smart Spider can fit through the pipe without the Drill Head, the tool should be

used without one. Without the Drill Head all the force is applied to the legs.

BILL OF MATERIALS: DN150/6” Smart Spider

The Smart Hub Disc can be replaced with the Crusher or Drill Head depending on

the working condions.

BILL OF MATERIALS: DN200/8” Smart Spider

The Smart Hub Disc can be replaced with the Crusher or Drill Head.

BILL OF MATERIALS: DN225/9” Smart Spider

The Smart Hub Disc can be replaced with the Crusher or Drill Head.

BILL OF MATERIALS - DN150/6” Smart Crusher

Head

BILL OF MATERIALS - DN200/8” Drill Head

Andere Handbücher für Smart Spider DN150/6"

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PICOTE Pfeifenreiniger Handbücher

PICOTE

PICOTE MAXI MILLER 12/30 Gebrauchs- und Pflegehandbuch

PICOTE

PICOTE MIDI MILLER 12/12 Gebrauchs- und Pflegehandbuch

PICOTE

PICOTE SUPER MIDI 12/20 Gebrauchs- und Pflegehandbuch

PICOTE

PICOTE MAXI MILLER POWER + 18/18 Gebrauchs- und Pflegehandbuch

PICOTE

PICOTE Smart Spider DN150/6" Bedienungsanleitung

PICOTE

PICOTE MINI SMART HEAT MILLER Gebrauchs- und Pflegehandbuch

Beliebte Pfeifenreiniger Handbücher anderer Marken

Virax

Virax VAL 80 Bedienungsanleitung

Ribimex

Ribimex Ribitech PRFDP Betriebsanleitung

General Pipe Cleaners

General Pipe Cleaners Speedrooter 92 S92-450 Bedienungsanleitung

Parkside

Parkside 270382 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners JM-1450 Bedienungsanleitung

Dali

Dali GQ-75 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Gen-Eye SD Bedienungsanleitung

Kompernass

Kompernass 64586 Bedienungsanleitung

Inder

Inder Power P-30 Bedienerhandbuch

Gap Power

Gap Power Speedrooter 92R Bedienungsanleitung

Parkside

Parkside 102800 Betriebsanleitung

General Pipe Cleaners

General Pipe Cleaners Speedrooter XL Bedienungsanleitung

Wöhler

Wöhler DH 420 Bedienungsanleitung

Elliott

Elliott Roto-Jet II Series Handbuch

General Pipe Cleaners

General Pipe Cleaners JM-3055 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners JM-2900 Bedienungsanleitung

Westfalia

Westfalia 82 45 38 Bedienungsanleitung

RIDGID

RIDGID KWIK-SPIN Bedienungsanleitung