Pinnacle 1830 Series Bedienungsanleitung

When assembling or installing

this product wear protective

gloves and eyewear.

SAFETY TIP:

200kg

PER SHELF

For evenly spaced shelves (from bottom shelf): 12 Free Keyholes, 11 Free Keyholes, 12 Free Keyholes,

11 Free Keyholes.

SERIES >>

Very Important: Unpack the unit and conﬁrm that you have all the parts listed. Assemble the unit on

a solid, level surface. Avoid carpet. You will need the assitance of a second person during assembly.

Safety tip: For added safety and support we recommend you ﬁx unit to a wall.

You will need the following: Rubber Mallet.

Please note: When moving shelving unit lift using the bottom leg uprights.

Parts List Step 1 Step 2

Step 5

Step 6 Step 7

Step 4Step 3

MDF Shelves x5

Brackets ‘A x10

Brackets ‘B’ x10

Braces ‘C’ x10

Legs ‘D’ x8

Connector Pins x4

Foot End Caps x8

NOT TO SCALE

Place foot end caps onto the bottom of the legs ‘D’.

Note upright position. Place bracket ‘A’ onto the

legs ‘D’. A rubber mallet can be used to lightly tap

all brackets into the keyholes on the legs.

Use shelf bracket ‘B’ for the side brackets using

the bracket ‘A’ from Step 1 as a guide for height.

Use same shelving brackets for opposing sides as

shown in the diagram. Place brace ‘C’ as shown.

Fix remaining brackets to your desired height.

Ensure that braces ‘C’ are ﬁxed to all shelves.

Place the MDF boards in the shelves. Ensure that they are sitting ﬂush against the

edge of the shelf brackets.

PLEASE NOTE: Refer to next page for attaching the provided Tip-over prevention kit.

Join the upper legs to the lower legs ‘D’ with the

connector pins. Note: The legs are designed to sit

directly on top of each other - do not overlap

them. Handy Hint: Flathead screwdriver may be

used to tap in connector pins.

Fix brackets ‘B’ and ‘A’ to the top of legs ‘D’.

Note: MDF shelf should sit ﬂush with the top of

legs ‘D’.

Place MDF board on bottom shelf to minimise

buckling. Fix brackets ‘B’ so that top rivet sits on

the upper legs and the bottom rivets sit on the

lower legs. Repeat with brackets ‘A’, followed by

braces ‘C’ as shown.

WARRANTY CONDITIONS: Any claim under this warranty must be made within 1 year of the date of purchase of the product. To make a claim under this warranty, take the product (with proof of purchase) to any

Bunnings store (for AUS customers see www.bunnings.com.au and for NZ customers see www.bunnings.co.nz for store locations). Pinnacle Hardware bears reasonable, direct expenses of claiming under the

warranty. You may submit details and proof of purchase to our support centre for consideration. The warranty covers manufacturer defects in materials, workmanship and ﬁnish under normal use. This warranty is

provided in addition to other rights and remedies you may have under law: Our goods come with guarantees that cannot be excluded under the Australian consumer law or Consumer Guarantees Act 1993 (NZ). You are

entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major failure. This warranty excludes damage resulting from product misuse or product neglect, any modiﬁcations, additions or alterations to the product

including the addition of extra shelves. Additions or modiﬁcations can compromise the structure and safety of the product. The warranty covers domestic use only and does not apply to commercial applications. This

warranty is given by Pinnacle Hardware, ABN 87 614 496 196, 28 Hudson Court, Keysborough Vic 3173, 1800 349 776, Email: [email protected]. Products sold in New Zealand are imported by Bunnings New