Pioneer AVIC-HD3 Bedienungsanleitung

INSTALLATION MANUAL

MANUEL D’INSTALLATION

HDD AV NAVIGATION HEAD UNIT

UNITE CENTRALE AV AVEC NAVIGATION SUR

DISQUE DUR

AVIC-HD3

English NederlandsItalianoFrançaisDeutschEspañol

Important Safety Information

ABOUT THIS MANUAL 3

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN THEM

FOR FUTURE REFERENCE 3

Connecting the System

Precautions before connecting the

system 4

Before installing this product 5

To prevent damage 5

–Notice for the blue lead 5

–Notice for the blue/white lead 6

Parts supplied 6

Connecting the system 8

Connecting the power cord (1) 10

Connecting the power cord (2) 12

When connecting to separately sold power

amp 14

When connecting a rear view camera 16

When connecting the external video

component 17

When connecting the external unit featuring

video source 17

When connecting the rear display 18

–When using a rear display connected to

rear video output 18

Installation

Precautions before installation 19

To guard against electromagnetic

interference 20

Before installing 20

Installing this navigation system 20

–Installation notes 20

–Parts supplied 22

–Before installing this navigation

unit 23

–Installation with the holder and side

bracket 23

–Installation using the screw holes on

the side of the navigation unit 24

Installing the GPS aerial 25

–Installation notes 25

–Parts supplied 25

–When installing the aerial inside the

vehicle (on the rear shelf) 26

–When installing the aerial outside the

vehicle (on the body) 27

Installing the microphone 28

–Parts supplied 28

–Mounting on the sun visor 28

–Installation on the steering column 28

–Adjusting the microphone angle 29

After Installation

After Installing this Navigation System 30

Contents

Engb

ABOUT THIS MANUAL

This manual explains how to install this navi-

gation system in your vehicle. Operation of

this navigation system is explained in the se-

parate operation manual or hardware manual

for the navigation system. Before operating

this navigation system, be sure to read

them.

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING

YOUR NAVIGATION SYSTEM

AND RETAIN THEM FOR

FUTURE REFERENCE

1 Read this manual fully and carefully before in-

stalling your navigation system.

2 Keep this manual handy for future reference.

3 Pay close attention to all warnings in this

manual and follow the instructions carefully.

4 This navigation system may in certain circum-

stances display erroneous information regard-

ing the position of your vehicle, the distance

of objects shown on the screen, and compass

directions. In addition, the system has certain

limitations, including the inability to identify

one-way streets, temporary traffic restrictions

and potentially unsafe driving areas. Please

exercise your own judgement in the light of

actual driving conditions.

5 As with any accessory in your vehicle’s inter-

ior, the navigation system should not divert

your attention from the safe operation of your

vehicle. If you experience difficulty in operat-

ing the system or reading the display, please

make adjustments while safely parked.

6 Please remember to wear your seat belt at all

times while operating your vehicle. If you are

ever in an accident, your injuries can be con-

siderably more severe if your seat belt is not

properly fastened.

7 In certain countries, laws may restrict the pla-

cement and use of navigation systems in your

vehicle. Please comply with all applicable

laws and regulations in the installation and

operation of your navigation system.

WARNING

Do not attempt to install or service your naviga-

tion system by yourself. Installation or servicing

of the navigation system by persons without train-

ing and experience in electronic equipment and

automotive accessories may be dangerous and

could expose you to the risk of electric shock or

other hazards.

Important Safety

Information

Engb 3

English

Section

Precautions before

connecting the system

WARNING

Pioneer does not recommend that you install

your navigation system yourself. We recom-

mend that only authorised Pioneer service

personnel, who have special training and ex-

perience in mobile electronics, set up and in-

stall this product. NEVER SERVICE THIS

PRODUCT YOURSELF. Installing or servi-

cing this product and its connecting cables

may expose you to the risk of electric shock

or other hazards, and can cause damage to

the navigation system that is not covered by

warranty.

CAUTION

!If you decide to perform the installation

yourself, and have special training and ex-

perience in the mobile electronics instal-

lations, please carefully follow all of the

steps in the installation manual.

!Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir-

ing to remain exposed.

!Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger com-

partment into the engine compartment. If

the yellow lead’s insulation tears as a re-

sult of contact with metal parts, short-cir-

cuiting can occur, resulting in

considerable danger.

!It is extremely dangerous to allow the

cables to become wound around the steer-

ing column or gearstick. Be sure to install

this product, its cables, and wiring away

in such a way that they will not obstruct

or hinder driving.

!Make sure that the cables and wires are

routed and secured so they will not inter-

fere with or become caught in any of the

vehicle’s moving parts, especially the

steering wheel, gearstick, handbrake, slid-

ing seat tracks, doors, or any of the vehi-

cle’s controls.

!Do not route wires where they will be ex-

posed to high temperatures. If the insula-

tion heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

!Do not cut the GPS aerial cable to shorten

it or use an extension to make it longer.

Altering the aerial cable could result in a

short circuit or malfunction.

!Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis-

tor or filter, etc.) may fail to work properly.

!Never feed power to other electronic pro-

ducts by cutting the insulation of the

power supply lead of the navigation sys-

tem and tapping into the lead. The current

capacity of the lead will be exceeded,

causing overheating.

!The black lead is earth. Please earth this

lead separately from the earth of high-cur-

rent products such as power amps. Do not

earth more than one product together

with the earth from another product. For

example, you must separately earth any

amp unit away from the earth of this navi-

gation system. Connecting earths to-

gether can cause a fire and/or damage the

products if their earths became

detached.

Connecting the System

Engb

Section

Before installing this product

!This product is for vehicles with a 12-volt

battery and negative earthing. Check the

battery voltage of your vehicle before instal-

lation.

!To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be-

fore beginning installation.

To prevent damage

!When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

!This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

ACC position No ACC position

!When replacing the fuse, be sure to only

use a fuse of the rating prescribed on the

fuse holder.

!To avoid a short-circuit, cover the discon-

nected lead with insulating tape. Insulate

the unused speaker leads without fail.

There is a possibility of a short-circuit if the

leads are not insulated.

!Attach the connectors of the same colour

to the corresponding coloured port, i.e.,

blue connector to the blue port, black to

black, etc.

!Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

!Since a unique BPTL circuit is employed,

do not directly earth the *side of the

speaker lead or connect the *sides of the

speaker leads together. Be sure to connect

the *side of the speaker lead to the *

side of the speaker lead on this navigation

system.

!If the RCA pin jack on this product will not

be used, do not remove the caps attached

to the end of the connector.

!Speakers connected to this navigation unit

must be high-power with minimum rating

of 50 W and impedance of 4 to 8 ohms.

Connecting speakers with output and/or

impedance values other than those noted

here may result in the speakers catching

fire, emitting smoke, or becoming da-

maged.

Notice for the blue lead

!A signal is output through the blue lead to

control the aerial of your vehicle. The tim-

ing varies depending on the setting. (For

more detailed information on changing

[Auto ANT] mode, refer to the operation

manual.)

!When [Auto ANT] mode is set to [Radio],

the vehicle’s aerial can be stowed or turned

off by following the instructions below.

—Change the source from radio (AM or

FM) to another source

—Turn the source off

—Turn off the ignition switch (ACC OFF)

Connecting the System

Engb 5

English

Section

!If [Auto ANT] mode is set to [Power], the

vehicle’s aerial can be stowed or turned off

only when the ignition switch is turned off

(ACC OFF).

!Do not connect this lead to the system con-

trol terminal of external power amps.

!Be sure not to use this lead as the power

supply lead for the auto-aerial or aerial

booster. Such connection could cause ex-

cessive current drain and malfunction.

Notice for the blue/white lead

!When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal (max. 300 mA 12 V DC). The control sig-

nal is output through the blue/white lead,

even if the audio source is switched off.

!Do not connect this lead to the auto-aerial

relay control terminal or the aerial booster

power control terminal.

!Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

Parts supplied

The navigation unit Power cord

Connector Extension lead

(for reverse signal)

Extension lead

(for speed signal)

GPS aerial

RCA connector 1

(CONNECTOR 1)

RCA connector 2

(CONNECTOR 2)

<See Page 8, 12, 16,

18>

Microphone

Connecting the System

Engb

Section

Connecting the System

Engb 7

English

Section

Connecting the system

Black

Bluetooth unit (ND-BT1)

(sold separately)

Aerial

jack

Vehicle

aerial

The navigation unit

RCA connector 2

20 cm

Red

Light grey

GPS aerial

Blue

Not used.

Microphone input

Blue

EXTENSION port

Not used.

Jack for Wired Remote

Control Adapters

(WIRED REMOTE INPUT)

Please see the instruction manual

for the Wired Remote Control

Adapters (sold separately).

AV-BUS cable

(supplied with TV tuner)

IP-BUS cable

(supplied with TV tuner)

Multi-CD player

(sold separately)

Hide-away TV tuner

(e.g. GEX-P5700TVP)

(sold separately)

Connecting the System

Engb

Section

Dock connector port

iPod®with

Dock connector

Interface adapter for iPod

(e.g. CD-IB100II)

(sold separately)

Black

Microphone

(supplied)

Blue

4 m

WARNING

· To avoid the risk of accident and the potential violation of applicable laws, this

product should never be used while the vehicle is being driven except for

navigation purposes. And, also Rear Displays should not be in a location where it is

a visible distraction to the driver.

· In some countries, the viewing of images on a display inside a vehicle even by

persons other than the driver may be illegal. Where such regulations apply they

must be obeyed and this product´s video source or TV features should not be used.

IP-BUS cable

(supplied with iPod adapter)

Connecting the System

Engb 9

English

Section

Connecting the power cord (1)

ISO connector

Speaker leads

White: Front left 

White/black:Front left 

Grey: Front right 

Grey/black: Front right 

Green: Rear left or Subwoofer (*9)

Green/black:Rear left or Subwoofer (*9)

Violet: Rear right or Subwoofer (*9)

Violet/black:Rear right or Subwoofer (*9)

Depending on the kind of vehicle, the function

of *3 and *5 may be different. In this case, be

sure to connect *2 to *5 and *4 to *3.

Connect leads of the

same colour to each

other.

Cap (*1)

When not using this terminal,

do not remove the cap.

Yellow (*3)

Back-up

(or accessory)

Red (*5)

Accessory

(or back-up)

Yellow (*2)

To terminal always supplied

with power regardless of

ignition switch position.

Red (*4)

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (earth)

To vehicle (metal) body.

In some vehicles, the ISO connector may be divided into two.

In this case, be sure to connect to both connectors.

Yellow/black

If the vehicle can send a mute signal to this terminal, the

mute function can be activated on this navigation system

when the terminal is connected to *8.

Note

Note Notes

· When a subwoofer (*9) is connected to this

navigation system instead of a rear speaker, change

the rear output setting in the Initial Setting. (Refer to

the operation manual.) The subwoofer output of this

navigation system is monaural.

· When using a subwoofer of 70 W (2 Ω), be sure to

connect with violet and violet/black leads of this

navigation unit. Do not connect anything with green

and green/black leads.

Fuse holder

Fuse (10 A)

Connecting the System

Engb

Section

Andere Handbücher für AVIC-HD3

Inhaltsverzeichnis

Sprachen:

Andere Pioneer Auto-Navigationssystem Handbücher

Pioneer

Pioneer AVIC-505 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z730DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-Z140BH Bedienungsanleitung

Pioneer

Pioneer AVIC-Z930DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-Z810DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-505 Bedienungsanleitung

Pioneer

Pioneer AVIC-880DVD Bedienungsanleitung

Pioneer

Pioneer AVIC Z3 - Navigation System With DVD player Bedienungsanleitung

Pioneer

Pioneer AVIC-U250 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z120BT Bedienungsanleitung

Pioneer

Pioneer AVIC-F220 Bedienungsanleitung

Pioneer

Pioneer AVIC-F160 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z110BT Bedienungsanleitung

Pioneer

Pioneer AVIC-Z150BH Gebrauchs- und Pflegehandbuch

Pioneer

Pioneer AVIC-HD3 Bedienungsanleitung

Pioneer

Pioneer AVIC-F60DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-S1 Bedienungsanleitung

Pioneer

Pioneer AVIC-F77DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-F9310BT Bedienungsanleitung

Pioneer

Pioneer AVIC-EVO1-PL2-VAL Bedienungsanleitung

Pioneer

Pioneer AVIC-Z2 - Navigation System With DVD player Bedienungsanleitung

Pioneer

Pioneer AVIC-F8430BT Bedienungsanleitung

Pioneer

Pioneer AVIC-F160-2 Bedienungsanleitung

Pioneer

Pioneer AVIC-W6600NEX Bedienungsanleitung

Beliebte Auto-Navigationssystem Handbücher anderer Marken

Clarion

Clarion Navigation In-Car Entertainment Bedienungsanleitung

Rosen

Rosen DP-1001 Bedienungsanleitung

Alpine

Alpine INE-W970HD Bedienungsanleitung

Skoda

Skoda AMUNDSEN+ Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot DX-N Bedienungsanleitung

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung

Kenwood

Kenwood DNN991HD Bedienungsanleitung

AvMap

AvMap Geosat 2C Bedienungsanleitung

Eonon

Eonon GE01B Bedienungsanleitung

Nextar

Nextar M3-MX - Automotive GPS Receiver Bedienungsanleitung

Furrion

Furrion NV2200 Bedienungsanleitung

Mio

Mio MOOV 200-Series Bedienungsanleitung

Prestigio

Prestigio GeoVision 5150 Bedienungsanleitung

Hummer

Hummer 2006 H3 Bedienungsanleitung

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch

Garmin

Garmin StreetPilot c510 Bedienungsanleitung

Garmin

Garmin nüvi 2200 Bedienungsanleitung

Garmin

Garmin 2610/2650 Bedienungsanleitung