PIONEER DJ TSP-16 Bedienungsanleitung

ORDER NO.

Pioneer DJ Corporation 6F, Yokohama i-Mark Place, 4-4-5 Minatomirai, Nishi-ku, Yokohama, Kanagawa 220-0012 Japan

2016 Pioneer DJ Corporation

TSP-16

QRT1001

PROFESSIONAL SAMPLER

TSP-16

THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

THIS SERVICE MANUAL SHOULD BE USED TOGETHER WITH THE FOLLOWING MANUAL(S).

Model Type Power Requirement Remarks

TSP-16 SYXJ AC 100 V to 240 V

TSP-16 UXJCB AC 100 V to 240 V

TSP-16 AXJ AC 100 V to 240 V

Model Order No. Remarks

TSP-16 QRT1002 SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM, PCB PARTS LIST

2TSP-16

12 3 4

SAFETY INFORMATION

WARNING

This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive

harm.

Health & Safety Code Section 25249.6 - Proposition 65

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-

yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained

to properly and safely repair complex products such as those covered by this manual.

Improperly performed repairs can adversely affect the safety and reliability of the product and may

void the warranty. If you are not qualified to perform the repair of this product properly and safely, you

should not risk trying to do so and refer the repair to a qualified service technician.

TSP-16

56 7 8

CONTENTS

SAFETY INFORMATION.......................................................................................................................................................... 2

1. SERVICE PRECAUTIONS .................................................................................................................................................... 4

1.1 NOTES ON SOLDERING ............................................................................................................................................... 4

1.2 NOTES ON REPLACING ............................................................................................................................................... 4

1.3 SERVICE NOTICE.......................................................................................................................................................... 4

2. SPECIFICATIONS................................................................................................................................................................. 5

2.1 ACCESORIES ................................................................................................................................................................ 5

2.2 SPECIFICATIONS .......................................................................................................................................................... 5

3. BASIC ITEMS FOR SERVICE .............................................................................................................................................. 6

3.1 CHECK POINTS AFTER SERVICING ........................................................................................................................... 6

3.2 JIGS LIST ....................................................................................................................................................................... 6

3.3 PCB LOCATIONS ........................................................................................................................................................... 7

4. BLOCK DIAGRAM ................................................................................................................................................................ 8

4.1 OVERALL WIRING DIAGRAM ....................................................................................................................................... 8

4.2 SIGNAL BLOCK DIAGRAM............................................................................................................................................ 9

4.3 POWER BLOCK DIAGRAM ......................................................................................................................................... 10

4.4 MATRIX TABLE............................................................................................................................................................. 11

5. DIAGNOSIS ........................................................................................................................................................................ 15

5.1 STARTUP SEQUENCE ................................................................................................................................................ 15

5.2 TROUBLESHOOTING.................................................................................................................................................. 16

Starting Trouble.......................................................................................................................................................... 16

Display Trouble .......................................................................................................................................................... 17

Operation Trouble ...................................................................................................................................................... 18

Audio Trouble ............................................................................................................................................................. 19

Interface Trouble ........................................................................................................................................................ 22

Other Trouble ............................................................................................................................................................. 23

5.3 VOLTAGE MONITORING CIRCUIT .............................................................................................................................. 24

5.4 PIN ASSIGNMENT LIST .............................................................................................................................................. 25

6. SERVICE MODE ................................................................................................................................................................. 39

6.1 TEST MODE................................................................................................................................................................. 39

6.2 ABOUT THE DEVICE................................................................................................................................................... 46

7. DISASSEMBLY ................................................................................................................................................................... 47

8. EACH SETTING AND ADJUSTMENT ................................................................................................................................ 57

8.1 NECESSARY ITEMS TO BE NOTED........................................................................................................................... 57

8.2 UPDATING OF THE FIRMWARE ................................................................................................................................. 58

9. EXPLODED VIEWS AND PARTS LIST............................................................................................................................... 59

9.1 PACKING SECTION ..................................................................................................................................................... 59

9.2 EXTERIOR SECTION .................................................................................................................................................. 61

9.3 PANEL SECTION (1/2) ................................................................................................................................................. 63

9.4 PANEL SECTION (2/2) ................................................................................................................................................. 65

9.5 CHASSIS SECTION ..................................................................................................................................................... 67

4TSP-16

12 3 4

1. SERVICE PRECAUTIONS

1.1 NOTES ON SOLDERING

1.2 NOTES ON REPLACING

1.3 SERVICE NOTICE

• For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.

Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs

accompanied by reworking of soldering.

Do NOT use a soldering iron whose tip temperature cannot be controlled.

The part listed below is difficult to replace as a discrete component part.

It the failure of suspected that are listed in the table, replace whole ASSY.

Parts that is Difficult to Replace

ASSY Name Ref No. Part No. Function Remarks

IC201 MM3543BH DC/DC CONVERTER IC with heat-pad

IC202 MM3543BH DC/DC CONVERTER IC with heat-pad

IC501 NJW4155GM1-A DC/DC CONVERTER IC with heat-pad

IC502 MM3543BH DC/DC CONVERTER IC with heat-pad

IC502 TPS2557DRB USB POWER SW IC with heat-pad

IC800 MMPF0100F0AEP POWER MANAGEMENT IC IC with heat-pad

IC2000 MCIMX6Q5EYM10AD MAIN uCOM BGA

IC2300 K4B4G1646D-BCMA DDR3-RAM BGA

IC2301 K4B4G1646D-BCMA DDR3-RAM BGA

IC3800 THGBMHG6C1LBAWL eMMC BGA

S200 ASG1102 POWER SW Terminal part with through-hole

Terminal part with through-hole

JA2600 AKN7115 LAN TERMINAL (RJ-45)

JA3200 DKN1188 MIDI IN TERMINAL (DIN) Terminal part with through-hole

JA3201 DKN1188 MIDI OUT/THRU TERMINAL (DIN) Terminal part with through-hole

MAIN ASSY

JA4100 DKN1237 USB-B TERMINAL Terminal part with through-hole

IC5400 AK4458VN MULTI-OUT DAC IC with heat-pad

IC6000 AK4452VN SEND DAC IC with heat-pad

IC6600 AK4452VN HEADPHONE DAC IC with heat-pad

IO ASSY

VR5200 DCS1133 INPUT LEVEL VOLUME

Terminal part with through-hole

MVR ASSY VR6800 DCS1134 MAIN OUT VOLUME

USBA ASSY JA7600 JA7600 USB-A TERMINAL Terminal part with through-hole

Terminal part with through-hole

IC7100 R1290K103A DC/DC CONVERTER IC with heat-pad

IC7101 BD81A04EFV-M DC/DC CONVERTER IC with heat-pad

LCD ASSY

S9321 DSX1080 ROTARY SELECTOR (ENCODER)

CDC ASSY IC7700 AD7147ACPZ500RL7 CDC (CAPACITANCE SENSORSIC) IC with heat-pad

• Performance pad was calibrated when the product is produced. If a relevant part is replaced with a new one, be sure to

carry out the calibration.

• For the method of calibration, refer to "PAD CALIBRATION MODE" in "6.1 TEST MODE".

• If you forget to carry out the calibration, power for tapping the performance pad and degree of sound volume when

the sampler velocity mode is turned ON vary depending on the pad.

• Calibration execution data is memorized in the MAIN ASSY. Be sure to carry out the calibration when the MAIN ASSY is

replaced new one.

Calibration of performance pad

• Don`t touch the black parts of the PADB ASSY (side-A) and black mat parts of the Sensor (16 pieces each, which are

pressure sensitive ) with your bare hands.

Clear the dust between the PADB ASSY, Sheet, Sensor and Button (DEB2037) by air blast when you assemble the sensor.

About PADB ASSY of sensors (Pressure sensitive)

• Clear the dust between inside of the Cap, Buttons and PCBs by air blast to remove the foreign particles when you assemble

SEQ1 ASSY, SEQ2 ASSY or BAR ASSY.

Caution: Control Panel and Chassis unit in the state that has wire does not open 180 degrees.

About SEQ1 ASSY, SEQ2 ASSY and BAR ASSY

• Replacement of the NAND (IC2601) in the MAIN ASSY is not possible during service, because writing of the MAC address

on the production line is required. Therefore, the NAND (IC2601) are not supplied as a service part. If the NAND is defective,

replace the whole MAIN ASSY.

About the NAND:Flash ROM IC(IC2601) in the MAIN ASSY

TSP-16

56 7 8

2. SPECIFICATIONS

2.1 ACCESORIES

2.2 SPECIFICATIONS

• AC adapter (DRW1553)

•Power cord (SYXJ : ADG1154)

(UXJCB : XDG3052)

•USB cable (DDE1128)

(AXJ : ADG7079)

(AXJ : DRH1361)

• LAN cable (DDE1141)

• Operating instructions

(Quick start guide)

(SYXJ : DRH1360)

(UXJCB : DRH1359)

•Software license notice (SYXJ : DRH1390, DRH1391)

(UXJCB : DRH1390, DRH1391)

• Warranty card (

(AXJ : DRH1403)

SYXJ : DRY1270)

AC adapter

Power............................................................ AC 100 V to 240 V, 50 Hz/60 Hz

Rated current ......................................................................................... 0.9 A

Rated output ............................................................................... DC 12V, 3A

Power consumption (standby) ............................................................. 0.5 W

General – Main Unit

Power consumption .................................................................. DC 12 V, 2A

Main unit weight ....................................................................... 3.2 kg (7.1 lb)

Max. dimensions .................... 436.5 mm (W) × 74.3 mm (H) × 261.2 mm (D)

(17.2 in. (W) × 10.3 in. (H) × 16.2 in. (D))

Tolerable operating temperature............... +5 °C to +35 °C (+41 °F to +95 °F)

Tolerable operating humidity............................ 5% to 85% (no condensation)

Audio Section

Sampling rate.................................................................................... 44.1 kHz

A/D converter ......................................................................................... 24-bit

D/A converter ......................................................................................... 32-bit

Frequency response.............................................................. 20 Hz to 20 kHz

S/N ratio (rated output) 1..................................................................... 112 dB

Total harmonic distortion 1................................................................ 0.002 %

INPUT

Max. input level .......................................................................... +16 dBu

Input impedance ............................................................................. 33k Ω

OUT1-2/MASTER/ASSIGNABLE OUT

Rated output level / Load impedance ...............................

+16 dBu/10k Ω

Output impedance ......................................................................... 680Ω

+16 dBu/10k Ω

680Ω

OUT3-8/ASSIGNABLE OUT

Rated output level / Load impedance ...............................

Output impedance ...........................................................................

PHONES

Rated output level / Load impedance .................. 100 mW+100 mW/32Ω

Input / Output terminals

INPUT terminals

1/4” TSjack ............................................................................................ x2

OUT1-2/MASTER/ASSIGNABLE OUT terminals

1/4” TSjack ............................................................................................ x2

OUT3-8/ASSIGNABLE OUT terminals

1/4” TSjack ............................................................................................ x6

PHONES terminals

1/4” stereo phone jack .......................................................................... x1

USB terminals

A type..................................................................................................... x1

Power supply ... 5 V/500 mA or less

B type..................................................................................................... x1

LINK terminal

LAN terminal (100 Base-TX) ................................................................. x1

MIDI IN terminal

5-pin DIN ............................................................................................... x1

MIDI OUT/THRU terminals

5-pin DIN ............................................................................................... x1

1 When TRACK TYPE is SAMPLE

The specifications and design of this product are subject to change

without notice.

6TSP-16

12 3 4

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING

3.2 JIGS LIST

1 Check the firmware version in Test mode. The version of the firmware must be latest.

Update firmware to the latest one, if it is not the latest.

2Confirm whether the customer complain has

been solved.If the problem pointed out by the

customer occurs with a specific source or

operation, input that specific source then perform

that specific operation for checking.

The customer complain must not be reappeared.

Audio and operations must be normal.

3Check the analog audio input. Audio and operations must be normal.

4 Check the analog audio output. Audio and operations must be normal.

6 Check the FL display and LEDs. Check that all LEDs light in Test mode.

8 Check the LCD display. Check that there is no dirt or dust trapped inside the LCD display.

9 Check the touch panel. Check whether a product can be opeated properly in an all-back screen.

7 Check the connection of each interface

USB A

USB B

LAN

MIDI

5Check the each operation.

(SW, VR and PAD etc.)

Make sure that all operations function properly in Test mode.

Check the appearance of the product.

No scratches or dirt on its appearance after receiving it for service.

*1 : IP address of this product “6.1 TEST MODE PAGE 8 : DEVICE TEST ” can be

comfirmed .

To keep the product quality after servicing, confirm recommended check points shown below.

Distortion

Noise

Volume too low

Volume too high

Volume fluctuating

Sound interrupted

See the table below for the items to be checked regarding audio.

Item to be checked regarding audio

No. Procedure Check points

Connect the USB memory and check the file by browsing.

Connect the PC and make sure you can access internal memory in Mass storage mode.

Connect the PC and check the communication with Ping command.*1

IN-OUT loop connected with MIDI cables, operation check in Test mode.

Jigs List

Jig Name Part No. Purpose of use / Remarks

USB cable GGP1193For PC connection

PAD calibration weighting jig GGF1685 Used for weighting at PAD calibration

Weight: 150g ± 5g

Diameter of bottom surface: ø10 and plain surface

(If consistent in the above-mentioned conditions, available)

TSP-16

56 7 8

3.3 PCB LOCATIONS

DSF ASSY

PARA ASSY

LCD ASSY

STBY ASSY

TFT LCD &

To u c h P a n e l

MAIN ASSY

MODE ASSY

MVR ASSY

IO ASSY

CDC ASSY

PADB ASSY

SEQ1 ASSY

SEQ2 ASSY

BAR ASSY

USBA ASSY

• Control Panel Section

• Chassis Section

Front

∗∗

∗Note :

The 1 and 2 ASSYs of SYQ* ASSYs have the same

circuitry, parts, and board shapes.

Only printed information is different, because their part

numbers and wiring numbers are different.

They are handled similarly in their production management.

Therefore, either 1 or 2 ASSY of the respective ASSYs is

assembled in the respective place.

• Top view

• Bottom view

NOTES: Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.

The mark found on some component parts indicates the importance of the safety factor of the part.

Therefore, when replacing, be sure to use parts of identical designation.

Mark No. Description Part No.

LIST OF ASSEMBLIES

1..MAIN ASSY DWX3864

NSP 1..AUDIO ASSY DWM2616

2..IO ASSY DWX3865

2..MVR ASSY DWX3866

2..USBA ASSY DWX3868

1..LCD ASSY DWX3867

NSP 1..PAD ASSY DWM2618

2..PADB ASSY DWX3869

2..SEQ1 ASSY DWX3870

2..SEQ2 ASSY DWX3871

2..BAR ASSY DWX3872

2..CDC ASSY DWX3873

2..MODE ASSY DWX3878

NSP 1..SUB ASSY DWM2619

2..PARA ASSY DWX3874

2..DSF ASSY DWX3875

2..STBY ASSY DWX3876

Mark No. Description Part No.

8TSP-16

12 3 4

4. BLOCK DIAGRAM

4.1 OVERALL WIRING DIAGRAM

LMT_CONT

SEL_xTHRU/DSF

V+3R3E

GNDD

GND_LED

V+5R1_BL

LPF_RES_BOOST_CV

V+5A_DSF

GNDD_REF

V+3R3D_REF

AD_HPFCV

CDC_INT

V+3R3D

M1_SEG34

M1_SEG32

M1_SEG33

M1_SEG36

M1_SEG35

M1_SEG37

M1_G2_SEQ1

M1_G0_SEQ1

M1_SEG30

M1_SEG31

Enc_P3_1

GND_LED

M2_GRID1

M2_GRID0

M1_G0_BAR

M1_G1_BAR

M1_S28_BAR

GNDD

GND_LED

LED_STBY

KEY_STBY

GNDD

MCK

GNDD

BCK_TDM

GNDD

LRCK_TDM

GNDD

BCK_I2S

GNDD

LRCK_I2S

GNDD

ADAT_INPUT

GNDD

ADAT_DSF_RTN

GNDD

ADAT_DSF_SND

GNDD

ADAT_HP

GNDD

ADAT_OUTPUT

iMX_DAC_SDA

L_MUTE

iMX_DAC_SCL

GNDD

iMX_IDAC_SCLK

GNDD

iMX_IDAC_MOSI

GNDD

iMX_IDAC_xCS

A_FDET

ADDA_xRST

V+3R3D_CLK

GNDD

V+12A

GNDD

V-12A

GNDD

GNDD_REF

AD_MVR

LPF_FREQ_CV

V+OPA_DSF

GNDA

V-OPA_DSF

M1_GRID0_MODE

M1_GRID1_MODE

M1_GRID2_MODE

M1_SEG1_MODE

M1_SEG6

GND_LED_2

CDC_xCS

GNDD

CDC_SCK

GNDD

CDC_SDI

GNDD

CDC_SDO

GNDD

GND_LED

M1_G1_SEQ1

M1_SEG29

GNDD

M2_GRID0

M2_GRID1

M2_GRID2

M2_GRID3

M2_EG4

M2_SEG5

GNDD

M2_GRID0

M2_GRID1

M2_GRID2

M2_GRID3

M2_SEG6

M2_SEG7

GNDD

M1_SEG38

M1_SEG40

M1_SEG39

M1_SEQ43

M1_SEQ41

M1_SEQ42

M1_SEQ45

M1_SEQ44

M1_SEQ46

GND_LED

M1_G1_SEQ2

M1_G2_SEQ2

M1_G0_SEQ2

Enc_P2_0

Enc_P4_0

GNDD

M2_S8

M1_S27

M1_G1

M1_G0

M1_S28

M2_S3

M2_S26

M2_S2

M1_S25

V+5R1_LED

GND_LED

V+3R3D

GNDD

M2_G1

M2_G2

M2_G3

M2_S0

GNDD

ENC_S0

ENC_S1

GNDD

V_TPX

AD_TPX

AD_TPY

V_TPY

GNDD

KEY_STBY

LED_USBCN

GNDD

iMX_CDC_xINT

iMX_CDC_xCS

GNDD

PWRSW_xON

iMX_M2_xINT

iMX_M2_xCS

GNDD

iMX_M_SCLK

GNDD

iMX_M_MOSI

GNDD

iMX_CDC_SCLK

GNDD

iMX_CDC_MOSI

GNDD

iMX_CDC_MISO

GNDD

iMX_CDC_Pcon

M1_UD_RST

xAC_OFF

iMX_M1_xINT

IMX_RST

V+12A_CONT

V+12SW_CONT

iMX_M_MISO

GNDD

iMX_M1_xCS

FAULT_DET

xMUTE

V+3R3D_REF

LED_ACTIVE

KEY_ACTIVE

LED_CLIP

V+5R1_LED

GNDD_REF

GNDD

AD_DRIVE

M2_GRID2

M2_GRID3

M2_SEG8

M1_S27_BAR

GND_LED

GNDD

LED_STBY

V+5R1D

GND_LED

V+3R3D

LCD_xRST

GNDD

LVDS_N0

LVDS_P0

GNDD

LVDS_N1

LVDS_P1

GNDD

LVDS_N2

LVDS_P2

GNDD

LVDS_CLKN

LVDS_CLKP

GNDD

LCD_PWM

GND_BL

V+5R2D_USBA

GNDD_USBA

V+5R2D_USBA

GNDD_USBA

USBA_DN

GNDD_USBA

USBA_DP

GNDD_USBA

MasL_OUT

GNDD_REF

GNDA

MasR_OUT

GNDA

MasR_IN

AD_MVR

V+3R3D_REF

GNDA

MasL_IN

GNDA

AGND

Cathode

Anode

AVDD

VCC

GND

VGL

VCC

VGH

DCLK

HSD

VSD

MODE

RSTB

STBYB

SHLR

VCC

UPDN

GND

AGND

AVDD

VCOM

DITH

V10

M1_S24

M2_G0

M2_G1

M2_G2

M2_G3

Enc_P6_0

Enc_P6_1

Enc_P5_0

Enc_P5_1

Enc_P1_1

Enc_P1_0

Enc_P4_1

Enc_P2_1

Enc_P3_0

M1_G2

CN4

21R-1.25FJ

VKN1436-A

CN1

VKN1434-A

CN2

CN5000

21P-1.25FJ

CN5001

21P-1.25FJ

VKN1412-A

CN5002

CN5601

VKN1409-A

VKN1434-A

CN7000

VKN1427-A

CN7500

CN7501

VKN1409-A

VKN1436-A

CN8011

VKN1413-A

CN8003

VKN1427-A

CN8012

VKN1414-A

CN8005

CN8002

VKN1409-A

VKN1434-A

CN8006

VKN1425-A

CN8008

VKN1425-A

CN8007

VKN1425-A

CN7800

VKN1425-A

CN9700

VKN1416-A

CN8900

VKN1413-A

CN7700

VKN1261-A

CN9000

VKN1272-A

CN9001

VKN1241-A

CN6900

VKN1239-A

CN6901

CN9200

VKN1235-A

CN3

21R-1.25FJ

VKN1410-A

CN8013

VKN1410-A

CN9400

CN3501

AKM7101-B

CN7601

AKN7067-B

CN6800

AKN7067-B

CN5600

AKM7101-B

CKS4428-A

CN7100

CN7300

CKS6646-A

CN7502

CKS6625-A

AC ADAPTOR

DWR1553-A

/SYXJ ADG1154-B

/UXJCB XDG3052-A

/JXJ DDG1112-A

/AXJ ADG7079-B

AC POWER CORD

JA7600

DKB1118-A

USB CONNECTOR

(A-TYPE)

TFT-LCD Module

TOUCH PANEL

DDD1753-A

P=1.0mm, L=285mm

DDD1754-A

P=1.0mm, L=150mm

DDD1755-A

P=1.0mm, L=50mm

DDD1756-A

P=1.0mm, L=55mm

DDD1757-A

P=1.0mm, L=55mm

DDD1758-A

P=1.0mm, L=105mm

DDD1759-A

P=1.0mm, L=70mm

DDD1760-A

P=1.0mm, L=150mm

DDD1761-A

P=1.0mm, L=55mm

DDD1762-A

P=1.0mm, L=38mm

DDD1763-A

P=1.0mm, L=185mm

DDD1533-A

P=1.0mm, L=55mm

DDD1765-A

P=1.0mm, L=190mm

BtoB CONNECTOR

PHONESOUT1-2

/MASTER OUT3-4

INPUT

JA200

DKN1649-A

S200

ASG1102-A

JA4100

DKN1237-A

USB-B MIDI-IN MIDI-OUT

/THRU

JA3201

DKN1188-A

JA3200

DKN1188-A

JA2600

AKN7115-A

LINK

DC IN

POWER SW

JA6600

DKN1622-A

JA5606

DKN1614-A

JA5607

DKN1614-A

JA5604

DKN1614-A

JA5605

DKN1614-A

JA5602

DKN1614-A

JA5603

DKN1614-A

JA5600

DKN1614-A

JA5601

DKN1614-A

JA5200

DKN1614-A

JA5201

DKN1614-A

BackLight

CWX4352-A

DSX1128-A

OUT5-6 OUT7-8

INPUT

LEVEL

VR5200

DCS1133-A

C C

1/12- 12/12

MAIN ASSY

(DWX3864)

A A

1/8- 8/8

IO ASSY

(DWX3865)

BMVR ASSY

(DWX3866)

Note:

The 1 and 2 ASSYs of SEQ* ASSYs have the same

circuitry, parts, and board shapes.

Only printed information is different, because their

part numbers and wiring numbers are different.

They are handled similarly in their production

management.

Therefore, either 1 or 2 ASSY of the respective ASSYs

is assembled in the respective place.

4. BLOCK DIAGRAM

USBA ASSY

(DWX3868)

LCD ASSY (DWX3867)

PARA ASSY

(DWX3874)

E E

1/4- 4/4

FSTBY ASSY

(DWX3876)

NBAR ASSY

(DWX3872)

GDSF ASSY

(DWX3875)

H H

1/5- 5/5

PADB ASSY

(DWX3869)

MODE ASSY

(DWX3878)

CDC ASSY

(DWX3873)

KSEQ1 ASSY*

(DWX3870) LSEQ2 ASSY*

(DWX3871)

TSP-16

56 7 8

4.2 SIGNAL BLOCK DIAGRAM

MAIN ASSY

LCD ASSY

PADB ASSY

IO ASSY

USBA ASSY

CDC ASSY

VOLUME

INPUT

RY5400

RY6200

10 TSP-16

12 3 4

4.3 POWER BLOCK DIAGRAM

2.8V

IC5004

(NJM79M09DL1A)

V-9HP

IC5005

(UA78M05IKVURG3)

IC2300,2301 (K4B4G1646D-BCMA)

IC3800 (THGBMHG6C1LBAWL)

3.3V

IC7000 (BU90R104)

IC2601 (MX30LF2G18AC-TI)

IC7700 (AD7147ACPZ500RL7)

IC2602 (LAN8720A-CP)

V+2R5VPH

IC5007

(NJM7805DL1A)

IC5006

(UA78M33IKVG3)

V+3R3A

IC5001

(NJM79M09DL1A)

V+3R3VGEN6

IC5203, IC6001

(AK5386VT)

IC6601, IC6602

(NJM4556AD)

IC4100

(S2R72V27)

V+5A

V+2R8VHIGH

V+1R8VGEN4

V+5A_REF

IC5400

(AK4458VN)

IC6000, IC6600

(AK4452VN)

TOUCH PANEL (DSX1128)

IC8008(R5F364AENFA)

RY5400, RY6200(VSR1008)

V-OPA

OPAMP

VDDARM23_IN

VDDHIGH_CAP

VDDHIGH_IN

VDD_SNVS_IN

NVCC_DRAM

VDDARM_IN

VINREFDDR

VIN1

3.0V

V+3VSNVS

1.5V

V+1R5VGEN1

V+1R375CORE

LDO

VREFDDR

V+5SWBST

LCD

(CWX4352)

LCD Backlight

MIDI OUT

LED

LDO

VGEN2

LDO

VSNVS

VIN

SW1CIN

SW2IN

SW4IN

SWBSTIN

DC/DC

SW1C

DC/DC

SW3A

LDO

VGEN3

LDO

VGEN4

LDO

VGEN5

V-12A

IC3500

(NJM2831F33)

V+3R3D_CLK

VIN3

Q502

(RTQ040P02)

V+12A

CLK[22.5792MHz]

IC502

(TPS2557DRB)

IC5002

(NJM78M09DL1A)

V+9A_ADDA

VIN2

IC5003

(NJM78M09DL1A)

V+9HP

IC501

(NJW4155GM1-A)

LDO

VGEN6

IC5000

(NJM78M09DL1A)

V+OPA

IC200

(MM1856A50N)

V+12E

V+5E

Q209

V+12SW

AC Adapter

DWR1553

(DC12V/3A)

AC IN

(AC100-240V)

IC8005

(R5F364AENFA)

POWER SW

IC203

(NJM2872BF33)

V+3R3E

V+5R1D

IC201

(MM3543BH)

USB-A Bus Power

SW3AIN

SW3BIN

USBPWR_OC

IC500

(MM3543BH)

V+5R2D_USB

V+9R6

V+18

IC7101

(BD81A04EFV)

V+5R1D_CONT

USBPWR_EN

DC/DC

SW1B

V+4R2D

DC/DC

SW1A

1.375V

OVP

V+12SW_CONT

V+12A_CONT

IC800 (MMPF0100F0AEP)

SW1BIN

1.5V

IC202

(MM3543BH)

IC7100

(R1290K103A)

SW1AIN

V-6

3.3V

V+2R5VGEN3

1.8V

V+1R5VGEN2

IC2000

(MCIMX6Q5EYM10AD)

NVCC_****

1.375V

V+1R375SOC

3.3V

V+3R3D

V+3R15AUX

V+1R5DDR

LDO

VGEN1

1.5V

VDDSOC_IN

5.0V

3.3V

1.5V

V+0R75MVREF

NVCC_RGMII

NVCC_MIPI

NVCC_LVDS2P5

DC/DC

SW3B

DC/DC

SW4

DC/DC

SWBST

DC/DC

SW2

MAIN ASSY

LCD ASSY

PADB ASSY

IO ASSY

CDC ASSY

LCD ASSY

PADB ASSY

VOLTAGE MONITRING

CIRCUIT

Andere Handbücher für TSP-16

Inhaltsverzeichnis

Andere PIONEER DJ Probennehmer Handbücher

PIONEER DJ

PIONEER DJ DJS-1000 Bedienungsanleitung

Beliebte Probennehmer Handbücher anderer Marken

Lambda

Lambda OMNICOLL Bedienungsanleitung

GSi

GSi IS TD Bedienungsanleitung

Akai

Akai S01 Bedienungsanleitung

Teledyne

Teledyne Everywhereyoulook BLZZRD Betriebsanleitung

Roland

Roland SP-404MKII Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8697 Leitfaden

Akai

Akai MPCX Bedienungsanleitung

KAM

KAM Simple Precision IAS Bedienungsanleitung

YZ Systems

YZ Systems DynaPak DP-2010FU Stücklistenhandbuch

YZ Systems

YZ Systems DynaPak 2010N Series Bedienungsanleitung

YZ Systems

YZ Systems DynaPak DP-2010UX Stücklistenhandbuch

Novation

Novation Circuit Rhythm Bedienungsanleitung

Hach

Hach AS950 AWRS Bedienungsanleitung

GSi

GSi GCE 45 Bedienungsanleitung

M&C

M&C SP2500-H Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 8697 Benutzerhandbuch

Boomerang

Boomerang III Bedienungsanleitung

Campbell

Campbell PVS5120 Series Bedienungsanleitung