Pioneer Super Tuner IIID AVIC-X710BT Bedienungsanleitung

INSTALLATION MANUAL

MANUEL D’INSTALLATION

FLASH MEMORY MULTIMEDIA AV NAVIGATION

RECEIVER

RECEPTEUR AV MULTIMEDIA A MEMOIRE FLASH

AVEC SYSTEME DE NAVIGATION

AVIC-X910BT

AVIC-X710BT

English Français

IMPORTANT INFORMATION

ABOUT YOUR NEW NAVIGATION SYSTEM

AND THIS MANUAL 3

IMPORTANT SAFEGUARDS

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN THEM

FOR FUTURE REFERENCE 4

Connecting the System

Precautions before connecting the

system 5

Before installing this product 6

To prevent damage 6

–Notice for the blue lead 6

–Notice for the blue/white lead 7

Parts supplied 7

Connecting the system 8

Connecting the power cord (1) 10

Connecting the power cord (2) 12

When connecting to separately sold power

amp 14

When connecting a rear view camera 16

When connecting the rear display 17

–When using a rear display connected to

rear video output 17

When connecting the external video

component 17

–Using “AV1 Input”(AV1) 17

–Using “AV2 Input”(AV2) 18

When connecting the external unit featuring

video source 19

Installation

Precautions before installation 20

To guard against electromagnetic

interference 20

Before installing 20

Installing this navigation system 21

–Installation notes 21

–Parts supplied 22

–Installation using the screw holes on

the side of the navigation unit 22

Installing the GPS antenna 23

–Installation notes 23

–Parts supplied 23

–When installing the aerial inside the

vehicle (on the dashboard or rear

shelf) 24

Installing the microphone 25

–Parts supplied 25

–Mounting on the sun visor 25

–Installation on the steering column 26

–Adjusting the microphone angle 27

After Installation

After Installing this navigation system 28

Contents

ABOUT YOUR NEW

NAVIGATION SYSTEM AND

THIS MANUAL

!The navigation features of this product

(and rear view camera option if purchased)

are intended solely to aid you in the opera-

tion of your vehicle. It is not a substitute for

your attentiveness, judgment and care

when driving.

!Never use this navigation system to route

to hospitals, police stations, or similar facil-

ities in an emergency. Please call the ap-

propriate emergency number.

!Do not operate this navigation system (or

the rear view camera option if purchased) if

doing so in any way will divert your atten-

tion from the safe operation of your vehicle.

Traffic restrictions and advisories currently

in force should always take precedence

over guidance given by this product. Al-

ways obey current traffic restrictions, even

if this product provides contrary advice.

!This manual explains how to install this na-

vigation system in your vehicle. Operation

of this navigation system is explained in

the separate manuals for the navigation

system.

!Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s operat-

ing systems of safety features, including

airbags, hazard lamp buttons or (iii) impair

the driver’s ability to safely operate the vehi-

cle. In some cases, it may not be possible

to install this product because of the vehi-

cle type or the shape of the vehicle inter-

ior.

IMPORTANT INFORMATION

En 3

English

Section

WARNING

Pioneer does not recommend that you install

your navigation system yourself. We recom-

mend that only authorized Pioneer service

personnel, who have special training and ex-

perience in mobile electronics, set up and in-

stall this product. NEVER SERVICE THIS

PRODUCT YOURSELF. Installing or servi-

cing this product and its connecting cables

may expose you to the risk of electric shock

or other hazards, and can cause damage to

the navigation system that is not covered by

warranty.

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING

YOUR NAVIGATION SYSTEM

AND RETAIN THEM FOR

FUTURE REFERENCE

1 Read this manual fully and carefully before in-

stalling your navigation system.

2 Keep this manual handy for future reference.

3 Pay close attention to all warnings in this

manual and follow the instructions carefully.

4 This navigation system may in certain circum-

stances display erroneous information regard-

ing the position of your vehicle, the distance

of objects shown on the screen, and compass

directions. In addition, the system has certain

limitations, including the inability to identify

one-way streets, temporary traffic restrictions

and potentially unsafe driving areas. Please

exercise your own judgment in the light of ac-

tual driving conditions.

5 As with any accessory in your vehicle’s inter-

ior, the navigation system should not divert

your attention from the safe operation of your

vehicle. If you experience difficulty in operat-

ing the system or reading the display, please

make adjustments while safely parked.

6 Please remember to wear your seat belt at all

times while operating your vehicle. If you are

ever in an accident, your injuries can be con-

siderably more severe if your seat belt is not

properly buckled.

7 Certain government laws may restrict the pla-

cement and use of navigation systems in your

vehicle. Please comply with all applicable

laws and regulations in the installation and

operation of your navigation system.

IMPORTANT SAFEGUARDS

Section

Precautions before

connecting the system

CAUTION

!If you decide to perform the installation

yourself, and have special training and ex-

perience in the mobile electronics instal-

lations, please carefully follow all of the

steps in the installation manual.

!Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir-

ing to remain exposed.

!Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger com-

partment into the engine compartment. If

the yellow lead’s insulation tears as a re-

sult of contact with metal parts, short-cir-

cuiting can occur, resulting in

considerable danger.

!It is extremely dangerous to allow the

cables to become wound around the steer-

ing column or shift lever. Be sure to install

this product, its cables, and wiring away

in such a way that they will not obstruct

or hinder driving.

!Make sure that the cables and wires are

routed and secured so they will not inter-

fere with or become caught in any of the

vehicle’s moving parts, especially the

steering wheel, shift lever, parking brake,

sliding seat tracks, doors, or any of the ve-

hicle’s controls.

!Do not route wires where they will be ex-

posed to high temperatures. If the insula-

tion heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

!Do not cut the GPS antenna cable to

shorten it or use an extension to make it

longer. Altering the antenna cable could

result in a short circuit or malfunction.

!Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis-

tor or filter, etc.) may fail to work properly.

!Never feed power to other electronic pro-

ducts by cutting the insulation of the

power supply lead of the navigation sys-

tem and tapping into the lead. The current

capacity of the lead will be exceeded,

causing overheating.

!The black lead is ground. Please ground

this lead separately from the ground of

high-current products such as power

amps. Do not ground more than one pro-

duct together with the ground from an-

other product. For example, you must

separately ground any amp unit away

from the ground of this navigation sys-

tem. Connecting grounds together can

cause a fire and/or damage the products if

their grounds became detached.

Connecting the System

En 5

English

Section

Before installing this product

!This product is for vehicles with a 12-volt

battery and negative grounding. Check the

battery voltage of your vehicle before instal-

lation.

!To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be-

fore beginning installation.

To prevent damage

WARNING

!When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

!When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

!This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

ACC position No ACC position

!To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

!Attach the connectors of the same color to

the corresponding colored port, i.e., blue

connector to the blue port, black to black,

etc.

!Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

!Since a unique BPTL circuit is employed,

do not directly ground the *side of the

speaker lead or connect the *sides of the

speaker leads together. Be sure to connect

the *side of the speaker lead to the *

side of the speaker lead on this navigation

system.

!If the RCA pin jack on this product will not

be used, do not remove the caps attached

to the end of the connector.

!Never connect speakers with an output rat-

ing of less than 50 W channel or impe-

dance outside of the 4 ohms to 8 ohms

specifications to your navigation system.

Connecting speakers with output and/or

impedance values other than those noted

here may result in the speakers catching

fire, emitting smoke, or becoming da-

maged.

Notice for the blue lead

!A signal is output through the blue lead to

control the antenna of your vehicle. The

timing varies depending on the setting. (For

more detailed information on changing

[Ant CTRL] mode, refer to “Operation Man-

ual”.)

!When [Ant CTRL] mode is set to [Radio],

the vehicle’s antenna can be stowed or

turned off by following the instructions

below.

—Change the source from radio (AM or

FM) to another source.

—Turn the source off

—Turn off the ignition switch (ACC OFF)

!If [Ant CTRL] mode is set to [Power], the

vehicle’s antenna can be stowed or turned

off only when the ignition switch is turned

off (ACC OFF).

Connecting the System

Section

!Do not connect this lead to the system con-

trol terminal of external power amps.

!Be sure not to use this lead as the power

supply lead for the auto-antenna or anten-

na booster. Such connection could cause

excessive current drain and malfunction.

Notice for the blue/white lead

!When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal (max. 300 mA 12 V DC). The control sig-

nal is output through the blue/white lead,

even if the audio source is switched off.

!Do not connect this lead to the auto-anten-

na relay control terminal or the antenna

booster power control terminal.

!Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

Parts supplied

Parts marked (*) are not supplied with AVIC-

X710BT.

The navigation unit Power cord

Connector* Extension lead

(for reverse signal)

Extension lead*

(for speed signal)

GPS antenna

RCA connector Microphone

Connecting the System

En 7

English

Section

Connecting the system

RCA connector

Yellow

(VIDEO INPUT)

20 cm (7-7/8 in.)

Red, white

(AUDIO INPUT)

Antenna

jack

5 m (16 ft. 5 in.)

WIRED REMOTE INPUT

Please see the Instruction

Manual for the Wired Remote

Control Adapters (sold separately).

The navigation unit

4 m (13 ft. 1 in.)

Green

2 m (6 ft. 7 in.)

Vehicle antenna

USB connector

Connect either the interface cable for iPod

or an appropriate USB storage device. *1

— When connecting your iPod, both connections are necessary.

— It is necessary to set [AV1 Input] in [AV Settings] to [iPod]

when connecting the iPod. (For details, refer to “Operation

Manual”.)

Blue

Black

XM tuner (e.g. GEX-P920XM)

(sold separately)

Blue

IP-BUS cable

(supplied with hide-away XM tuner)

Connecting the System

Section

Dock

connector

port

GPS antenna

Microphone

USB Interface Cable for iPod

(CD-IU230V) (sold separately)

Blue Black

HD-Radio tuner (e.g. GEX-P20HD)

(sold separately)

To IP-BUS output

Black

WARNING

· To avoid the risk of accident and the potential

violation of applicable laws, this product should

never be used while the vehicle is being driven

except for navigation purposes. Also Rear

Displays should not be in a location where it is

a visible distraction to the driver.

· In some countries or states, the viewing of

images on a display inside a vehicle even by

persons other than the driver may be illegal.

Where such regulations apply they must be

obeyed and this product´s video source should

not be used.

IP-BUS cable

(supplied with SIRIUS satellite radio tuner)

IP-BUS cable

(supplied with HD-Radio tuner)

The XM tuner, HD-Radio tuner and SIRIUS satellite

radio tuner will not receive their service when you

drive outside of their coverage area.

Note

SIRIUS BUS INTERFACE

(e.g. CD-SB10)

(sold separately)

“SiriusConnect universal tuner”

or “SIRIUS Dock and Play radio

with SiriusConnect vehicle kit”

(sold separately)

SiriusConnect Cable

(sold separately)

For details concerning

operations and compatibility,

refer to the operation manual.

iPod with

Dock Connector*2

Connecting the System

En 9

English

Section

Connecting the power cord (1)

White

White/Black

Gray

Gray/Black

Green

Green/Black

Violet

Violet/Black

Front speakerFront speaker

Left Right

















Rear speaker or

Subwoofer (4

Ω

)

Rear speaker or

Subwoofer (4

Ω

)





Violet

Violet/Black

Green

Green/Black

Not used. Subwoofer (4

Ω

)



When using a subwoofer of 70 W (2

Ω

), be sure to connect with violet and violet/black leads of this

navigation system. Do not connect anything with green and green/black leads.

Yellow

To terminal always supplied with power

regardless of ignition switch position.

Red

To electric terminal controlled by ignition

switch (12 V DC) ON/OFF.

Orange/White

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

With a 2 speaker system, do not connect anything to

the speaker leads that are not connected to speakers.

When a subwoofer is connected to this navigation

system instead of a rear speaker, change the rear

output setting in the Initial Setting. (Refer to

“

Operation Manual

”

.) The subwoofer output of this

navigation system is monaural.

Note

Connecting the System

Section

Andere Handbücher für Super Tuner IIID AVIC-X710BT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Pioneer Auto-Videosystem Handbücher

Pioneer

Pioneer AVH-P5900D Bedienungsanleitung

Pioneer

Pioneer MVH-AV290BT Bedienungsanleitung

Pioneer

Pioneer AVD-W6200 Bedienungsanleitung

Pioneer

Pioneer AVD-505 Bedienungsanleitung

Pioneer

Pioneer AVIC-Z1000D33-CHU Bedienungsanleitung

Pioneer

Pioneer AVHP5700DVD - In-Dash 6.5 Monitor DVD Player Bedienungsanleitung

Pioneer

Pioneer Super Tuner IIID DVH-P5000MP Bedienungsanleitung

Pioneer

Pioneer DEH-P55BT/XN/EW5 Bedienungsanleitung

Pioneer

Pioneer AVH-P2300DVD Bedienungsanleitung

Pioneer

Pioneer Super Tuner IIID AVH-P5000DVD Bedienungsanleitung

Pioneer

Pioneer AVH-P7600D Bedienungsanleitung

Pioneer

Pioneer AVIC-D3 - Navigation System With DVD Player Bedienungsanleitung

Pioneer

Pioneer AVH-P7480DVD Bedienungsanleitung

Pioneer

Pioneer Super Tuner IIID AVIC-F7010BT Bedienungsanleitung

Pioneer

Pioneer AVD-W7900 Bedienungsanleitung

Pioneer

Pioneer AVH-P7600DVD Bedienungsanleitung

Pioneer

Pioneer AVIC-F940BT Bedienungsanleitung

Pioneer

Pioneer AVH-P6800DVD - DVD Changer With LCD Monitor Bedienungsanleitung

Pioneer

Pioneer DMH-WT8600NEX Bedienungsanleitung

Pioneer

Pioneer AVIC-X920BT Bedienungsanleitung

Pioneer

Pioneer AVH-P7550DVD Bedienungsanleitung

Pioneer

Pioneer AVH-X490DAB Bedienungsanleitung

Pioneer

Pioneer AVIC-X930BT Gebrauchs- und Pflegehandbuch

Pioneer

Pioneer CNDV-100MT Bedienungsanleitung

Beliebte Auto-Videosystem Handbücher anderer Marken

Stinger

Stinger HEIGH10 RB10RAM13B Bedienungsanleitung

Eonon

Eonon E1057 Bedienungsanleitung

Milion

Milion D2223 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-8153 Bedienungsanleitung

Voxx Electronics

Voxx Electronics HR8MA1 Bedienungsanleitung

Axxera

Axxera AV604Bi Bedienungsanleitung

Clarion

Clarion NX706E Bedienungsanleitung

Pyle view

Pyle view PLDN74BTi Bedienungsanleitung

Clarion

Clarion NX602 Bedienungsanleitung

RCA

RCA DRC6296 - Twin 9" Mobile DVD System Benutzerhandbuch

Kia

Kia MTXM100YPPE Bedienungsanleitung

Lanzar

Lanzar SVDVD5 Bedienungsanleitung

Eonon

Eonon E1060 Bedienungsanleitung

Macrom

Macrom M-AN900 Bedienungsanleitung

Hyundai

Hyundai BAPE-L3000N Bedienungsanleitung

r.LiNK

r.LiNK RL2-UCON8-SM Bedienungsanleitung

Blaupunkt

Blaupunkt DVP 01C Bedienungsanleitung

DP Audio Video

DP Audio Video dbd807nav Bedienungsanleitung