Pima Hunter-pro Bedienungsanleitung

HUNTER-PRO

Intruder Alarm System

User Manual

P/N 4410066 Rev. D (Jan-2004)

PIMA Electronic Systems Ltd.

5 Hatzoref Street, Holon 58856, Israel

℡

+972-3-5587722



+972-3-5500442



support@pima-alarms.com



http://www.pima-alarms.com

PIMA Electronic Systems Ltd. does not represent that its Product may not be compromised

and/or circumvented, or that the Product will prevent any death, personal and/or bodily injury

and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the

Product will in all cases provide adequate warning or protection. The User understands that a

properly installed and maintained equipment may only reduce the risk of events such as

burglary, robbery, and fire without warning, but it is not insurance or a guarantee that such

will not occur or that there will be no death, personal damage and/or damage to property as a

result.

PIMA Electronic Systems Ltd. shall have no liability for any death, personal and/or bodily

injury and/or damage to property or other loss whether direct, indirect, incidental,

consequential or otherwise, based on a claim that the Product failed to function.

Warning:

The user should follow the installation and operation instructions and among other

things test the Product and the whole system at least once a week. For various reasons,

including, but not limited to, changes in environment conditions, electric or electronic

disruptions and tampering, the Product may not perform as expected. The user is advised to

take all necessary precautions for his/her safety and the protection of his/her property.

This document may not be duplicated, circulated, altered, modified, translated, reduced to any

form or otherwise changed, unless PIMA’s prior written consent is granted.

All efforts have been made to ensure that the content of this manual is accurate. Pima retains

the right to modify this manual or any part thereof, from time to time, without serving any prior

notice of such modification.

Please read this manual in its entirety before attempting to program or operate your system.

Should you misunderstand any part of this manual, please contact the supplier or installer of

this system.



You can contact us at:

PIMA Electronic Systems Ltd.

5 Hatzoref Street, Holon 58856, Israel

http://www.pima-alarms.com

HUNTER-PRO Intruder Alarm System - User Manual

Table of Contents

Chapter 1 Introduction ................................................................................ 5

1.1

Main Features of the HUNTER-PRO ...................................................5

1.2

Operating Codes ................................................................................6

Chapter 2 Keypads and the Remote-Control................................................... 9

2.1

Introduction .......................................................................................9

2.2

Keypads Description ..........................................................................9

2.2.1

Zone Statues Codes.......................................................................10

2.2.2

System Status Codes......................................................................11

2.3

List of Key Functions ........................................................................11

2.4

Outdoor Anti-Vandal Keypad ...........................................................12

2.5

The Remote Control .........................................................................13

Chapter 3 System Functions ....................................................................... 15

3.1

Arming and Disarming .....................................................................15

3.1.1

Auto Arming .................................................................................16

3.1.2

Zone Bypass .................................................................................17

3.1.3

Bypass Entry Countdown ..............................................................18

3.1.4

Alarms ..........................................................................................18

3.2

Chime ..............................................................................................18

3.3

Panic................................................................................................19

3.4

Onboard Relay.................................................................................19

3.5

Keypad Buzzer .................................................................................20

3.6

System Self-Test................................................................................20

3.7

View History Log..............................................................................20

3.8

Programming....................................................................................21

3.8.1

Codes ...........................................................................................21

3.8.2

Entering Names.............................................................................25

3.8.3

Private Telephone Numbers

............................................................25

3.8.4

Time and Date ..............................................................................28

3.9

Telephone Remote Controlling.........................................................28

3.10

Partitions ..........................................................................................29

HUNTER-PROIntruder Alarm System-User Manual

Chapter 4 Troubleshooting ........................................................................ 30

4.1

Troubleshooting ...............................................................................30

4.2

Wireless Detectors for Walk-Test......................................................31

4.2.1

Wireless Event Histories................................................................32

4.3

Code Related Problems ....................................................................33

HUNTER-PRO Intruder Alarm System - User Manual

Chapter

Introductio

Congratulations on your purchase of the HUNTER-PRO Intruder Alarm System. Much care

has been taken in developing the HUNTER-PRO Intruder alarm system, which will provide

you with unprecedented peace of mind. The HUNTER-PRO’s user-friendly operation and

advanced features will professionally protect your home or business.

It is important to familiarize yourself with the HUNTER-PRO Intruder Alarm System in

order to take full advantage of the complete range of the HUNTER-PRO’s features. To

assure optimum safety and security, you should test the HUNTER-PRO Intruder Alarm

System once a week.

The HUNTER-PRO Intruder Alarm System offers a choice of different keypad models. All but one

(RX-200) are equipped with a Liquid Crystal Display (LCD). For complete instructions on

operating, accessing, and programming your HUNTER-PRO Intruder Alarm System, using the

supplied keypad model, please turn to the appropriate chapter as listed below:

For operating and programming with all

LCD

Keypad Models (i.e.,RX-150, RX-160

, and

RX-400, RX-410)

, see sections

2.2 to

2.3.

For operating with

Keypad Model RX-200 (Anti-Vandal)

, see section

2.4

1.1

Main Features of the HUNTER-PRO

8to 16 zones plus two Tamper zones

Dials on alarms to four private telephone numbers, plus one

“Follow Me” number

NOTE:

The HUNTER-PRO dials first to the monitoring station (If you are connected to a

monitoring station), then, it dials the private telephone numbers as programmed.

You can program the private numbers (refer to section

3.8.3), while only the

technician can program the telephone numbers to the monitoring stations.

Various ways to arm and disarm the system: keypad, key, remote

control, touch-tone telephone

HUNTER-PROIntruder Alarm System-User Manual

Two families of keypads: Internal keypads such as the RX-150, RX-160, RX-400, and

RX-410 and weather and vandal-Proof keypad (RX-200) for outdoor installation

Connects up to eight different keypads

Choice of arming modes: Full, Home1, and Home2

Up to 16 partitions, each one with its own user code

Up to 410 System Events in history log (memory)

A variety of operating codes: Master Code, up to 16 User Codes,

Short Code, Duress Code (used during a hold up), and Relay

Activation Code (e.g., to operate an electric gate)

Automatic arming (time and/or motionless programming)

Remote control via touch-tone telephone

Temporary manual and/or automatic bypass of zones

“Chime” mode per zone: activates the keypad buzzer when a zone

is opened (e.g., to monitor a back door when system is disarmed)

Double communication to Monitoring Stations by telephone and

Long-Range VHF/UHF Radio Transmitter

Connection to a local printer to print all events

Connection to an external PIMA output card to activate auxiliary

devices such as video cameras etc.

Enabled for expansion (zone doubling, wireless, etc.)

Enabled to use two End Of Line resistors that will further secure the

alarm system against SHORT and CUT

Enabled to operate with up to 16 wireless detectors (add-on)

1.2 Operating Codes

You have five code types with which you can control different functions of the

HUNTER-PRO:

Master Code

Use this code to access various programming

options. The default factory

Master Code

5555

. For safety

reasons, we recommend not to use this Code to arm or disarm the

system.

IMPORTANT!

We recommend that you change the default factory Master Code as soon as you

start to use your new alarm system.

User Code

You can program up to 16 different user codes to arm

and disarm the system.

HUNTER-PRO Intruder Alarm System - User Manual

NOTES:

You can program a name for each user code. This user name will appear when

viewing the ‘history log.’

Short Code

A two-digit code with which you can ONLY arm the

system.

Hold-Up Code

(Duress Code): This code is ONLY for disarming the

system during a robbery, but is useful ONLY if the system is

connected to a Monitoring Station.

Relay Code

: Use this code to change the status of the control

panel’s internal relay from ON to OFF and vise versa. The relay

can be used for various applications (e.g., opening/closing an

electric gate, opening an electromagnetic door lock, etc.).

NOTES:

The letter R is displayed to the left of the clock when the relay is ON.

The installer programs the time in which the relay is ON.

The relay can also be programmed by the installer to be activated as response to

a zone alarm and/or system failure.

HUNTER-PROIntruder Alarm System-User Manual

Empty Page

HUNTER-PRO Intruder Alarm System - User Manual

Chapter

Keypads and th

Remote-Contr

2.1 Introduction

You have a choice of keypad models with Liquid Crystal Display (LCD) that you can

connect to the HUNTER-PRO. All the keypads are identical in functionality and have a

display with two rows of 16 characters on each row. The keypads vary only in design and

size of display. The instructions in this manual refer to the RX-410. However, all the

functions and operations are identical to all the keypads.

The keypads are used to control and program the system. Each button on the keypads has

a specific function as describes either on or above the appropriate key.

Every programming action begins with entering the master code after which the

display will show:

Select: OFF

NOTE:

You can only program the system when it is disarmed (on display:

Select:OFF

)

From this point on each key functions according to what is written above it;

telephone, code, chime, etc.

2.2 Keypads Description

These are the available LCD keypad models:

RX-150 RX-160 RX-400 RX-410

HUNTER-PROIntruder Alarm System-User Manual

Keypads – Essential Features

Fault Notification:

The red FAULT light

blinks when a fault

is detected. A

description of the

fault appears in the

display.

Clock Display:

The time (based

on a 24 hour

clock) is shown in

the upper right

area of the

display.

Fault

Description:

The Fault

description

shown in this

sample display

indicates a

battery failure.

17 18 19 20 21 22 23 24 25 26 27 2 8 29 3 0 31 32

12345678910111213141516

Armed Indicator:

The green

ARMED

light provides the

system arm status

as follows:



Off:

System is

Disarmed.



On:

The alarm

system is in Arm

mode.



Blinking:

The

system is in Entry

or Exit Delay

Time Mode.

Zone Status:

The status of

each zone is

listed under its

number (see

table below for

further zone

statuses).

System Status Codes:

"A" indicates system is in Auto-Arm mode

2.2.1

Zone Statues Codes

The following zone status symbols appear in the display:

Symbol Status

Closed Zone

Open Zone

Bypassed Zone

Alarm was triggered while system was armed

Chime Zone

Faulty Zone (disconnected wires)

Low battery level

Armed zone in a partitioned system

Short Zone (short in wires)

Supervision signal not received from the detector; Indication accompanied by a

“Wireless Detector” failure indication

WrlssRec

on display, including time)

Armed partition

Andere Handbücher für hunter-pro

Inhaltsverzeichnis

Andere Pima Sicherheitssystem Handbücher

Pima

Pima Hunter-Pro 832 Bedienungsanleitung

Pima

Pima HUNTER-PRO RSA Bedienungsanleitung

Pima

Pima Hunter-Pro Series Bedienungsanleitung

Pima

Pima Captain 6 Bedienungsanleitung

Pima

Pima HUNTER-PRO 32 RXN-9/416 Bedienungsanleitung

Pima

Pima HUNTER-PRO 896 Bedienungsanleitung

Pima

Pima FORCE Series Bedienungsanleitung

Pima

Pima FORCE Bedienungsanleitung

Pima

Pima Captain 6 Bedienungsanleitung

Pima

Pima CAPTAIN-i 4410061 Bedienungsanleitung

Pima

Pima Hunter-Pro 32 Bedienungsanleitung

Pima

Pima hunter-pro Bedienungsanleitung

Pima

Pima Sentinel Bedienerhandbuch

Pima

Pima RPB Bedienungsanleitung

Pima

Pima FORCE Betriebsanleitung

Pima

Pima SRO743 Technische Daten

Pima

Pima FORCE Series Bedienungsanleitung

Pima

Pima SRO143 Bedienungsanleitung

Pima

Pima VISION Bedienungsanleitung

Pima

Pima AlarmView Bedienungsanleitung

Pima

Pima Captain 8 Hunter-Pro 832 Bedienungsanleitung

Pima

Pima hunter-pro Konfigurationshandbuch

Pima

Pima Hunter-Pro Series Bedienungsanleitung

Pima

Pima HUNTER-PRO RXN-9 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung