Pioneer DVR-X162Q Bedienungsanleitung

DVR-X162Q

Operating Instructions

Mode d’emploi

DVD / CD WRITER

LECTEUR DE DVD / CD

Thank you for buying this Pioneer product. Before using the drive, read all warnings,

cautions, notices and other important safety information contained in these Operating

Instructions. Please read the entire manual before using this drive as it contains important

information, such as regulatory data, software license agreement(s), product registration

details, service instructions and guidelines.

is a trademark of DVD Format/Logo Licensing Corporation.

SAFETY INSTRUCTIONS

To ensure your personal safety and to maximize the full operating potential of your unit, read and follow

these safety instructions.

Read & Retain Instructions – Read all operating and user information provided with this

drive.

Cleaning – Use a damp cloth to clean the exterior housing. Avoid using any fluids

including liquid, aerosol or alcohol-based cleaning products.

Water or Moisture – Avoid operating or locating this drive near water or other sources of

fluid.

Accessories – Do not place this product on an unstable cart, stand, or table. The product

may fall and be seriously damaged.

Ventilation – Slots and openings in the chassis are for cooling and proper operation of

the unit. Do NOT block or cover the openings. Do NOT place this unit on a bed, rug, etc.

as this can block the openings. This unit should not be placed in a built-in installation

unless properly ventilated.

Environment – Avoid installing this drive in a location with exposure to large quantities of

dust, high temperatures, high humidity, or subject to excessive vibrations or shocks.

Power Sources – Operate this drive only from the recommended power sources. If you

are unsure of the power source, consult an authorized Pioneer representative.

Power-Cord Protection – When unplugging the unit, pull on the plug – not on the cord.

Do not handle the cord or plug with wet hands; doing so could cause an electric short or

shock. Do not allow anything to pinch or rest on the power cord and do not place in a

walkway.

Power – Turn OFF the system before installing this or any other hardware device.

Overloading – Avoid connecting too many devices to a single wall socket or power

source as this can cause fires or short circuits.

Object & Liquid Entry – Never push inappropriate objects in to the device. Avoid spilling

any liquids in to or on the outside of the drive.

Condensation – Moisture can form in the operating section of the product if the drive is

taken from cool surroundings to a room with a warmer temperature. Let the drive stand

for one to two hours in the new location before turning it ON.

Servicing – Opening or removing the cover exposes you to possible electrical shock or

other danger. Contact a Pioneer authorized service representative for repairing this drive

(refer to the enclosed Service & Support Card).

Damage Requiring Service – Unplug the unit and refer servicing to qualified service

personnel in the following situations:

When the power cord, plug, or chassis is damaged

If liquid has been spilled, or objects have fallen into the video product

If the product has been exposed to rain or water

If the product does not operate normally when the operating instructions are

followed. Adjust only those controls that are covered by the operating instructions.

Improper adjustment of other controls may result in damage and can require

extensive work by a qualified technician to restore the unit to its normal operation.

When the product exhibits a distinct change in performance – this indicates a need

for service

About DualDisc Playback – DualDisc is a new two-sided disc with one side

containing DVD video / audio / etc. content and the opposite side containing non-DVD

content such as digital audio material. The non-DVD audio side is not compliant with

the CD Audio Specification; therefore, may not play. The DVD side of DualDisc media

plays in this unit. For more details about the DualDisc specification, please refer to the

disc manufacturer or your retailer.

Note: Some discs may not be playable due to different recording formats or the physical

condition of the disc at the time of recording or playback.

•Avoid touching or scratching the signal surface

(shiny side) of the disc.

•Hold the disc by the edges or by the center hold

and one edge.

•Do not affix paper or labels to the disc.

•Discard warped or cracked discs as they may

cause damage to the drive.

•Avoid specially shaped discs such as hearts or

polygons.

•Remove dust or lint from the disc with a soft

cloth by wiping from the inside to the outside

edge rather than in a circular motion.

•Do not use record-cleaning or anti-static agents

as the solutions may cause damage to a disc.

Always be sure to store your discs in proper disc

storage cases when not in use, and always be

sure to check for dirt or dust on discs (especially

on the recording side) before use.

FEATURES

Interface: USB 2.0

Write Speed (▲ZCLV, ★CAV)

DVD-Download disc* 8X PCAV (6X CLV)

DVD-R 1X, 2X, 4X, 6X, 8X★, 12X★, 16X★, 18X★, 20X★

DVD-R DL 2X, 4X, 6X, 8X▲,10X▲, 12X▲,

DVD-RW 1X , 2X ,4X , 6X

DVD+R 2.4X, 4X, 6X, 8X★, 12X★, 16X★, 18X★, 20X★

DVD+R DL 2.4X, 4X, 6X, 8X▲, 10X▲, 12X▲

DVD+RW 2.4X, 3.3X, 4X, 6X, 8X▲

DVD-RAM 2X, 3X, 5X, 6X, 8X★, 12X★

CD-R 4X, 10X, 16X, 24X, 32X★, 40X★

CD-RW 4X, 10X, 16X, 20X▲, 24X▲, 32X▲

*Note : DVD Download Disc for CSS Managed Recording (Qflix supported software application will be required.)

Maximum Read Speed

DVD-Download disc 12X CAV

DVD-ROM (single) 16X DVD-ROM (dual) 12X

DVD-R, DVD+R 16X DVD-R DL,

DVD+R DL

12X

DVD-RW, DVD+RW 13X DVD-RAM 12X

CD-ROM, CD-R 40X CD-RW 32X

Buffer Memory Size 2 MBytes (Read/Write)

Horizontal / Vertical orientation available

Low vibration Mechanism by DRA System

DVD Download using recordable CSS technology

Disc Format (Read/Write)

DVD-Download disc

DVD single layer/dual layer / 120 mm / 80 mm (Usable only when unit is mounted horizontally) disc

DVD-R (In case of write, 650 nm disc for General only.)

DVD-R (4X, 8X, 16X Write speed)

DVD-R DL

DVD-RW (1X, 2X, 4X, 6X Write speed)

DVD+R (2.4X, 4X, 8X, 16X Write speed)

DVD+R DL

DVD+RW (2.4X, 4X, 8X Write Speed)

DVD-RAM (Ver 2.0, 2.1, 2.2) (Non-Cartridge)

CD-ROM Mode 1

CD-ROM XA Mode2 (form 1, form 2)

Photo CD (single and multiple sessions)

CD-DA

CD-Extra (CD PLUS)

Video-CD

CD Text

CD-R

CD-RW, HS CD-RW, US CD-RW, US+CD-RW

Notes:

・

A specific application program is necessary to write the formats listed above.

・

Supported media required for specific DVD and CD writing speeds.

・

When writing to DVD at 12X, 16X, and 20X use Pioneer-tested media. For media brand information, refer to the

Pioneer website: http://www.pioneerelectronics.com

・

Average writing speed may decrease when multiple discs are written during the same session.

・

20X write speed with DVD±R is possible when USB high-speed driver is used (this driver allows higher data

transmission rates than otherwise possible with USB connections). Note that the USB driver is specific to this

device, and will not produce the same results when used with other devices on the same USB port. Likewise,

high-speed drivers supplied with other devices will not be effective for increasing the transmission speed of this

unit.

INTERFACE

FRONT VIEW

① Forced Ejection Hole

If the tray fails to eject when the Eject button is pressed, insert a stiff rod into the hole

and push to eject the tray.

During normal operation, the eject button should be used to unload the tray. Turn the

power to the drive OFF then wait approximately one minute until the disc stops spinning

before trying to eject the tray redundant prepositional phrase.

② BUSY Indicator

Operation status is indicated as follows:

During reading Lights

During writing Lights

③ Eject Button

Press the button to unload / load the disc.

④ Disc Tray

Press the Eject button to open the loading tray then place a CD or DVD disc onto the

tray with the label facing up. Press the Eject button again or gently push the tray to

close and load.

Do not attempt to forcibly pull out the disc tray – use the Forced Ejection Hole ①.

ABOUT REGION CODES

The region code can only be changed five (5) times, including the initial setting. Please be

aware that the fifth change becomes PERMANENT. Therefore, avoid changing the region

code unless absolutely necessary.

Region codes are part of the DVD Standard. However, region codes on DVD discs

are optional. DVD discs with no specified region code can be played on all

compliant players.

INTERFACE

REAR VIEW

POWER

DC IN

⑤ USB 2.0

4-pin USB 2.0 I/O Connector

⑥ Power on/off switch

⑦ DC In

AC Adapter Connector

Pin Name

1 Ground

2 Ground

3 +12 V

4 +5 V

5 +5 V

Using vertical drive stand

The supplied vertical drive stand can be used if desired to mount the unit vertically as

shown in the accompanying illustration. When using the vertical drive stand, either the right

or left side of the drive unit can be oriented downward in the stand.

Vertical drive stand

CONNECTIONS

Connect the unit to the supplied AC adapter and connect the USB.

AC Adapter Connection

Connect the AC adapter plug for the DC IN connector on the unit’s rear panel.

Use the supplied power cord to connect the AC adapter to a wall outlet.

POWER

DC IN

connect to wall outlet AC Adapter (supplied)

USB Cable Connection

This is a hot-plug unit.

1) Confirm that your computer (PC) has an available USB port.

2) With your Windows® operating system running, use the supplied USB

cable to connect the external drive to the PC.

Note: This unit can operate with USB 1.1 but will not provide optimum

performance.

Warning: Do not disconnect the unit during data transfers.

USB cable (supplied) Computer (PC)

POWER

DC IN

OPERATIONS

The unit writes to DVD-R/-RW media when the supplied software application is installed on

your PC. Writing fails if the PC or operating system does not support the software.

Begin Writing to DVD-R/-RW:

1) Turn on the unit.

2) Turn on the PC.

3) Press the Eject button to open the tray.

4) Place the disc in the tray with the label facing up.

5) Press the Eject button again to close the tray.

6) Start the disc-burning application.

End the Writing Session:

1) Quit the disc burning application.

2) Press the Eject button to open the tray.

3) Remove the disc.

4) Press the Eject button again to close the tray.

5) Shut down the PC.

6) Turn OFF the unit.

For software (including USB high-speed driver) installation directions, please refer to the

manual available on the software disc included with your drive. For assistance with writing

or playing back discs, see the HELP function within the software application.

Manual Disc Ejection

Use the manual eject hole to remove discs if the tray fails to open and all other methods

have been exhausted.

1) Shut down the PC.

2) Wait for the disc to stop spinning.

3) Insert a straightened paper clip or small wire into the manual eject hole.

4) Press firmly until the tray protrudes by at least a ½ inch (5 mm to 10 mm).

5) Gently pull the tray straight out and remove the disc.

Notes:

To prevent injury and damage to the unit, do NOT force the tray to open while the

disc is spinning.

Do not place objects in front of the tray while in operation.

Andere Handbücher für DVR-X162Q

Inhaltsverzeichnis

Sprachen:

Andere Pioneer DVD-Recorder Handbücher

Pioneer

Pioneer PRV-9000 Bedienungsanleitung

Pioneer

Pioneer DVR-RT501-S Bedienungsanleitung

Pioneer

Pioneer PRV-LX10 Bedienungsanleitung

Pioneer

Pioneer DVR-65H-S Bedienungsanleitung

Pioneer

Pioneer PRV-LX1 Bedienungsanleitung

Pioneer

Pioneer DVR-541H-S Bedienungsanleitung

Pioneer

Pioneer DVR-225 Bedienungsanleitung

Pioneer

Pioneer DVR-310 Bedienungsanleitung

Pioneer

Pioneer DVR-65H-S Einrichtungshandbuch

Pioneer

Pioneer DVR-220 Bedienungsanleitung

Pioneer

Pioneer DVD Recorder Bedienungsanleitung

Pioneer

Pioneer DVR-310 Bedienungsanleitung

Pioneer

Pioneer PRV-LX1 Technisches Handbuch

Pioneer

Pioneer DVR-LX61D Bedienungsanleitung

Pioneer

Pioneer DVR-230-S Bedienungsanleitung

Pioneer

Pioneer DVR-510H Bedienungsanleitung

Pioneer

Pioneer DVR-520H Bedienungsanleitung

Pioneer

Pioneer DVR-5100H-S Bedienungsanleitung

Pioneer

Pioneer DVR-230-AV Bedienungsanleitung

Pioneer

Pioneer DVR-5100H-S Bedienungsanleitung

Pioneer

Pioneer PRV-9000 Handbuch

Pioneer

Pioneer PRV-LX10 Bedienungsanleitung

Pioneer

Pioneer PRV-9000 Bedienungsanleitung

Pioneer

Pioneer PRV-LX1 Technisches Handbuch

Beliebte DVD-Recorder Handbücher anderer Marken

Sony

Sony RDR-VX525 - DVDr/ VCR Combo Bedienungsanleitung

Daewoo

Daewoo DHD-4000D Bedienungsanleitung

Medion

Medion MD 40570 Bedienungsanleitung

Philips

Philips ShowView DVDR3460H Bedienungsanleitung

Sony

Sony RDR-GX355 - Tunerless DVD Recorder Bedienungsanleitung

Sony

Sony DVDirect VRD-MC3 Bedienungsanleitung

Samsung

Samsung DVD-R130/XAA Bedienungsanleitung

FUNAI

FUNAI HD-B2735 Bedienungsanleitung

Panasonic

Panasonic DMR-EH54DEG Bedienungsanleitung

Sanyo

Sanyo DRW-1000 Bedienungsanleitung

Philips

Philips DVDR610/05 Bedienungsanleitung

JVC

JVC DR-M10 Bedienungsanleitung

Samsung

Samsung SV-DVD40 Bedienungsanleitung

Philips

Philips DVDR3355 Bedienungsanleitung

FUNAI

FUNAI FDR-90E Bedienungsanleitung

LG RC298 Bedienungsanleitung

Samsung

Samsung DVD-R130 Bedienungsanleitung

Philips

Philips DD-A110GX Bedienungsanleitung