Pioneer AVH-5300DVD Bedienungsanleitung

<CRD4571-A/N> <1>

English Français Italiano Español Deutsch Nederlands

Installation Manual

Manuel d’installation

Manuale d’installazione

Manual de instalación

Installationsanleitung

Installatiehandleiding

DVD RDS AV RECEIVER

AUTORADIO AV RDS LECTEUR DE DVD

SINTOLETTORE DVD RDS CON AV

RADIO AV RDS CON DVD

DVD-RDS-AV-EMPFÄNGER

DVD RDS AV-ONTVANGER

AVH-5300DVD

AVH-6300BT

WARNING

!To avoid the risk of accident and the potential

violation of applicable laws, no viewing of

front seat video should ever occur while the

vehicle is being driven. Also, rear displays

should not be in a location where they are visi-

bly distracting to the driver.

!In some countries or states the viewing of

images on a display inside a vehicle even by

persons other than the driver may be illegal.

Where such regulations apply, they must be

obeyed and this unit’s DVD features should

not be used.

CAUTION

!PIONEER does not recommend that you in-

stall or service your display unit yourself. In-

stalling or servicing the product may expose

you to risk of electric shock or other hazards.

Refer all installation and servicing of your dis-

play unit to authorized Pioneer service person-

nel.

!Secure all wiring with cable clamps or electri-

cal tape. Do not allow any bare wiring to re-

main exposed.

!Do not drill a hole into the engine compart-

ment to connect the yellow cable of the dis-

play unit to the vehicle battery. Engine

vibration may eventually cause the insulation

to fail at the point where the wire passes from

the passenger compartment into the engine

compartment. Take extra care in securing the

wire at this point.

!It is extremely dangerous to allow the micro-

phone lead to become wound around the

steering column or gearstick. Be sure to in-

stall the unit in such a way that it will not ob-

struct driving.

!Make sure that cables will not interfere with

moving parts of the vehicle, such as the gear-

shift, parking brake or seat sliding mechan-

ism.

!Do not shorten any cables. If you do, the pro-

tection circuit may fail to work properly.

WARNING

!LIGHT GREEN LEAD AT POWER CON-

NECTOR IS DESIGNED TO DETECT

PARKED STATUS AND MUST BE CON-

NECTED TO THE POWER SUPPLY SIDE

OF THE PARKING BRAKE SWITCH. IM-

PROPER CONNECTION OR USE OF

THIS LEAD MAY VIOLATE APPLICABLE

LAW AND MAY RESULT IN SERIOUS IN-

JURY OR DAMAGE.

Important

!This unit cannot be installed in a vehicle with-

out ACC (accessory) position on the ignition

switch.

ACC position No ACC position

!Use of this unit in conditions other than the

following could result in fire or malfunction.

—Vehicles with a 12-volt battery and negative

grounding.

—Speakers with 50 W (output value) and

4 ohm to 8 ohm (impedance value).

!To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

—Disconnect the negative terminal of the

battery before installation.

—Secure the wiring with cable clamps or ad-

hesive tape. Wrap adhesive tape around

wiring that comes into contact with metal

parts to protect the wiring.

—Place all cables away from moving parts,

such as the gear shift and seat rails.

—Place all cables away from hot places,

such as near the heater outlet.

—Do not connect the yellow cable to the bat-

tery by passing it through the hole to the

engine compartment.

—Cover any disconnected cable connectors

with insulating tape.

—Do not shorten any cables.

Section

01 Connecting the units

—Never cut the insulation of the power cable

of this unit in order to share the power

with other devices. The current capacity of

the cable is limited.

—Use a fuse of the rating prescribed.

—Never wire the negative speaker cable di-

rectly to ground.

—Never band together negative cables of

multiple speakers.

!When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an exter-

nal power amp or the vehicle’s auto-antenna

relay control terminal (max. 300 mA 12 V DC).

If the vehicle is equipped with a glass anten-

na, connect it to the antenna booster power

supply terminal.

!Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal of

the auto antenna. Doing so may result in bat-

tery drain or a malfunction.

!The black cable is ground. Ground cables for

this unit and other equipment (especially,

high-current products such as power amps)

must be wired separately. If they are not, an

accidental detachment may result in a fire or

malfunction.

En 3

English

Section

Connecting the units

Connecting the power cord

Microphone input Jack (MIC)

(AVH-6300BT only)

Microphone (supplied)

(AVH-6300BT only)

4 m

Wired remote input (WIRED REMOTE INPUT)

Hard-wired remote control adaptor can be connected (sold separately).

RGB input

17 cm

This product

Speaker leads

White: Front left 

White/black: Front left 

Gray: Front right 

Gray/black: Front right 

Green: Rear left or subwoofer 

Green/black: Rear left or subwoofer 

Violet: Rear right or subwoofer 

Violet/black: Rear right or subwoofer 

ISO connector

Note:

In some vehicles, the ISO connector may be divided

into two. In this case, be sure to connect to both

connectors.

Note:

Depending on the kind of vehicle, the

function of 2* and 4* may be different.

In this case, be sure to connect 1* to 4*

and 3* to 2*.

Yellow (2*)

Back-up

(or accessory)

Yellow (1*)

Connect to the constant 12 V

supply terminal.

Connect leads of the same

color to each other.

Fuse resistor

Red (4*)

Accessory

(or back-up)

Red (3*)

Connect to terminal controlled by

ignition switch (12 V DC).

Black (chassis ground)

Connect to a clean, paint-free metal location.

Orange/white

Connect to lighting switch terminal.

Fuse resistor

Section

01 Connecting the units

26 pin cable (Supplied with Navigation unit)

Insert the 26 pin cable in the direction

indicated in the figure.

Navigation unit

(AVIC-F220 (sold

separately)).

Antenna input

Please contact your dealer to inquire

about the connectable navigation unit.

Notes:

· Change the initial setting of this unit (refer to the Operation Manual).

The subwoofer output of this unit is monaural.

· When using a subwoofer of 70 W (2 Ω) , be sure to connect with Violet

and Violet/black leads of this unit. Do not connect anything to Green

and Green/black leads.

Connection method

1. Clamp the lead. 2. Clamp firmly with

needle-nosed pliers.

Note:

· The position of the parking brake switch depends on the vehicle model. For details,

consult the vehicle Owner’s Manual or dealer.

Yellow/black

If you use an equipment with Mute function, wire this lead to the Audio Mute lead

on that equipment. If not, keep the Audio Mute lead free of any connections.

Light green

Used to detect the ON/OFF status of the parking brake. This lead

must be connected to the power supply side of the parking brake

switch.

Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

Blue/white (6*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO

connector will differ depending

on the type of vehicle. Connect

5* and 6* when Pin 5 is an

antenna control type. In another

type of vehicle, never connect 5*

and 6*.

Blue/white (5*)

Ground side

Power supply side Parking brake

switch

Fuse resistor Violet/white

Of the two lead wires connected to the back lamp, connect the one in which the

voltage changes when the gear shift is in the REVERSE (R) position. This connection

enables the unit to sense whether the car is moving forwards or backwards.

En 5

English

Section

Connecting the units

When connecting to separately sold power amp

























This product

Rear output

(REAR OUTPUT)

Front output

(FRONT OUTPUT)

Subwoofer output

(SUBWOOFER OUTPUT)

13 cm

17 cm

Blue/white

Connect to system control

terminal of the power amp

(max. 300 mA 12 V DC).

Blue/white (6*)

Connect to auto-antenna relay control

terminal (max. 300 mA 12 V DC).

The pin position of the ISO connector

will differ depending on the type of

vehicle. Connect 5* and 6* when Pin 5

is an antenna control type. In another

type of vehicle, never connect 5* and 6*.

Blue/white (5*)

Rear speaker

Perform these connections when

using the optional amplifier.

System remote control

Front speaker Front speaker

Left Right

Rear speaker

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

Subwoofer Subwoofer

Connect with RCA cables

(sold separately)

To front output

To rear output

To subwoofer

output

Section

01 Connecting the units

When connecting the external video component and the display

This product

External video

component (sold

separately)

RCA cables (sold separately)

Audio inputs

(AUDIO INPUT)

Video input (VIDEO INPUT)

Display with RCA

input jacks (sold

separately)

Rear monitor output

(REAR MONITOR OUTPUT)To video input

To video output

To audio outputs

13 cm

Rear audio output

(REAR MONITOR OUTPUT(AUDIO))

To audio inputs

RCA cables (sold separately)

17 cm

Mini pin plug cable

(sold separately)

13 cm

!It is necessary to change AV Input in

System Menu when connecting the exter-

nal video component.

When using a display connected to rear video output

This product’s rear video output and rear

audio output are for connection of a display to

enable passengers in the rear seats to watch

the DVD, etc.

WARNING

!Never install the display in a location where it

is visible to the driver while driving.

En 7

English

Section

Connecting the units

When connecting with a

rear view camera

When this product is used with a rear view

camera, it is possible to automatically switch

from the video to rear view image when the

gear shift is moved to REVERSE (R).

WARNING

USE INPUT ONLY FOR REVERSE OR MIR-

ROR IMAGE REAR VIEW CAMERA. OTHER

USE MAY RESULT IN INJURY OR DAMAGE.

CAUTION

!The screen image may appear reversed.

!The rear view camera function is to be used

as an aid to keep an eye on trailers, or while

backing up. Do not use for entertainment pur-

poses.

!Objects in the rear view may appear closer or

more distant than they actually are.

Rear view camera input

(REAR VIEW CAMERA IN)

This product

13 cm

To video output

Rear view camera

(sold separately)

Violet/white

Of the two lead wires

connected to the back lamp,

connect the one in which the

voltage changes when the

gear shift is in the REVERSE

(R) position. This connection

enables the unit to

sense whether the car is

moving forwards or

backwards.

Fuse resistor RCA cable

(sold separately)

CAUTION

You must use a camera which outputs mirror

reversed images.

It is necessary to set Camera Polarity properly in

System Menu when connecting the rear view

camera.

Section

01 Connecting the units

Notes

!Check all connections and systems before

final installation.

!Do not use unauthorized parts as this may

cause malfunctions.

!Consult your dealer if installation requires dril-

ling of holes or other modifications to the vehi-

cle.

!Do not install this unit where:

—it may interfere with operation of the vehi-

cle.

—it may cause injury to a passenger as a re-

sult of a sudden stop.

!Do not install the display where it may (i) ob-

struct the driver’s vision, (ii) impair the perfor-

mance of any of the vehicle’s operating

systems or safety features, including air bags,

hazard lamp buttons or (iii) impair the driver’s

ability to safely operate the vehicle.

!The semiconductor laser will be damaged if it

overheats. Install this unit away from hot

places such as near the heater outlet.

!Optimum performance is obtained when the

unit is installed at an angle of less than 30°.

!To ensure proper heat dispersal when using

this unit, make sure you leave ample space

behind the rear panel and wrap any loose

cables so they are not blocking the vents

when installing the unit.

5cmcm

Leave ample

space 5 cm

5 cm

!The cords must not cover up the area shown

in the figure below. This is necessary to allow

the amplifiers to radiate freely.

1Do not cover this area.

!Make sure you leave enough gap between the

dashboard and the LCD panel of this unit so

the LCD panel can be opened and closed with-

out contacting with the dashboard.

1Dashboard

2Leave gap

3LCD panel

DIN front/rear-mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Decide the position of the side brack-

ets.

When installing in a shallow space, change

the position of side brackets (small).

En 9

English

Section

Installation

1Side bracket (small)

2Flush surface screw (5 mm × 6 mm)

2 Install the unit into the dashboard.

Insert the mounting sleeve into the dashboard.

And then secure the mounting sleeve by using

a screwdriver to bend the metal tabs (90°) into

place.

182

1Dashboard

2Mounting sleeve

3Side bracket

4Screw (2 mm × 3 mm)

DIN Rear-mount

1 Determine the appropriate position

where the holes on the bracket and the

side of the unit match.

When installing in a shallow space, use the

following screw holes.

1Use binding screws (4 mm × 3 mm) only.

2 Tighten two screws on each side.

Use any of binding screws (4 mm × 3 mm),

binding screws (5 mm × 6 mm) or flush sur-

face screws (5 mm × 6 mm), depending on

the shape of screw holes in the bracket.

1Screw

2Dashboard or console

3Factory radio mounting bracket

Note

In some types of vehicles, discrepancy may occur

between the unit and the dashboard. If this hap-

pens, use the supplied frame to fill the gap.

Removing the unit

Extend top and bottom of the trim ring out-

wards to remove the trim ring. And then loos-

en the screws (2 mm × 3 mm) to remove the

mounting sleeve.

!When reattaching the trim ring, push the

trim ring onto the unit until it clicks. (If the

trim ring is attached upside down, the trim

ring will not fit properly.)

Section

02 Installation

Andere Handbücher für AVH-5300DVD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Pioneer Stereo-Receiver Handbücher

Pioneer

Pioneer SX-850 Bedienungsanleitung

Pioneer

Pioneer sx-550 Bedienungsanleitung

Pioneer

Pioneer SX-1050 Bedienungsanleitung

Pioneer

Pioneer MVH-A210BT Bedienungsanleitung

Pioneer

Pioneer VSX-1024 Bedienungsanleitung

Pioneer

Pioneer VSX-453 Bedienungsanleitung

Pioneer

Pioneer DMH-1500NEX Bedienungsanleitung

Pioneer

Pioneer A9 SX-A9MK2-K Bedienungsanleitung

Pioneer

Pioneer SXrSTOO Bedienungsanleitung

Pioneer

Pioneer VSX-5231 Bedienungsanleitung

Pioneer

Pioneer VSX-815-K Bedienungsanleitung

Pioneer

Pioneer SX-3800 Bedienungsanleitung

Pioneer

Pioneer DMH-A345BT Bedienungsanleitung

Pioneer

Pioneer SX-580 Bedienungsanleitung

Pioneer

Pioneer AVH-P4400BH/XUUC Bedienungsanleitung

Pioneer

Pioneer VSX1017TXV Bedienungsanleitung

Pioneer

Pioneer DMH-AF555BT Bedienungsanleitung

Pioneer

Pioneer VSX-C100 Bedienungsanleitung

Pioneer

Pioneer VSX-518-K Bedienungsanleitung

Pioneer

Pioneer AVH-A7250BT Bedienungsanleitung

Pioneer

Pioneer AVH-Z7250BT Bedienungsanleitung

Pioneer

Pioneer VSX-501 Bedienungsanleitung

Pioneer

Pioneer AVH-110BT Bedienungsanleitung

Pioneer

Pioneer CT-L77 Bedienungsanleitung

Beliebte Stereo-Receiver Handbücher anderer Marken

Marantz

Marantz CINEMA 70S Bedienungsanleitung

Kenwood

Kenwood KMDX92 Bedienungsanleitung

Yamaha

Yamaha RX-830 Bedienungsanleitung

Yamaha

Yamaha RX-750 Bedienungsanleitung

Denon

Denon AVR-1311 Bedienungsanleitung

Denon

Denon AVR-S760H Bedienungsanleitung

Denon

Denon AVR-X7200W Bedienungsanleitung

Sony

Sony XAV-1500 Bedienungsanleitung

Radio Shack

Radio Shack DX-399 Bedienungsanleitung

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Yamaha

Yamaha MusicCast TSR-5B3D Bedienungsanleitung

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Sony

Sony STR-DG500 - Multi Channel Av Receiver Bedienungsanleitung

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Bedienungsanleitung

Sherwood

Sherwood S-2660CP Technisches Handbuch

Sony

Sony STR-K790 - Lifier Bedienungsanleitung

Denon

Denon DRA-697CI Bedienungsanleitung

SMART-AVI

SMART-AVI HDX-PRO Series Bedienungsanleitung