Pilotair K25PR Datenblatt

p : 1300 667 579

www.pilotair.com.au

Pilot K25PR Industrial Petrol Reciprocating

INSTRUCTION AND PARTS LIST

MODEL: K25

p : 1300 667 579

www.pilotair.com.au

USER GUIDE

Congratulations on the purchase of a PILOT air compressor. This

unit has been designed to provide reliable and trouble free usage

in servicing your compressed air requirements.

Please take a moment to familiarise yourself with the

information contained in the following sections of this guide

before attempting to operate this unit.

LOCATION OF UNIT

For optimum efficiency locate unit in a clean, dry and cool

environment with good ventilation. Avoid placing obstacles

either on or around unit to facilitate maximum air flow and

cooling.

CHECK OIL LEVEL BEFORE USE IN CASE OF LOSSES

INCURRED DURING SHIPPING

p : 1300 667 579

www.pilotair.com.au

OPERATION

ELECTRIC UNITS

Ensure ON/OFF switch is located on the pressure switch is in an

OFF position (down), before inserting power plug into appropriate

power point and applying power.

Unit can then be switched on using the ON/OFF switch. The

pressure switch will automatically start and stop the compressor

when the air receiver drops below or reaches factory set cut-in

and cut-out pressures respectively.

ALWAYS SWITCH UNIT ON AND OFF VIA

PRESSURE SWITCH TO ENSURE THE UNIT

DOES NOT START AGAINST HIGH PRESSURE

TO PREVENT DAMAGE TO UNIT OR PERSONS DO NOT

ATTEMPT TO MODIFY, BYPASS OR REMOVE PRESSURE

SWITCH OR SAFETY VALVE IN ANY WAY.

“TM” OR “K” SERIES ARE DESIGNED TO OPERATE TO

A MAXIMUM PRESSURE OF 10 BAR.

The air receiver is equipped with a safety valve to release

pressure in the event of a pressure switch cut-out failure. To

prevent damage to the unit, do not attempt to modify, bypass or

remove the pressure switch or safety valve in anyway.

The motor features a manual overload protection (where fitted).

In poor power conditions or motor over temperature conditions,

this overload protector will cut power to the motor. To reset,

wait for the motor to cool then press reset button. If problems

persist, check for power ratings, faulty power or poor

connections.

p : 1300 667 579

www.pilotair.com.au

PETROL /DIESEL DRIVEN UNITS

Please refer to OEM documentation in reference to care and

operation of your petrol/diesel engine.

This unit has been designed to “idle down” to minimum operating

speeds when factory set cut-out pressures are reached. This

saves both fuel consumption and wear on moving parts. When

pressure drops to set cut-in pressures the unit will automatically

resume pumping at normal operating speeds.

To facilitate easy starting of the unit and to ensure no damage to

the electric starter (where fitted) always open the “EASY START”

valve until the unit is operating and then close for normal

operation. This valve is located on the motor/pump platform

(models K25P,K30P) or in the discharge pipe from the pump to

the air receiver (other models).

For Petrol powered units fitted with electric start capability:

Honda Australia recommends the following specification for

wiring to a battery: Max. Cable length: 1.5 M, Cable size: 8

mm/sq. Over 1.5 M in length requires cable size of 15 mm/sq

SAFETY

Pressure vessels (air receivers) are a type of plant,

and as such, MAY be required to be registered with

the relevant statutory authority in your state.

Regulations regarding plant registration vary from

state to state. Check with your relevant government

authority about plant registration.

Compressed air can be dangerous. Never point

compressed air tools or equipment towards another

person.

p : 1300 667 579

www.pilotair.com.au

After use, drain all residual air pressure or engage

outlet tap to prevent accidental discharge by children.

Keep clear of compressor pump during and after

operation. Heat build up in the pump may cause burns

to unwary.

Never operate the unit without factory fitted belt

guard.(belt drive models) or pump shroud (direct drive

models).

Never operate the unit with damaged or exposed

electrical wiring.

Do not alter, adjust or remove any components on the

unit without technical support from Pilot Air or an

authorised Pilot Air agent

Whenever transporting an air compressor, ensure all

air is drained from the air receiver. There should be NO

residual air pressure in the air receiver.

p : 1300 667 579

www.pilotair.com.au

MAINTENANCE INSTRUCTIONS

•Check that fuses or circuit breakers correspond to motor rating. In

case of 415-Volt units, check rotation as indicated by arrow

attached to unit. On 240-Volt units, avoid using extension leads as

they could cause voltage drop and power loss to motor. If extension

is to be used, please follow the table below.

TABLE 1.

KW HP VOLTS RECOMMENDED WIRE SIZE

1.65 2.25 240 HEAVY DUTY, 1.5MM SQUARE WIRE (MAX LENGTH 20 M)

2.20 3.00 240 HEAVY DUTY, 1.5MM SQUARE WIRE (MAX LENGTH 10 M)

•Oil level should be at the centre of the oil sight glass on the

compressor pump. Do not overfill as this could cause excessive oil

being expelled from the crank case breather.

•Oil is to be replaced every 1000 working hours or on a six (6)

monthly basis. Recommended oil:

•PILOT PCO-40G or equivalent (Stationary models).

•PILOT PCO-30G or equivalent (Portable models).

Note: In humid and/or very low duty cycle environments,

condensate may collect in the sump. Under these conditions, it is a

requirement that the operator drain the residual water from the

sump on a regular basis and/or change the oil more frequently than

recommended above.

•Whenever transporting an air compressor, ensure all air is drained

from the air receiver. There should be NO residual air pressure in

the air receiver.

•Routine maintenance should be performed on at least a six (6)

monthly basis.

•Condensation must be drained from air receiver at least weekly.

p : 1300 667 579

www.pilotair.com.au

•Unit must be kept clean to allow proper cooling to take effect.

Special care should be taken to clean the crankcase breather in

order to allow proper crankcase breathing.

•Whenever attempting to carry out any maintenance to compressors,

isolate power and release all pressure from receiver.

•For information regarding spare parts and/or service, please always

quote model and serial number.

•PLEASE KEEP THIS INFORMATION NEAR MACHINE, SO IT CAN BE

READ BY ANYONE ATTEMPTING PREVENTATIVE MAINTENANCE.

DO NOT BOLT COMPRESSOR DIRECTLY ONTO FLOOR. THIS MAY CAUSE

CRACKS IN THE AIR RECEIVER. IF THE COMPRESSOR MUST BE BOLTED,

ENSURE RUBBER VIBRATION PADS ARE IN PLACE AND FASTEN, LEAVING

A GAP BETWEEN BOLT HEAD OR NUT AND COMPRESSOR FOOT TO AVOID

ANY METAL TO METAL CONTACT.

p : 1300 667 579

www.pilotair.com.au

COMPRESSOR COMPONENT DESCRIPTIONS

•PRESSURE SWITCH (240V & 415V models only): This switch is

located on the top of the air receiver and functions as a manual

on/off switch in addition to automatically stopping and starting the

compressor at factory pre-set pressures (electric models only).

•PRESSURE GAUGE: The Pressure Gauge is located on the air

receiver and indicates the pressure held in both PSI and KPA.

•SAFETY VALVE: The Safety Valve is located on the air receiver and

is designed to release pressure in the event of a pressure switch

failure.

•OVERLOAD PROTECTION: Electric models are fitted with an

overload protector, to protect the motor in the event of an over

temperature condition. These reset buttons are located either on

the pressure switch or the motor itself.

•CHECK VALVE (240V & 415V models only): The Check Valve is

located at the junction of the pump discharge pipe and the air

receiver. The check valve prevents air pressure returning from the

air receiver to the pump.

•EASY START VALVE: (Petrol/Diesel models only) The Easy Start

Valve is located on the check valve for portable units and on the

compressor platform for stationary units. This valve should be

opened for ease of starting of the engine and closed when running

for normal operation.

•RECEIVER DRAIN: The Receiver Drain is located at the underside of

the air receiver and is used for draining condensate from the

receiver.

•OIL SIGHT GLASS: The Oil Sight Glass is located on the side of the

compressor pump (opposite the flywheel) and is used for examining

the oil level of the unit.

p : 1300 667 579

www.pilotair.com.au

K25 PUMP

p : 1300 667 579

www.pilotair.com.au

Pos Component MU Multiplier

$33104600

CASING

1,0

$31604730SGL

CYLINDER

1,0

SG61400

HEAD

1,0

SG61200

SHAFT

1,0

9434M01

AIR FILTER ASSEMBLY

1,0

$30400830

FRONT COVER

1,0

$30400860

CASING REAR SUPPORT

1,0

$31003080

FLYWHEEL

1,0

$30300030

BALL BEARING 6205 K8-K28

2,0

$36531150

OIL LIGHT

1,0

$36507050

OIL PLUG

1,0

$30300040

SEAL

1,0

$37400720

SCREW FLYWHEEL

1,0

$37500730

WASHER FLYWHEEL

1,0

417

$36531140

OIL PLUG

1,0

900

9434A12

MPK VALVE PLATE K25

1,0

901

9434B16

MPK PISTON-CONROD K25

1,0

908

9434E08

MPK AFTERCOOLER K17-18-25

1,0

909

9434F13

MPK GASKET K25

1,0

912

9434C15

MPK PISTON RINGS K25

1,0

921

9434D02

MPK INTERCOOLER K25-28

1,0

922

9434H05

MPK MAINTEN.PV K25

1,0

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere pilotair Luftkompressor Handbücher

pilotair

pilotair TM300I Datenblatt

pilotair

pilotair K25 Datenblatt

pilotair

pilotair TRADEMASTER Series Datenblatt

pilotair

pilotair K50 Datenblatt

pilotair

pilotair K25L18 Datenblatt

pilotair

pilotair TM325I Datenblatt

pilotair

pilotair K25-Vi Datenblatt

pilotair

pilotair SILENT Series Gebrauchsanweisung

pilotair

pilotair Hobby Oil Free Series Bedienungsanleitung

pilotair

pilotair K25 Datenblatt

pilotair

pilotair K30-Vi Datenblatt

pilotair

pilotair K17 Datenblatt

pilotair

pilotair K25SDL Bedienungsanleitung

pilotair

pilotair K Series Datenblatt

pilotair

pilotair DCR 1311 Gebrauchsanweisung

pilotair

pilotair K30 Datenblatt

pilotair

pilotair SCR Series Datenblatt

pilotair

pilotair Hobby Series Bedienungsanleitung

pilotair

pilotair K17 Datenblatt

pilotair

pilotair K25D Datenblatt

pilotair

pilotair PAC Series Leitfaden

pilotair

pilotair K25P Datenblatt

pilotair

pilotair K30D Datenblatt

pilotair

pilotair ALTA-TEC Series Leitfaden

Beliebte Luftkompressor Handbücher anderer Marken

Sparmax

Sparmax DC-25XR Bedienungsanleitung

KAESER

KAESER M122 Bedienungsanleitung

GMC

GMC GAC1500 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton Air Compressor Bedienungsanleitung

Fini

Fini F3GST2TK Bedienungsanleitung

Industrial Air

Industrial Air CP1580325 Programmierhandbuch

Campbell Hausfeld

Campbell Hausfeld RP3300 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Bedienungsanleitung

Hitachi

Hitachi EC99S Bedienerhandbuch

Parkside

Parkside PKO 270 A1 Bedienungsanleitung

Sullair

Sullair 185 Bedienungsanleitung

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Bedienungsanleitung

Ferm

Ferm CRM1046 Bedienungsanleitung

BE AC153 Bedienungsanleitung

RIDGID

RIDGID OF25150A Bedienungsanleitung

Johnson Controls

Johnson Controls QUANTUM LX Handbuch

Sears

Sears Craftsman 919.167463 Bedienungsanleitung

Ring Automotive

Ring Automotive RAC700 Bedienungsanleitung

pilotair K25PR Datenblatt

Beliebte Luftkompressor Handbücher anderer Marken