Pioneer AVIC-F80DAB Bedienungsanleitung

Black plate (1,1)

Installation Manual

NAVIGATION AV SYSTEM

AVIC-F80DAB

AVIC-F980DAB

English

<CRB4794-A>1

Black plate (2,1)

Precautions

Your new product and this manual 3

Important safeguards 3

Connection

Precautions before connecting the

system 5

Before installing this product 5

To prevent damage 6

–Notice for the blue/white lead 6

Parts supplied 7

Connecting the power cord (1) 8

Connecting the power cord (2) 10

Connecting the system 12

Connecting to separately sold power

amp 13

Connecting an iPod / iPhone or an Android

device 14

Connecting an iPhone with Lightning

connector 15

–Connecting via the USB port

(iPhone) 15

–Connecting via the HDMI port

(iPhone) 15

Connecting an iPhone with 30-pin

connector 16

–Connecting via the AUX input

(iPhone) 16

–Connecting via the RGB input

(iPhone) 16

Connecting the Android™device 17

–Connecting via the HDMI port (Android

device) 17

–Connecting via the MHL port (Android

device) 17

Connecting via the USB port (Android

device) 18

Securing the High Speed HDMI®Cable 18

Connecting a rear view camera 19

Connecting the external video

component 20

–Using AV input 20

–Using an AUX input 21

Connecting an HDMI device 22

Connecting the rear display 22

–When using a rear display connected to

rear video output 22

Installation

Precautions before installation 23

To avoid electromagnetic interference 23

Before installing 23

–For AVIC-F80DAB users 24

Installing this product 24

–Installation notes 24

–Parts supplied 25

–Installation using the screw holes on

the side of this product 25

Installing the GPS aerial 26

–Installation notes 26

–When installing the aerial inside the

vehicle (on the dashboard or rear

shelf) 27

Installing the microphone 28

–Parts supplied 28

–Mounting on the sun visor 28

–Installation on the steering column 29

–Adjusting the microphone angle 29

After installation

After installing this product 30

<CRB4794-A>2

Contents

Engb

Black plate (3,1)

Your new product and this

manual

!The navigation features of this product

(and the rear view camera option if pur-

chased) are intended solely to aid you in

the operation of your vehicle. It is not a sub-

stitute for your attentiveness, judgement

and care when driving.

!Never use this product to route to hospi-

tals, police stations, or similar facilities in

an emergency. Please call the appropriate

emergency number.

!Do not operate this product, any applica-

tions, or the rear view camera option (if pur-

chased) if doing so will divert your attention

in any way from the safe operation of your

vehicle. Always observe safe driving rules

and follow all existing traffic regulations. If

you experience difficulty in operating this

product or reading the display, park your

vehicle in a safe location and apply the

handbrake before making the necessary

adjustments.

!This manual explains how to install this

product in your vehicle. Operation of this

product is explained in the separate man-

uals.

!Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s operat-

ing systems of safety features, including

airbags, hazard lamp buttons, or (iii) impair

the driver’s ability to safely operate the vehi-

cle. In some cases, it may not be possible

to install this product because of the vehi-

cle type or the shape of the vehicle interior.

!Model icons shown in this manual indicate

that the description is intended for the

models indicated by the icons.

If the following icon is shown, the descrip-

tion is applied only to the model shown.

e.g.)

F80DAB

!The graphical symbol placed on

the product means direct current.

Important safeguards

WARNING

Pioneer does not recommend that you install

this product yourself. This product is de-

signed for professional installation only. We

recommend that only authorised Pioneer ser-

vice personnel, who have special training

and experience in mobile electronics, set up

and install this product. NEVER SERVICE

THIS PRODUCT YOURSELF. Installing or

servicing this product and its connecting

cables may expose you to the risk of electric

shock or other hazards, and can cause da-

mage to this product that is not covered by

warranty.

!Read this manual fully and carefully before

installing this product.

!Keep this manual handy for future refer-

ence.

!Pay close attention to all warnings in this

manual and follow the instructions care-

fully.

!This product may in certain circumstances

display inaccurate position of your vehicle,

the distance of objects shown on the

screen, and compass directions. In addi-

tion, the system has certain limitations, in-

cluding the inability to identify one-way

streets, temporary traffic restrictions and

potentially unsafe driving areas. Please ex-

ercise your own judgement in the light of

actual driving conditions.

!As with any accessory in your vehicle’s in-

terior, this product should not divert your

attention from the safe operation of your

vehicle as it may result in serious injury or

death. If you experience difficulty in operat-

ing the system or reading the display,

please make adjustments while safely

parked.

!Please remember to wear your seat belt at

all times while operating your vehicle. If

you are in an accident, your injuries can be

considerably more severe if your seat belt

is not properly fastened.

<CRB4794-A>3

Engb 3

Section

Precautions

Black plate (4,1)

!Certain country and government laws may

prohibit or restrict the placement and use

of this product in your vehicle. Please com-

ply with all applicable laws and regulations

regarding the use, installation and opera-

tion of this product.

<CRB4794-A>4

Engb

Section

01 Precautions

Black plate (5,1)

Precautions before

connecting the system

WARNING

Do not take any steps to tamper with or dis-

able the handbrake interlock system which

is in place for your protection. Tampering

with or disabling the handbrake interlock

system could result in serious injury or

death.

CAUTION

!If you decide to perform the installation

yourself, and have special training and ex-

perience in the mobile electronics instal-

lations, please carefully follow all of the

steps in the installation manual.

!Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir-

ing to remain exposed.

!Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger com-

partment into the engine compartment. If

the yellow lead’s insulation tears as a re-

sult of contact with metal parts, short-cir-

cuiting can occur, resulting in

considerable danger.

!It is extremely dangerous to allow cables

to become wound around the steering col-

umn or gearstick. Be sure to install this

product, its cables, and wiring away in

such so that they will not obstruct or hin-

der driving.

!Make sure that the cables and wires will

not interfere with or become caught in

any of the vehicle’s moving parts, espe-

cially the steering wheel, gearstick, hand-

brake, sliding seat tracks, doors, or any of

the vehicle’s controls.

!Do not route wires where they will be ex-

posed to high temperatures. If the insula-

tion heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

!Do not cut the GPS aerial cable to shorten

it or use an extension to make it longer.

Altering the aerial cable could result in a

short circuit or malfunction.

!Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis-

tor or filter, etc.) may fail to work properly.

!Never feed power to other electronic pro-

ducts by cutting the insulation of the

power supply lead of this product and tap-

ping into the lead. The current capacity of

the lead will be exceeded, causing over-

heating.

Before installing this product

!Use this product with a 12-volt battery and

negative earthing only. Failure to do so may

result in a fire or malfunction.

!To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be-

fore installation.

<CRB4794-A>5

Engb 5

Section

Connection

Black plate (6,1)

To prevent damage

WARNING

!Use speakers over 50 W (maximum input

power) and between 4 Wto 8 W(impe-

dance value). Do not use 1 Wto 3 Wspeak-

ers for this product.

!The black lead is earth. Please earth this

lead separately from the earth of high-cur-

rent products such as power amps. Do not

earth more than one product together

with the earth from another product. For

example, you must separately earth any

amp unit away from the earth of this pro-

duct. Connecting earths together can

cause a fire and/or damage the products if

their earths became detached.

!When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

!When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

!This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

ACC position No ACC position

!To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

!Attach the connectors of the same colour

to the corresponding coloured port, i.e.,

blue connector to the blue port, black to

black, etc.

!Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

!Since a unique BPTL circuit is employed,

do not directly earth the *side of the

speaker lead or connect the *side of an-

other side of the speaker lead together. Be

sure to connect the *side of the speaker

lead to the *side of the speaker lead on

this product.

Notice for the blue/white lead

Important

When this product is in “Power OFF”mode, the

control signal is also turned off. If “Power OFF”

mode is cancelled, the control signal is output

again and the aerial is extended with the auto aer-

ial function (if the aerial is being used). Be careful

so that the extended aerial does not come into

contact with any obstacles.

!When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal, the auto-aerial relay control terminal,

or the aerial booster power control terminal

(max. 300 mA 12 V DC). The control signal

is output through the blue/white lead, even

if the audio source is switched off.

!Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

!Be sure not to use this lead as the power

supply lead for the auto-aerial or aerial

booster. Such connection could cause ex-

cessive current drain and malfunction.

<CRB4794-A>6

Engb

Section

02 Connection

Black plate (7,1)

Parts supplied

This product Power cord

GPS aerial Microphone

Mini-jack extension

cable

USB cable

Lock tie Vehicle Bus conversion

cable

Metal sheet Clamp (3 pcs.)

Double-sided tape

<CRB4794-A>7

Engb 7

Section

Connection

Black plate (8,1)

Connecting the power cord (1)

Depending on the types of vehicles, the

function of *2 and *4 may be different. In this

case, be sure to connect *1 to *4 and *3 to *2

as shown in the figure.

Connect leads of the

same colour to each other.

Yellow (*2)

Back-up

(or accessory)

Red (*4)

Accessory

(or back-up)

Yellow (*1)

To terminal supplied with

power regardless of ignition

switch position.

Red (*3)

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (earth)

To vehicle (metal) body.

Note

In some vehicles, the ISO connector may be divided

into two. In this case, be sure to connect to both

connectors.

Note

*2 *1

*4 *3

ISO connector

Speaker leads

White: Front left 

White/black: Front left 

Grey: Front right 

Grey/black: Front right 

Green: Rear left 

Green/black: Rear left 

Violet: Rear right 

Violet/black: Rear right 

<CRB4794-A>8

Engb

Section

02 Connection

Black plate (9,1)

Note

The pin position of the ISO connector will differ

depending on the types of vehicles. Connect *5

and *6 when Pin 5 is an aerial control type. In

other types of vehicles, never connect *5 and *6.

Yellow/black (MUTE)

If you use equipment with a mute function, connect

that equipment to the Audio Mute lead. If not, keep

the Audio Mute lead free of any connections.

Power cord

Audio source will be set to mute or attenuate, while the

following sounds will not be muted or attenuated. For details,

refer to Operation Manual.

— Voice guidance of the navigation

— Incoming ringtone and incoming voice of the mobile phone

that is connected to this product via Bluetooth wireless

technology

This product

14 cm

Fuse (10 A)

Blue/white (*5)

Blue/white (*6)

To auto-aerial relay control terminal or

aerial booster power control terminal

(max. 300 mA 12 V DC).

Power supply

<CRB4794-A>9

Engb 9

Section

Connection

Black plate (10,1)

Connecting the power cord (2)

Pink (CAR SPEED SIGNAL INPUT)

This product is connected here to detect the distance the vehicle travels. Always connect the

vehicle’s speed detection circuit. Failure to make this connection will increase errors in the

vehicle’s location display.

LIGHT GREEN LEAD AT POWER CONNECTOR IS

DESIGNED TO DETECT PARKED STATUS AND MUST BE

CONNECTED TO THE POWER SUPPLY SIDE OF THE

HANDBRAKE SWITCH. IMPROPER CONNECTION OR

USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW

AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

Light green (PARKING BRAKE)

Used to detect the ON/OFF status of the handbrake. This lead must be connected to the power supply side

of the handbrake switch.

If this connection is made incorrectly or omitted, certain functions of this product will be unusable.

Power supply side

Earth side

Handbrake switch

Connection method

Clamp the lead of the power supply

side of the handbrake switch.

Clamp firmly with needle-nosed

pliers.

The position of the speed detection circuit and the position of the handbrake switch vary

depending on the vehicle model. For details, consult your authorised Pioneer dealer or an

installation professional.

Note

WARNING

CAUTION

It is strongly suggested that the speed pulse wire be connected for accuracy of navigation

and better performance.

IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING

ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE

VEHICLE´S ANTILOCK BRAKING SYSTEM, AUTOMATIC GEARBOX AND

SPEEDOMETER INDICATION.

WARNING

<CRB4794-A>10

Engb

Section

02 Connection

Andere Handbücher für AVIC-F80DAB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Navigationssystem Handbücher anderer Marken

PNI

PNI T500 Bedienungsanleitung

Kenwood

Kenwood DNN992 Bedienungsanleitung